The ASSESS project is a collaborative project that develops test procedures for pre-crash safety systems like Automatic Emergency Braking (AEB). One key criterion for the effectiveness of e.g. AEB is reduction in collision speed compared to baseline scenarios without AEB. The speed reduction for a given system can only be determined in real world tests that will end with a collision. Soft targets that are crashable up to velocities of 80 km/h are state of the art for these assessments, but ordinary balloon cars are usually stationary targets. The ASSESS project goes one step further and defines scenarios with moving targets. These scenarios define vehicle speeds of up to 100 km/h, different collision scenarios and relative collision speeds of up to 80km/h. This paper describes the development of a propulsion system for a soft target that aims to be used with these demanding scenario specifications. The Federal Highway Research Institute- (BASt-) approach to move the target is a self-driving small cart. The cart is controlled either by a driver (open-loop control via remote-control) or by a computer (closed-loop control). Its weight is limited to achieve a good crashability without damages to the test vehicle. To the extent of our knowledge BASt- approach is unique in this field (other carts cannot move at such high velocities or are not crashable). This paper describes in detail the challenges and solutions that were found both for the mechanical construction and the implementation of the control and safety system. One example for the mechanical challenges is e.g. the position of the vehicle- center of gravity (CG). An optimum compromise had to be found between a low CG oriented to the front of the vehicle (good for driveability) and a high CG oriented to the rear of the vehicle (good for crashability). The soft target itself which is also developed within the ASSESS project will not be covered in detail as this is work of a project partner. Publications on this will follow. The paper also shows first test results, describes current limitations and gives an outlook. It is expected that the presented test tools for AEB and other pre-crash safety systems is introduced in the future into consumer testing (NCAP) as well as regulatory testing.
The Intersection 2020 project was initiated to develop a test procedure for Automatic Emergency Braking systems in intersection car-to-car scenarios to be transferred to Euro NCAP. The project aims to address current road traffic accidents on European roads and therefore sets a priority of the identification of the most important car-to-car accidents and Use Cases. Taking into account technological and practical limitations, Test Scenarios are derived from the Use Cases in a later stage of the project. This paper presents parts of a larger study and provides an overview of common car-to-vehicle(at least four wheels) collision types at junctions in Europe and specifies seven Accident Scenarios from which the three scenarios “Straight Crossing Paths (SCP)”, “Left Turn Across Path – Opposite Direction Conflict (LTAP/OD)” and “Left Turn Across Path – Lateral Direction (LTAP/LD)” are most important due to their high relevance regarding severe car-to-car accidents. Technical details about crash parameters such as collision and initial speeds are delivered. The analysis work performed is input for the definition and selection of the Use Cases as well as for the project’s benefit estimation. The numbers of accidents and fatalities in accidents at intersections involving a passenger car were shown per intersection type. In both statistics, it was found that accidents at crossroads and T- or staggered junctions are of highest relevance, followed by roundabouts. Focusing on accidents at intersections between one passenger car and another road user shows that around one-third of all accidents and related fatalities could have been assigned to car-to-PTW accidents and one-fifth of all accidents and fatalities to car-to-car accidents. Regarding car-to-car accidents with at least serious injury outcome 38% out of 34,489 car-to-car accidents happened at intersections. These figures correspond to 18% of the fatalities (4,236 fatalities in total). Considering all intersection types, around half of all related accidents happened in urban environments whereas this number decreased to one-third of all fatalities. Further, the proportion of road fatalities per country occurring at intersections varies widely across the EU. Also, there are proportionately more fatalities in daylight or twilight conditions at junctions. Use Cases are supposed to be derived from Accident Scenarios and by adding detailed information for example about the road layout, right-of-way and the vehicle trajectories prior to the collision. Instead of applying cluster algorithms to the accident data, a pragmatic approach was finally preferred to create them. Note: Use Cases serve as an intermediate step between the Accident Scenarios and the Test Scenarios which describe the actual testing conditions. Finally, 74 Use Cases were identified. This large number indicates the complexity of intersection crashes due to the combination of several parameters.