Filtern
Dokumenttyp
- Konferenzveröffentlichung (10)
- Buch (Monographie) (1)
- Bericht (1)
- Arbeitspapier (1)
Sprache
- Englisch (13) (entfernen)
Schlagworte
- Safety (6)
- Sicherheit (5)
- Conference (4)
- Konferenz (4)
- Prüfverfahren (4)
- Test method (4)
- Deutschland (3)
- Driver assistance system (3)
- Efficiency (3)
- Fahrerassistenzsystem (3)
Institut
With the present brake signal pattern the traffic behind only receives the information that the brakes are applied, however, the drivers have no information about the intensity of the braking maneuver. In this report it is examined on the basis of a study of the literature, how the rear signal pattern could be optimized for a special representation of emergency braking maneuvers. In principle there are two suitable possibilities to reduce the driver reaction time: - An increase in the area and luminance of the brake lights intuitively provide the drivers following with an impression of approaching the vehicle in front , - Flashing lights are particularly suited to attract the attention of the driver following to the deceleration of the vehicle ahead , - The following advancement is recommended as an optimization of the rear signal pattern: When the brake assistant or ABS actuates or at a vehicle deceleration rate greater than 7 m/s-², the emergency braking maneuver is signaled by flashing of the third high-mounted brake light at a rate of 3-5 Hz. As an option, the area and luminance of the two lower brake lights could be increased in addition. These measures require changes to ECE Regulations No. 7 and No. 48 as well as to the Vienna Convention. The purpose of the described solution is to reduce the number or severity of rear-end accidents.
Since 2005 the German In-Depth Accident Study (GIDAS) also records aspects of active vehicle safety. This is done because vehicles are fitted with an increasing number of active safety devices which have undoubtedly an influence on the number, severity and course of accidents. Accident researchers expect that collecting active safety data will facilitate to assess and quantify the impact of these and future devices. It is the aim of this paper to outline benefits and limitations associated with the recording of active safety aspects within indepth studies. An overview about possible areas where active safety data can be useful will be given. For that purpose single safety or comfort systems will be selected to estimate the effects of an accident database which includes variables associated with these systems. Questions with regard to the limitations of collecting active safety data will be addressed. Possible items are for example the usability of the data recorded, the real accident cause, the small number of relevant accidents, the time span needed to gather a sufficient dataset, the small share of vehicles equipped with a certain system or different functionalities of systems that are supposed to fall in the same category. As a result user needs for a reasonable data collection of active safety elements will be elaborated.
Since its beginning in 1999, the German In-Depth Accident Study (GIDAS) evolved into the presumably leading representative road traffic accident investigation in Europe, based on the work started in Hanover in 1973. The detailed and comprehensive description of traffic accidents forms an essential basis for vehicle safety research. Due to the ongoing extension of demands of researchers, there is a continuous progress in the techniques and systematic of accident investigation within GIDAS. This paper presents some of the most important developments over the last years. Primary vehicle safety systems are expected to have a significant and increasing influence on reducing accidents. GIDAS therefore began to include and collect active safety parameters as new variables from the year 2005 onwards. This will facilitate to assess the impact of present and future active safety measures. A new system to analyse causation factors of traffic accidents, called ACASS, was implemented in GIDAS in the year 2008. The whole process of data handling was optimised. Since 2005 the on-scene data acquisition is completely conducted with mobile tablet PCs. Comprehensive plausibility checks assure a high data quality. Multi-language codebooks are automatically generated from the database structure itself and interfaces ensure the connection to various database management systems. Members of the consortium can download database and codebook, and synchronize half a terabyte of photographic documentation through a secured online access. With the introduction of the AIS 2005 in the year 2006, some medical categorizations have been revised. To ensure the correct assignment of AIS codes to specific injuries an application based on a diagnostic dictionary was developed. Furthermore a coding tool for the AO classification was introduced. All these enhancements enable GIDAS to be up to date for future research questions.
In the last years there has been a decline in accident figures in Germany especially for four wheeled vehicles. At the same time, accident figures for motorcycles remained nearly constant. About 17 % of road traffic fatalities in the year 2006 were motorcyclists. 33 % of these riders were killed in single vehicle crashes. This leads to the conclusion that improving driving dynamics and driving stability of powered two wheelers would yield considerable safety gains. However, the well-known measures for cars and trucks with their proven effectiveness cannot be transferred easily to motorcycles. Therefore studies were carried out to examine the safety potential of Anti Lock Braking Systems (ABS) and Vehicle Stability Control (VSC) for motorcycles by means of accident analysis, driving tests and economical as well as technical assessment of the systems. With regard to ABS, test persons were assigned braking tasks (straight and in-curve) with five different brake systems with and without ABS. Stopping distances as well as stress and strain on the riders were measured for 9 test riders who completed 105 braking manoeuvres each. Knowing the ability of ABS to avoid falls during braking in advance of a crash and taking into account the system costs, a cost benefit analysis for ABS for motorcycles was carried out for different market penetration of ABS, i.e. equipment rates, and different time horizons. The potential of VSC for motorcycles was estimated in two steps. First the kinds of accidents that could be prevented by such a system at all have been analysed. For these accident configurations, simulations and driving tests were then performed to determine if a VSC was able to detect the critical driving situation and if it was technically possible to implement an actuator which would help to stabilise the critical situation.
The 2BeSafe project (2-Wheeler Behaviour and Safety) is a collaborative project (co financed by the European Commission) that aims to study the naturalistic behaviour of Powered-Two-Wheeler (PTW) riders in normal and critical riding situations. That includes the interaction between PTW riders and other road users and possible conflicts between them. One of the predominant causes of accidents involving PTWs is that PTWs are often overlooked by other road users. One task of the project lead by BASt therefore deals with possible improvements in conspicuity and the development of recommendations. Particularly using the findings of the studies on conflict situations, promising lighting arrangements to enhance conspicuity of PTWs during the day and at night are selected. An abstract recognizing pattern for PTWs is defined, enabling other road users (e.g. car drivers) to clearly identify riders. Lamps and outfit like lighting configurations of different colours, different helmet lights, reflect / luminescent clothing parts and retro-reflective markings are designed and manufactured. Then, the different solutions are tested in a laboratory setting using experimental motorcycles together with riders to which the equipment is fitted. As result a proposal for a uniform signal pattern or lamp configuration in the front of all motorcycles and riders will be outlined. The contribution first gives a short overview of the topics of the research project that deal with conflicts and their connection with poor conspicuity and then presents in detail the methods used in the activities concerning solutions for the improvement of conspicuity together with first results.
Although the bus belongs to the safest traffic means, single accidents can be particularly severe and concern many passengers. Especially in case of fires a high number of injured and killed persons can be the outcome. Fire safety of buses therefore is of high importance. With the increase of synthetic and plastic materials as a material for the interior equipment of buses and coaches because of their ood mechanical properties combined with low weight, the question arises whether the safety level has decreased in case of a fire during the last years - also compared to other means of transport. Because of the combustible plastics and their ability to release a high amount of heat the main fire load in buses is no longer the fuel but the plastic materials which are also often easy to ignite. Besides the flammability of the equipments, the production of smoke, the smoke development and propagation and its toxicity for the people as well as the testing methods and limit values are of interest. For those reasons research projects were initiated on behalf of the German Federal Highway Research Institute. At the one hand the fire behavior of coach interiors was examined in general focusing on fire propagation as well as fire detection and signalling. As result, recommendations with regard to early fire detection systems for the engine compartments and on-board extinguishing equipment were elaborated. At the other hand research is carried out to examine heat release, smoke, smoke propagation and its toxicity due to burning bus interior materials. The paper describes which effective and economically reasonable fire safety requirements for interiors of buses would improve the current situation. Proposals for amendments of current requirements are recommended including the specification of appropriate limit values. In particular, it is taken into consideration which reasonable fire safety standards from other transport sectors, especially the rail sector, should be transferred to buses.
Euro NCAP will start to test pedestrian Automatic Emergency Braking Systems (AEB) from 2016 on. Test procedures for these tests had been developed by and discussed between the AsPeCSS project and other initiatives (e.g. the AEB group with Thatcham Research from the UK). This paper gives an overview on the development process from the AsPeCSS side, summarizes the current test and assessment procedures as of March 2015 and shows test and assessment results of five cars that had been tested by BASt for AsPeCSS and the respective manufacturer. The test and assessment methodology seems appropriate to rate the performance of different vehicles. The best test result - still one year ahead of the test implementation - is around 80%, while the worst rating result is around 10%. Other vehicles are between these boundaries.
A methodology to derive precision requirements for automatic emergency braking (AEB) test procedures
(2015)
AEB Systems are becoming important to increase traffic safety. Test procedures in testing for consumer information, manufacturer self-certification and technical regulations are used to ensure a certain minimum performance of these systems. Consequently, test robustness, test efficiency and finally test cost become increasingly important. The key driver for testing effort and test costs is the required repeatable accuracy in a test design - the higher the accuracy, the higher effort and test costs. On the other hand, the performance of active safety systems depends on time discretization in the environment perception and other sub-systems: for instance, typical sensors supply information with a cycle time of 50 - 150 ms. Time discretization results in an inherent spread of system performance, even if the test conditions are perfectly equal. The proposed paper shows a methodology to derive requirements for a test setup (e.g. test repeats, use of driving robots, ...) as function of AEB system generation and rating method (e.g. Euro NCAP points awarded, pass/fail, ...). While the methodology itself is applicable to AEB pedestrian and AEB Car-Car scenarios, due to the lack of sufficient test data for AEB Car-Car, the focus of this paper is on AEB pedestrian scenarios. A simulation model for the performance of AEB Pedestrian systems allows for the systematic variation of the discretization time as well as test condition accuracy. This model is calibrated with test results of 4 production vehicles for AEB Pedestrian, all fully tested by BASt according to current Euro NCAP test protocols. Selected parameters to observe the accuracy of the test setup in case of pedestrian AEB is the calculated impact position of pedestrian on the vehicle front (as if no braking would have occurred), and the test vehicle speed accuracy. These variable was shown in real tests to be repeatable in the range of ± 5 cm and ± 0,25 km/h, respectively, with a fully robotized state of the art test setup. The sensitivity of AEB performance (measured in achieved speed reduction as well as overall rating result according to current Euro NCAP rating methods) towards discretization and the sensitivity of performance towards test accuracy then is compared to identify economic yet robust test concepts. These comparisons show that the available repeatability accuracy of current test setups is more than sufficient for today's AEB system capabilities. Time discretization problems dominate the performance spread especially in test scenarios with a limited pedestrian dummy reveal time (e.g. child behind obstruction, running adult scenarios with low car speeds). This would allow to increase test tolerances to decrease test cost. A methodology which allows to derive the required tolerances in active safety tests might be valuable especially for NCAPs of emerging countries that do not have the necessary equipment (e.g. driving robots, positioning units) available for the full-scale and high tolerance EuroNCAP active safety procedures yet still want to rate active safety systems, thus improving the global safety.
Accidents between right turning trucks and straight riding cyclists often show massive consequences. Accident severity is much higher than in other accidents. The situation is critical especially due to the fact that, in spite of the six mirrors that are mandatory for ensuring a minimum field of sight for the truck drivers, cyclists in some situations cannot be seen or are not seen by the driver. Either the cyclist is overlooked or is in a blind spot area that results from the turning manoeuvre of the truck and its articulation if it is a truck trailer or truck semitrailer combination. At present driver assistance systems are discussed that can support the driver in the turning situation by giving a warning when cyclists are riding parallel to the truck just before or in the turning manoeuvre. Such systems would generally bear a high potential to avoid accidents of right turning trucks and cyclists no matter if they ride on the road or on a parallel bicycle path. However, performance requirements for such turning assist systems or even test procedures do not exist yet. This paper describes the development of a testing method and requirements for turning assist systems for trucks. The starting point of each development of test procedures is an analysis of accident data. A general study of accident figures determines the size of the problem. In-depth accident data is evaluated case by case in order to find out which are representative critical situations. These findings serve to determine characteristic parameters (e.g. boundary conditions, trajectories of truck and cyclist, speeds during the critical situation, impact points). Based on these parameters and technical feasibility by current sensor and actuator technology, representative test scenarios and pass/fail-criteria are defined. The outcome of the study is an overview of the accident situation between right turning trucks and straight driving cyclists in Germany as well as a corresponding test procedure for driver assistance systems that at this first stage will be informing or warning the driver. This test procedure is meant to be the basis for an international discussion on introducing turning assist systems in vehicle regulations.
Camera-monitor systems (CMS) can be used in motor vehicles to display the driver's rear view on a monitor mounted inside the vehicle. This also offers the possibility of replacing conventional exterior mirrors with suitable CMS and thereby implementing new design concepts with aerodynamic advantages. However, as exterior mirrors are safety-relevant vehicle parts for securing the driver's indirect rear view (requirements specified in UN Regulation No. 46), the question arises whether CMS can provide an equivalent substitute for mirrors. In the scope of this study, CMS and conventional exterior mirrors were compared and assessed in test drives and static tests under different external conditions. On the one hand, the examination of technical aspects, and on the other hand, issues pertaining to the design of the human-machine interaction, were the objects of the study. Two vehicles were available for the trials with passenger vehicles: A vehicle, manufactured in small series, which is already equipped with CMS as sole replacement for the exterior mirrors, as well as a compact class vehicle which had a CMS retrofitted by the car manufacturer in addition to conventionally used exterior mirrors. The latter could be covered exclusively for trips with CMS. A tractor unit with semitrailer was available for the truck trials. The driver's cabin was equipped with a CMS system developed by the vehicle manufacturer. In general, it was shown that it is possible to display the indirect rear view sufficiently for the driver, both for cars and trucks, using CMS which meet specific quality criteria. Depending on the design, it is even possible to receive more information about the rear space from a CMS than is possible with mirror systems. It was also shown that the change from mirrors to CMS requires a certain period of familiarisation. However, this period is relatively short and does not necessarily result in safety-critical situations.