Filtern
Erscheinungsjahr
Dokumenttyp
- Konferenzveröffentlichung (637) (entfernen)
Schlagworte
- Conference (386)
- Konferenz (382)
- Germany (212)
- Deutschland (209)
- Unfall (188)
- Accident (187)
- Safety (123)
- Sicherheit (122)
- Injury (117)
- Verletzung (117)
Institut
As investigations by BASt have shown, a bond between concrete surfaces and bases may be a disadvantage when water penetrates via joints and from the sides if the bond becomes partially detached at an early stage. Free water may penetrate into the area between the concrete surface and the base and build up in areas where the bond is still intact. The high pressure caused by lorry wheels rolling over the pavement causes hydrodynamic pumping. This creates very high flow speeds with considerable corrosion power. This results in the base course surface being eroded in the areas where heavy vehicles drive over the road and may even lead to water and fine particles from the base courses being expelled through the longitudinal joints between the pavement slab and the lower hard shoulder or first overtaking lane. The erosion of the base leads unavoidably to the bearing conditions deteriorating and increased loading of the concrete surface. Cracks may occur and, later stepping-off and tilting of the plates components. This significantly deteriorates the evenness and consequently the service value of the road. This finally leads to a reduction in the service life of the concrete surface. To avoid such damage water which has penetrated must be able to lose pressure and to then seep away. A possible solution is: A nonwoven fabric substance between concrete suface and bound base course. This construction method has proved himselve on numerous test road sections and were rightly included in the new Codes of Practice for the Standardisation of the Upper Structure of Traffic-Bearing Surfaces (Richtlinien für die Standardisierung des Oberbaues von Verkehrsflächen- RStO).
Federal highway A 26 in Germany : reinforced dams in soft soils - control method according DIN 1054
(2004)
In 2001 the construction of the Federal Highway A 26 in Lower Saxony (north of Germany) was started. In this area the underground is without any substantial bearing capacity as it consists of soft layers ( clay, peat) with a thickness of up to 12 m. Because it was not possible to exchange the soil neither completely nor partially pre-loading procedure (consolidation method) was chosen for this construction. Short- and long-term stability are ensured by the use of high-tensile fabrics for reinforcement at the dam basis. The vertical and horizontal deformations and the stress changes in the soil, caused by the pre-load procedure, has to be controlled by special geotechnical measurements. Additionally, in the higher parts of the dam the strain behaviour of the high-tensile fabrics is measured. These measurements form the basis for the application of the control method according DIN 1054. In this article, the special circumstances of this project are described. Further on the geotechnical measurements, the winning and evaluation of the necessary parameters of the subsoil, and the consequences of these data for the ongoing of the project are laid down. Intermediate results of the geotechnical measurements are described.
Seit mehreren größeren Brandereignissen in Straßentunneln um die Jahrtausendwende wurde sowohl im baulichen Brandschutz als auch in der sicherheitstechnischen Tunnelausstattung viel getan. Zahlreiche technische Neu- und Weiterentwicklungen haben seither Eingang in Bau, Ausstattung und Betrieb der Bauwerke gefunden. Im europäischen aber auch weltweiten Vergleich befinden sich die deutschen Straßentunnel auf einem sehr hohen Sicherheitsniveau. Dies ist auch erforderlich, da Deutschland als Transitland in Europa über ein hoch belastetes Straßennetz verfügt. Tunnel stellen neuralgische Punkte in diesem Netz dar. Daher gilt es hier für den Nutzer ein Optimum an Sicherheit zu gewährleisten, gleichzeitig aber auch den Verkehrsfluss so gering wie möglich durch Wartungs- bzw. Sperrzeiten der Tunnelröhren zu behindern. Mit diesem Tagungsband sollen die neuesten Erkenntnisse sowohl zur Verkehrssicherheit in Tunneln, als auch zur bautechnischen Sicherheit für die Verwendung in der alltäglichen Praxis nähergebracht werden. Nach einem allgemeinen Überblick zum Stand von aktuellen Bau-, Instandsetzungs- und Nachrüstungsmaßnahmen im deutschen Fernstraßentunnelnetz erfolgt die Vorstellung zweier Forschungsprojekte der BASt, dem europäischen Projekt ECOROADS, welches die Harmonisierung zwischen Sicherheitsanforderungen auf freier Strecke und Tunnel zum Inhalt hat, und dem BASt-eigenen Modelltunnel, in dem längsneigungsabhängige, modellmaßstäbliche Rauchausbreitungsuntersuchungen vorgenommen wurden. Im zweiten Themenbereich, der die Grundlagen für Planung und Bau fokussiert, wird auf die Fortschreibung des betriebstechnischen Regelwerks, die Entwicklung von Kostenansätzen für Straßentunnel sowie auf planerische Herausforderungen im Rahmen des Großprojektes Fehmarnbeltquerung eingegangen. Im Themenschwerpunkt Tunnelbetrieb werden neue Erkenntnisse zur Belüftung von Straßentunneln bei Stau und den damit verbundenen Auswirkungen auf die Risikoanalyse vorgestellt. Außerdem gibt es ein Update zum Stand der Umsetzung des Pilotprojektes Tunnelsimulator aus zwei Bundesländern. Im Rahmen der Beiträge zu Instandsetzung und Nachrüstung von Straßentunneln wird dem aktuellen Thema des Umgangs mit Chloridbelastungen von Tunnelinnenschalen nachgegangen, sowie den Besonderheiten bei der Nachrüstung mehrerer Bestandstunnelbauwerke der Stadt Köln mit Schwerpunkt auf dem Stadtautobahntunnel Kalk. An dieser Stelle sei allen Autoren gedankt, die zu dieser gelungenen Veranstaltung beigetragen haben.
Automated driving will provide many kinds of benefits - some direct and some indirect. The benefits originate at the individual level, from changes in the behaviour of drivers and travellers with regard to driving and mobility, ending up with benefits at the social level via changes in the whole transport system and society, where many of the current planning and operations paradigms are likely to be transformed by automated driving. There may also be disbenefits, particularly at a social level, for example in intensity of travel which could result in additional congestion and increased use of natural resources. There may also be unintended consequences. For example, we do not know the impacts on public transport: driverless vehicles could provide a means to a lower cost service provision, but the availability of automated cars could lead to more car travel at the expense of collective transport.
In line with the new definition introduced by the European Commission (EC), the number of seriously injured road casualties in Germany for 2014 is assessed in this study. The number of MAIS3+ casualties is estimated by two different methodological approaches. The first approach is based on data from the German Inâ€Depth Accident Study (GIDAS), which is closely related to the German Road Traffic Accident Statistics. The second approach is based on data from the German TraumaRegister DGU-® (TRâ€DGU), which includes many more hospitals but not all MAIS3+ injuries.
Im Erd- und Straßenbau ist es in den letzten Jahren bei bindemittelbehandelten sulfathaltigen Böden wiederholt zu teilweise erheblichen Schäden durch Quellhebungen gekommen, die auf eine Mineralreaktion im Boden zurückzuführen sind. Werden Böden mit natürlichem Sulfatgehalt zu bautechnischen Zwecken mit calciumbasierten Bindemitteln behandelt, so kann das Bindemittel unter bestimmten Randbedingungen mit den im Gips enthaltenen Sulfationen zum Mineral Ettringit reagieren. Infolge der mit dieser Mineralneubildung verbundenen Volumenvergrößerung kann es zu erheblichen Hebungsschäden kommen. Die für die Reaktion des Sulfattreibens im Boden maßgebenden Einflussfaktoren sind zwar grundsätzlich bekannt, quantitative Prüfmethoden und standardisierte Strategien zur Gefahrenabwehr lagen bis dato allerdings noch nicht vor. Das Ziel des Forschungsvorhabens, über das in diesem Beitrag berichtet wird, war die Entwicklung eines praxistauglichen Prüfverfahrens als Grundlage für eine hieraus abzuleitende Prüfvorschrift. Hierfür wurden an Proben aus verschiedenen Boden-Bindemittelgemischen mit definierten Sulfatgehalten Quellhebungsversuche geplant, durchgeführt und ausgewertet. Im Ergebnis wurde ein annähernd linearer Zusammenhangzwischen dem Sulfatgehalt im Boden und den eingetretenen Quellhebungen festgestellt. Die Ergebnisse zeigen ferner, dass eine Behandlung sulfathaltiger Böden mit Weißfeinkalk mit größeren Quellhebungen verbunden ist als eine Behandlung mit Zement.
Die Europäischen Normen für Erdarbeiten werden im CEN/TC 396 "Earthworks" erarbeitet. Das Sekretariat des CEN/TC 396 wird vom französischen Normungsinstitut AFNOR gehalten. Die Normungsarbeit wird im DIN-Ausschuss NA 005-05-22 AA "Erdarbeiten (SpA zu CEN/TC 396), Gemeinschaftsausschuss mit FGSV GA 5.01" gespiegelt. Vertreter des Spiegelausschussesarbeiten in den verschiedenen Arbeitsgruppen (working groups (WG)) des CEN/TC 396 mit. In den Jahren 2009 und 2010 wurden die Gremien konstituiert und mit der Normungsarbeit begonnen, zunächst überwiegend durch die Zusammenstellung der vorhandenen Regelungen in den Mitgliedsstaaten (siehe auch Beitrag Vogel/Leister/Heyer zur Erd- und Grundbautagung 2013). Im November 2014 wurden vom CEN/TC 396 die Arbeitsaufträge("work items") offiziell gestartet.
Die Länderarbeitsgemeinschaften Bodenschutz (LABO), Abfall (LAGA) und Wasser (LAWA) haben im September 2005 das Bundesumweltministerium gebeten, bundeseinheitliche, rechtsverbindliche Anforderungen an die Verwertung von mineralischen Abfällen in technischen Bauwerken und in bodenähnlichen Anwendungen zu regeln. Die Umweltministerien der Länder haben in ihren Stellungnahmen zum 2. Arbeitsentwurf der Mantelverordnung Forderungen gestellt, bei deren Umsetzung der Einsatz von mineralischen Ersatzbaustoffen im Verkehrswegebau stark eingeschränkt und unwirtschaftlich würde. Der Wille zur Schonung natürlicher Ressourcen ist nicht erkennbar. Anforderungen an Straßenbauwerke, an den Umweltschutz und an die Kreislaufwirtschaft konkurrieren in vielen Bereichen miteinander. Im Gesetzgebungsverfahren sind bisher trotz Gesprächen zwischen den Ressorts auf Arbeitsebene in grundlegenden Aspekten keine Einigung oder von Allen tragbare Kompromisse erzielt worden. Der Verkehrswegebau ist Hauptabnehmer der Ersatzbaustoffe, geht mit großen Mengen des Primärbaustoffs "Boden" um, ist aber auch "Abfallerzeuger". In der Mantelverordnung werden Regelungen getroffen, die stark in die Belange des Straßenbaus eingreifen. Aus diesem Grund ist die Beteiligung der Straßenbauverwaltung erforderlich, um die bautechnische und bauvertragliche Kompetenz sicher zu stellen, das Potenzial für Boden- und Grundwasserschutz auszuschöpfen und natürliche Ressourcen zu schonen. Die wichtigsten Aspekte zum umweltgerechten Einsatz von Boden und Ersatzbaustoffen aus der Sicht des Straßenbaus werden vorgestellt.
Cycling and designing for cyclist in Germany: an overview of road safety, research and guidelines
(2016)
Cycling is considered a social, eco-friendly, pollution-free, low noise and healthy activity and mode of transportation. There are currently around 67 million bicycles in Germany. This number is expected to increase in the near future with greater use of electromotive assisted bicycles. Regarding the expected increase, there should be additional attention given to road traffic accidents involving cyclists. In 2014, 396 cyclists were killed in road accidents in Germany, which is 12 % of all road fatalities. Also in 2014, Germany reported over 78,000 injuries to cyclists. The majority of the fatalities (about 58 %) and 83 % of the serious injuries to cyclists occurred in urban areas. This paper will examine three aspects concerning cyclists. First, the paper will show the main current developments, for example the National Cycling Plan 2020, the effects of the road safety programme and provide an analysis of the German national accident statistics. Second, the paper will give an overview of the regulations, guidelines for road traffic and designing of cycling facilities. Lastly, this study will detail the current and completed research in Germany addressing cyclist. For example, the paper will discuss the topic "Accidents between Turning-off Trucks and Cyclists" Accidents between right turning trucks and straight riding cyclists often show massive consequences. Accident severity is much higher than in other accidents. The situation is critical especially due to the fact that, in spite of the six mirrors that are mandatory for ensuring a minimum field of sight for the truck drivers, cyclists in some situations cannot be seen or are not seen by the driver. Either the cyclist is overlooked or is in a blind spot area that results from the turning manoeuvre of the truck. At present driver assistance systems are discussed that can support the driver in the turning situation by giving a warning when cyclists are riding parallel to the truck just before or in the turning manoeuvre. The paper will describe the requirements for turning assist systems for trucks. The outcome of the study is an overview of the accident situation between right turning trucks and straight driving cyclists in Germany as well as a corresponding test procedure for driver assistance systems. Below are several other projects which will be investigated, too: Accident Risk and Acceptance of Traffic-Rules by Cyclists ; Safety Improvement in Terms of Using Bicycle Paths in the Opposite Direction ; Cycling in Mixed-Traffic ; Observation of Pedal Electric Cycles Riders to Identify Safety Concerns. These three aspects will provide the current situation on the topic of cyclist safety in Germany.
Bewertung der strukturellen Substanz für die systematische Erhaltungsplanung von Betonfahrbahndecken
(2016)
"Mobilität ist zentrale Voraussetzung für wirtschaftliches Wachstum, Beschäftigung und Teilhabe des Einzelnen am gesellschaftlichen Leben." Dieser Leitsatz des BMVI setzt eine intakte und funktionierende Infrastruktur voraus. Im Kontext mit dem Investitionshochlauf in den nächsten Jahren ist für das Bundesfernstraßennetz insbesondere ein netzbezogenes systematisches Vorgehen im Rahmen der Baulichen Erhaltung von Relevanz. Bei der Planung von Erneuerungsmaßnahmen ist dabei die Kenntnis über den Zustand der strukturellen Substanz und deren langfristige Entwicklung von zentraler Bedeutung. Nachfolgend wird ein Verfahren vorgestellt, das die mechanisch und statistisch abgesicherte Bewertung und Prognose der strukturellen Substanz von Betonfahrbahndecken ermöglicht. Zudem werden die Anwendung und das Vorgehen anhand eines Praxisbeispiels aufgezeigt.
Die Ermittlung einer voraussichtlichen Restnutzungsdauer von Verkehrsbefestigungen und somit der Abschätzung des Eingreifzeitpunktes für eine grundhafte Erneuerung ist ohne die Kenntnis der strukturellen Substanz nur sehr unzureichend zu bewerkstelligen. Mit Vorliegen des Entwurfes zu den "Richtlinien zur Bewertung der strukturellen Substanz des Oberbaus von Verkehrsflächen in Asphaltbauweise" (RSO Asphalt) ist zwar ein hierfür nutzbares Verfahren verfügbar, allerdings basiert dieses auf der Analyse von Laborversuchen an den aus Streckenabschnitten zu entnehmenden Bohrkernen, wodurch eine netzweite Anwendung nicht praktikabel ist. Um trotzdem einen umfassenden Einsatz zu ermöglichen und eine deutliche Verbesserung gegenüber bisherigen Verfahren herbeizuführen, können aber begründete Annahmen zu den Materialkennwerten getroffen werden. Alle weiteren Eingangsdaten des Verfahrens decken sich mit denen des bisherigen. Deren Vollständigkeit und Plausibilität muss zukünftig mehr Bedeutung zugemessen werden.
Fire incidents are among the most relevant for people in a tunnel. Therefore, it is important to be sufficiently prepared for such events. A large scale fire test is to be used to help evaluate the initial burning duration and the time it takes for the fire to spread to other vehicles in the tunnel, and in particular how long it takes for a truck carrying wooden pallets to catch fire, taking into consideration the extremely high temperatures. The goal, therefore, is to determine the time it takes for a fire to spread to other vehicles in the tunnel. In the large scale fire test, an accident in a tunnel with one-way traffic is simulated between a truck loaded with approximately 3.7 t of wooden Europol pallets and a passenger car. Directly behind each of the vehicles involved in the accident there is another car which stops at a distance of 1.0 m. Approximately 300 litres of burning diesel are discharged from the truck's fuel tank, which is simulated by using approximately 400 litres of isopropanol. A 10 m-² burning pool forms underneath the truck. Other objectives of the large scale fire test are the validation of the CFD models and the evaluation of the progression of the thermal release ratios estimated for the simulation. The thermal release ratios generated in the test are determined and evaluated using various models.
Die Europäischen Normen für Erdarbeiten werden im CEN/TC 396 "Earthworks" erarbeitet. Das Sekretariat des CEN/TC 396 wird vom französischen Normungsinstitut AFNOR gehalten. Die Normungsarbeit wird im DIN-Ausschuss NA 005-05-22 AA "Erdarbeiten (SpA zu CEN/TC 396), Gemeinschaftsausschuss mit FGSV GA 5.01" gespiegelt. Vertreter des Spiegelausschusses arbeiten in den verschiedenen Arbeitsgruppen (Working Groups (WG)) des CEN/TC 396 mit. In den Jahren 2009 und 2010 wurden die Gremien konstituiert und mit der Normungsarbeit begonnen, zunächst überwiegend durch die Zusammenstellung der vorhandenen Regelungen in den Mitgliedsstaaten (siehe auch Beitrag Vogel/Leister/Heyer zur Erd- und Grundbautagung 2013). Im November 2014 wurden vom CEN/TC 396 die Arbeitsaufträge ("work items") offiziell gestartet.
Die Länderarbeitsgemeinschaften Bodenschutz (LABO), Abfall (LAGA) und Wasser (LAWA) haben im September 2005 das Bundesumweltministerium gebeten, bundeseinheitliche, rechtsverbindliche Anforderungen an die Verwertung von mineralischen Abfällen in technischen Bauwerken und in bodenähnlichen Anwendungen zu regeln. Die Umweltministerien der Länder haben in ihren Stellungnahmen zum 2. Arbeitsentwurf der Mantelverordnung Forderungen gestellt, bei deren Umsetzung der Einsatz von mineralischen Ersatzbaustoffen im Verkehrswegebau stark eingeschränkt und unwirtschaftlich würde. Der Wille zur Schonung natürlicher Ressourcen ist nicht erkennbar. Anforderungen an Straßenbauwerke, an den Umweltschutz und an die Kreislaufwirtschaft konkurrieren in vielen Bereichen miteinander. Im Gesetzgebungsverfahren sind bisher trotz Gesprächen zwischen den Ressorts auf Arbeitsebene in grundlegenden Aspekten keine Einigung oder von Allen tragbare Kompromisse erzielt worden. Der Verkehrswegebau ist Hauptabnehmer der Ersatzbaustoffe, geht mit großen Mengen des Primärbaustoffs "Boden" um, ist aber auch "Abfallerzeuger". In der Mantelverordnung werden Regelungen getroffen, die stark in die Belange des Straßenbaus eingreifen. Aus diesem Grund ist die Beteiligung der Straßenbauverwaltung erforderlich, um die bautechnische und bauvertragliche Kompetenz sicher zu stellen, das Potenzial für Boden- und Grundwasserschutz auszuschöpfen und natürliche Ressourcen zu schonen. Die wichtigsten Aspekte zum umweltgerechten Einsatz von Boden und Ersatzbaustoffen aus der Sicht des Straßenbaus werden vorgestellt.
Risk-based approach for the protection of land transport infrastructure against extreme rainfall
(2016)
The aim of the research project "Risk based approach for the protection of transport infrastructure against extreme rainfall RAINEX" is the development of a practical methodology for the identification and assessment of both vulnerable as well as critical transport infrastructures towards extreme rainfall events consequences. The developed methodology is based on expert knowledge and includes qualitative and semi-quantitative analyses regarding the assessment of the vulnerability and criticality of relevant transport infrastructures. The process chain from the spatial rainfall to the concentrated runoff in the river channel was shown to assess the local hazard resulting in the local risk. The main result of the project is a practice-oriented and applicable methodology and a comprehensive and well-developed security handbook.
The performance of asphalt by low temperatures is largely determined by the viscosity of the binder respectively the mortar of the asphalt. The traditional test methods for binder (e.g. ball-draw viscosimeter) are limited to temperatures above the service range of temperature for an asphalt construction. The Dynamic Shear Rheometer (DSR) is limited to temperatures above 30-°C whereas the Bending Beam Rheometer (BBR) is limited to temperatures below -10-°C and not applicable to mortar. Especially the gap in the temperature of these test methods is very important to characterize the viscosity behavior of binder and mortar over the whole range of the service temperatures, which represent the typical environmental conditions of over the seasons, for an asphalt construction. Tension retardation experiments seem to be very useful to bridge the gap. They address the low temperature behavior of binder and mortar. With this test method the flow characteristics of binder (pen grade and any modification) and any kind of mortar in the service temperature range, in particular at low temperatures of -25-°C can be determined with a high precision, and assessed, via the physically interpretable material characteristics quantity of tension viscosity. Furthermore the present findings indicate the potential of extrapolation the results of the Tension retardation for a prediction of the rutting resistance of asphalt mixtures. As part of several research Projects, BASt (Federal Highway Research Institute) investigated the effects of different modifications of the binder to low temperature behavior of the binder by the tension retardation test. This paper is intended to provide a more detailed description of the test method Tension Retardation, selected results and related findings.
Research to inform policy is often challenged with how to genuinely use and implement research findings in decision-making and policy-planning. To begin with, the dialogue between researchers and decision-makers is essential to ensure profound understanding and legitimate interpretations of the results. Furthermore, the step to drawing practical conclusions and processing them into actions can only succeed if research findings are diffused to decision-making levels with influence on the matter, and mechanisms to knowledge transfer in the presence of a stable, favourable policy environment exist. Research investments into the topic of electromobility in Europe are substantial, and subtopics aiming to inform national policy-makers address a complex set of aspects from environmental and societal to technological and economic. This paper has a two-fold objective, the first of which is to present the results of scenarios to explore electromobility deployment in Finland, Germany and the European Union. The second is to discuss the challenges and solutions to bridge the gap from research findings towards decision-making and policy-planning, using the authors' electromobility scenario work as an example. The electromobility scenarios were built using the VECTOR21 model (Mock, 2010), and the rationale was to simulate vehicle sales and markets under different policy settings and calculate the most economical solution to fulfill regulation on COâ‚‚ emissions as set by the European Commission (2009). The model allows calculating the market diffusion of alternative powertrain technologies to the European market until 2030, taking into account different taxation schemes, incentives and other country-specific characteristics. The authors also present the cost-benefit-analysis of the modelling results to assess the different scenarios and to show variation between regions regarding profitability of alternative technological or political support and interventions. To proceed from research findings towards decision-making and policy-planning, the authors made observations relating to transfer of research knowledge and interpretation of their electromobility scenario results in national policy contexts. An evaluation of how the function of research to inform policy in this case succeeded is provided. In addition, the influence of expert opinions on the political decision-making process will be discussed through experiences from an expert questionnaire conducted to survey the importance of costs, time requirement, acceptance and other criteria of promotion measures of electromobility.
With the introduction of the German Highway Capacity Manual (HBS) in January 2002 (FGSV, 2002), all methods for the evaluation of the performance of highway facilities were, for the first time in Germany, simultaneously updated and consolidated in a single work following the ideas of the American Highway Capacity Manual (HCM). This paper gives an overview of the new 2015 edition of the German HBS and describes the changes as for example the addition of chapters for freeway, rural roads, and major urban street facilities, comprising segments and intersections.
Die Kommunikation zwischen Fahrzeugen und Infrastrukturkomponenten steht vor der Einführung in Europa. Dieser Beitrag stellt zunächst die grundlegende Technologie zum Austausch von Nachrichten und ein Pilotprojekt vor, innerhalb dessen eine sichere Fahrzeug-zu-Infrastruktur Kommunikation konzipiert und praktisch erprobt wird. Darauf aufbauend werden Sicherheitsfragestellungen von Infrastrukturkomponenten beleuchtet und ein Einblick in das Schlüsselmanagement sowohl für Fahrzeuge als auch Infrastrukturkomponenten gegeben.