15 Umwelt
Filtern
Dokumenttyp
- Wissenschaftlicher Artikel (8) (entfernen)
Sprache
- Englisch (8) (entfernen)
Schlagworte
- Air pollution (3)
- Emission (3)
- Luftverunreinigung (3)
- Measurement (3)
- Messung (3)
- Abfluss (2)
- Autobahn (2)
- Boden (2)
- Deicing (2)
- Europa (2)
Institut
Although many German monitoring sites report declines of NOx concentrations, NO2-concentrations actually stagnate or even increase quite often. Various analyses have identified the altered compositions of nitrogen oxides (NO2/NOx-ratio) emitted by motor vehicles (resulting in an increase of primary NO2-emissions) as well as the chemical environmental conditions (mainly ground level ozone) as the main causes. The chemical conversion of NO to NO2 is often parameterized in dispersion calculations of exhaust emissions. A widely applied conversion model is the so-called Romberg approach from 1996. However, the Romberg approach has to be re-evaluated to accommodate the above-mentioned conditions. This article presents an adjustment to the Romberg approach in accordance with the measured data from 2000 to 2006, taking into consideration substantially higher NO2/NOx-ratios especially for higher NOx-concentrations. Model calculations with OSPM (Operational Street Pollution Model) including its internal chemistry module are able to reproduce very well the trends in the measured annual NO2-concentrations over a 10 year period. The relevant parameters for variations between the years are the NOx-emissions, primary NO2-emissions, ozone concentrations, wind conditions, and background concentrations. A simplified chemistry model based on annual mean NOx- and NO2-concentrations, and background ozone concentrations, as well as primary NO2-emissions is presented as a better method than the updated Romberg approach. This model simulates the annual mean NO2-concentrations much more accurately than the conventional and the updated Romberg approaches.
This study aimed to better understand nitrate transport in the soil system in a part of the state of North Rhine-Westphalia, in Germany, and to aid in the development of groundwater protection plans. An advection-diffusion (AD) cell was used in a miscible displacement experiment setup to characterize nitrate transport in 12 different soil samples from the study area. The three nitrate sorption isotherms were tested to define the exact nitrate interaction with the soil matrix. Soils varied in their properties which in its turn explain the variations in nitrate transport rates. Soil texture and organic matter content showed to have the most important effect on nitrate recovery and retardation. The miscible displacement experiment indicated a decrease in retardation by increasing sand fraction, and an increase in retardation by increasing soil organic matter content. Soil samples with high sand fractions (up to 94 %) exhibited low nitrate sorption capacity of less than 10 %, while soils with high organic matter content showed higher sorption of about 30 %. Based on parameterization for nitrate transport equation, the pore water velocity for both sandy and loamy soils were significantly different (P < 0.001). Pore water velocity in sandy soil (about 4 x 10 high 3 m/s) was about 100 to 1000 larger than in loamy soils (8.7 x 10 high 5 m/s). On the other hand, the reduction in nitrate transport in soils associated with high organic matter was due to fine pore pathways clogged by fine organic colloids. It is expected that the existing micro-phobicity increased the nitrate recovery from 9 to 32 % resulting in maximum diffusion rates of about 3.5 x 10 high 5 m/s2 in sandy soils (sample number CS-04) and about 1.4 x 10 high 7 m/s2 in silt loam soils (sample number FS-02).
Urban runoff is known to transport a significant pollutant load consisting of e.g. heavy metals, salts and hydrocarbons. Interactions between solid and dissolved compounds, proper understanding of particle size distribution, dissolved pollutant fractions and seasonal variations is crucial for the selection and development of appropriate road runoff treatment devices. Road runoff at an arterial road in Augsburg, Germany, has been studied for 3.5 years. A strong seasonal variation was observed, with increased heavy metal concentrations with doubled and tripled median concentrations for heavy metals during the cold season. Correlation analysis showed that de-icing salt is not the only factor responsible for increased pollutant concentrations in winter. During the cold period, the fraction of dissolved metals was lower compared to the warm season. In road dust, the highest metal concentrations were measured for fine particles. Metals in road runoff were found to show a significant correlation to fine particles SS63 (<63 μm). Therefore, it is debatable whether treatment devices only implementing sedimentation processes provide sufficient removal rates.
Road authorities, freight, and logistic industries face a multitude of challenges in a world changing at an ever growing pace. While globalization, changes in technology, demography, and traffic, for instance, have received much attention over the bygone decades, climate change has not been treated with equal care until recently. However, since it has been recognized that climate change jeopardizes many business areas in transport, freight, and logistics, research programs investigating future threats have been initiated. One of these programs is the Conference of European Directors of Roads (CEDR) Transnational Research Programme (TRP), which emerged about a decade ago from a cooperation between European National Road Authorities and the EU. This paper presents findings of a CEDR project called CliPDaR, which has been designed to answer questions from road authorities concerning climate-driven future threats to transport infrastructure. Pertaining results are based on two potential future socio-economic pathways of mankind (one strongly economically oriented "A2" and one more balanced scenario "A1B"), which are used to drive global climate models (GCMs) producing global and continental scale climate change projections. In order to achieve climate change projections, which are valid on regional scales, GCM projections are downscaled by regional climate models. Results shown here originate from research questions raised by European Road Authorities. They refer to future occurrence frequencies of severely cold winter seasons in Fennoscandia, to particularly hot summer seasons in the Iberian Peninsula and to changes in extreme weather phenomena triggering landslides and rutting in Central Europe. Future occurrence frequencies of extreme winter and summer conditions are investigated by empirical orthogonal function analyses of GCM projections driven with by A2 and A1B pathways. The analysis of future weather phenomena triggering landslides and rutting events requires downscaled climate change projections. Hence, corresponding results are based on an ensemble of RCM projections, which was available for the A1B scenario. All analyzed risks to transport infrastructure are found to increase over the decades ahead with accelerating pace towards the end of this century. Mean Fennoscandian winter temperatures by the end of this century may match conditions of rather warm winter season experienced in the past and particularly warm future winter temperatures have not been observed so far. This applies in an even more pronounced manner to summer seasons in the Iberian Peninsula. Occurrence frequencies of extreme climate phenomena triggering landslides and rutting events in Central Europe are also projected to rise. Results show spatially differentiated patterns and indicate accelerated rates of increases.
Measuring and characterizing airborne particulate matter (PM) is an important research area because PM can lead to impacts on health and to visibility reduction, material damage and groundwater pollution. In regard to road dust, suspension and re-suspension and the contribution of non-exhaust PM to total traffic emissions are expected to increase as a result of predicted climate scenarios. European environmental regulations have been enforced to reduce exhaust particle emissions from road traffic, but little attention has been paid to reducing non-exhaust coarse particle emissions due to traffic. Therefore, a monitoring program for coarse PM has been initiated in early 2013 to assess the predicted increase in the abundance of non-exhaust particles. Particle sampling was performed with the passive-sampler technique Sigma-2. The subsequent single-particle analysis allows for characterization of individual particles, determination of PM size distribution, and calculation of PM mass concentrations. Two motorways n ear Cologne (Koeln), Germany were selected as sampling sites, and the experimental setup in the field was realized with a so-called twin-site method. The present study reports single-particle analysis data for samples collected between May 31, 2013 and May 30, 2014. Coarse PM, generated through multi-source mechanisms, consists of, e.g., tire-wear, soot aggregates, and mineral dust. The highest mass concentration occurs at both motorways in spring, and the observed PM mainly contains traffic-abrasion particles. The field measurements show that the minimum PM concentration was found in the 5 to 12-°C temperature range, whereas the maximum concentration was observed in both the "5 to 5-°C and the 12 to 24-°C ranges, in agreement with previous laboratory measurements. Correlation between super-coarse (d p 10"80 μm, geometric equivalent diameter) PM concentration and precipitation displays a significant increase in concentration with decreasing number of precipitation events (dry weather periods).
Estimation of the effects of new emission standards on motorcycle emissions by means of modeling
(2016)
Road traffic is, in addition to the energy sector and the industry, one main source of air pollution and carbon dioxide emissions. Although most countries and manufacturers agreed to environmental regulations to reduce the pollutant emissions, particularly in urban areas with high traffic density, the impact of road traffic emissions on the environment and human health has been growing in importance steadily. Due to stricter emission standards and the binding use of emission-reducing systems (e.g. three-way catalyst) hydrocarbon emissions from passenger cars have been reduced significantly since the last two decades. Unlike to passenger cars the emissions standards of powered two-wheelers have not been adjusted since 2006 although their share of hydrocarbon emissions to the total amount of hydrocarbon emissions of road traffic is estimated to be disproportionately high. Due to the new regulation (EU) No. 168/2013 powered two-wheelers have to fulfill new emission standards from 2016 (Euro 4) and 2020 (Euro 5) onwards. Besides new limits for the tailpipe emissions the evaporative emissions are regulated separately for the first time, as they make up a high proportion to the total hydrocarbon emissions in this vehicle class. In this context, the calculation and forecast of road traffic emissions is an important tool to verify compliance of climate targets and to assess the reduction potential of emission-reducing systems. For that purpose the Federal Highway Research Institute (BASt) uses the emission- and calculation tool TREMOD (Transport Emission Model) which provides baseline data and calculated results for pollutants in almost every differentiation e.g. vehicle category, traffic situation and road type. Moreover, estimations of future emission trends, stock information and mileage distribution can be made. The main objective is to illustrate the impact of the upcoming emission standards Euro 4 and Euro 5 on the operational hydrocarbon emissions of powered two-wheelers based on statistical estimations. The significant aspect is to generate scenarios to show the reduction potential of hydrocarbon emissions of powered two-wheelers, differentiated into motorcycles and small motorcycles, in relation to the total share of hydrocarbon emissions in this vehicle class and to the total hydrocarbon emissions from road traffic. As a part of their research, the authors can make initial statements about the possible effect of the new emission standards of regulation (EU) No. 168/2013 by means of modeling with TREMOD.
Non-point sources of traffic-related pollution become a major concern as they " compared to the point-source inputs " are more difficult to be defined or controlled. It is crucial to evaluate the fraction of traffic-related contamination that is transported to the road surroundings as it could negatively impact soil, surface water and groundwater. This study describes two means through which pollutants leave the road to the surrounding environment. Three German motorways were selected (A4, A555, and A61), where runoff and deposits were analyzed to determine pollutant load moving into the roadside soil or into the drainage system. Each of the three motorways carries approximately 70,000 vehicles a day on 4 to 6 driving lanes; and they cover a broad range of truck participation in the total traffic load ranging from 5.4% to 19.8%. The three motorways represent several topographical and landscape features as forest with noise barrier and parallel as well as perpendicular orientation to the main wind direction. Sampling of runoff and deposition was done on monthly basis. Bulk deposition was collected in Bergerhoff vessels at two heights (1.5 m and 0.3 m above the ground) and in 1 m, 2.5 m, 5 m and 10 m distances from the road edge. The results showed that heavy metals as well as large amounts of mineral compounds are moving from the driving lanes into the roadside environment. This includes sodium from applying deicing salts in winter seasons, which could be found in soil, dust and water samples. Calcium and iron were also detected in almost comparable concentrations. The annual deposition flow (bulk deposition) measured at a height of 1.5 m was higher than the comparative values for urban areas and background measuring points. The spatial distribution of material deposition showed clear differences between the three motorways. The pollutant load in deposition measured near the ground surface was higher than those measured at 1.5 m above the land surface. At all three sites, a clear negative correlation between pollutant load and the distance from the roadside could be found. Nearly 90% of the concentration values of heavy metals in road runoff were below or in the range of the test values for seepage water in the German Soil Protection and Contamination Ordinance. The pH-values around 7 in runoff and adjacent soil provide a good retention capacity in the soil for the heavy metal input.
The Joint Transport Research Centre of the Organisation for Economic Co-operation and Development and the International Transport Forum recently conducted a benchmarking study of the safety and productivity of typical highway transport trucks from various countries. This paper focuses on vehicle productivity and efficiency in regard to the movement of freight. Forty vehicles from 10 countries were examined. The vehicles were designed for longer-haul applications and were classified in three separate categories: workhorse vehicles, which are the most common and can travel on most roads; high-capacity vehicles, which may be restricted to a certain class of road; and very high-capacity vehicles, which may be restricted to specific highways or routes. The metrics used in the analysis include maximum cargo mass and volume capacity, optimum cargo density, fuel consumption, and carbon dioxide output as a function of the freight task. The study found that size and weight regulations have a significant effect on the productivity and efficiency of heavy vehicles, including fuel consumption and vehicle emissions per unit of cargo transported. Significant variations were found among the vehicles from participating countries as well as within vehicle classes. It was also apparent that, in general, higher-productivity vehicles are correlated more strongly with increased cargo volume than with increased cargo mass and that larger trucks are better suited to lower-density freight than are workhorse vehicles. The study also found that it is important to consider the freight task when evaluating vehicle fuel consumption and emissions.