Filtern
Erscheinungsjahr
Dokumenttyp
- Konferenzveröffentlichung (37)
- Buch (Monographie) (23)
- Wissenschaftlicher Artikel (15)
- Arbeitspapier (10)
- Teil eines Buches (Kapitel) (4)
Schlagworte
- Safety (89) (entfernen)
Institut
- Abteilung Fahrzeugtechnik (89) (entfernen)
It is commonly agreed that active safety will have a significant impact on reducing accident figures for pedestrians and probably also bicyclists. However, chances and limitations for active safety systems have only been derived based on accident data and the current state of the art, based on proprietary simulation models. The objective of this article is to investigate these chances and limitations by developing an open simulation model. This article introduces a simulation model, incorporating accident kinematics, driving dynamics, driver reaction times, pedestrian dynamics, performance parameters of different autonomous emergency braking (AEB) generations, as well as legal and logical limitations. The level of detail for available pedestrian accident data is limited. Relevant variables, especially timing of the pedestrian appearance and the pedestrian's moving speed, are estimated using assumptions. The model in this article uses the fact that a pedestrian and a vehicle in an accident must have been in the same spot at the same time and defines the impact position as a relevant accident parameter, which is usually available from accident data. The calculations done within the model identify the possible timing available for braking by an AEB system as well as the possible speed reduction for different accident scenarios as well as for different system configurations. The simulation model identifies the lateral impact position of the pedestrian as a significant parameter for system performance, and the system layout is designed to brake when the accident becomes unavoidable by the vehicle driver. Scenarios with a pedestrian running from behind an obstruction are the most demanding scenarios and will very likely never be avoidable for all vehicle speeds due to physical limits. Scenarios with an unobstructed person walking will very likely be treatable for a wide speed range for next generation AEB systems.
Anforderungen, Zielkonflikte
(2019)
Um Sicherheit und Umweltverträglichkeit von Straßen- bzw. Kraftfahrzeugen zu gewährleisten, werden an die Gestaltung der Fahrzeuge technische Anforderungen gestellt. Es gibt Anforderungen durch den Gesetzgeber, die erfüllt werden müssen, um ein Fahrzeug in den Verkehr bringen zu dürfen. Darüber hinaus bestehen herstellerinterne Anforderungen an das Produkt, die über das vom Gesetzgeber geforderte Maß hinausgehen, um den Kundenwünschen und der Firmenphilosophie zu genügen. Und als dritter Punkt stellen auch Verbraucherschutz-Organisationen Kriterien auf, anhand derer sie die Eigenschaften der auf dem Markt befindlichen Fahrzeuge bewerten und die Fahrzeuge eingruppieren, was dann der Kundeninformation dient. Auch diese Anforderungen gehen über die des Gesetzgebers hinaus. Das Setzen der gesetzlichen Mindestanforderungen ist für die Fahrzeugtechnik mittlerweile jedoch nicht mehr einzelnen Staaten überlassen. Vielmehr sind die für die Genehmigung von Fahrzeugtypen einzuhaltenden Bedingungen international harmonisiert: Für die EU sind dies EU-Richtlinien oder EU-Verordnungen, die von der Europäischen Kommission in Brüssel vorgeschlagen werden. Für über die EU hinausgehende Staaten bzw. Regionen sind dies unter anderem Regelungen der UN, erstellt von der UN-Wirtschaftskommission für Europa (UNECE) in Genf.
Die vom Bundesministerium für Verkehr, Bau und Stadtentwicklung (BMVBS) beauftragte Studie zu den Auswirkungen neuartiger Lastzugkombinationen auf die Infrastruktur, den Verkehrsablauf und die Verkehrssicherheit liegt jetzt vor. Die Untersuchungen der Arbeitsgruppe der Bundesanstalt für Straßenwesen (BASt) konzentrieren sich ausschließlich auf die technischen Fragestellungen. Die wesentlichen Ergebnisse: - Eine erhöhte Straßenschädigung ist wegen der zugrunde gelegten neuen Fahrzeugtypen mit acht Achsen nicht zu erwarten. Infolge der prognostizierten allgemeinen Transportleistungssteigerung ist dieser Effekt jedoch von begrenzter Dauer. - Die Beanspruchung der Brücken wird durch 60-Tonnen-Lastzugkombinationen deutlich erhöht, was Ersatz oder Verstärkungen erforderlich machen wird. - Für die Tunnel der Bundesfernstraßen können sich wegen des deutlich größeren Ladevolumens höhere Brandlasten ergeben, mit der Folge erhöhter Anforderungen an die Sicherheitsausstattung. - Probleme bei der Befahrbarkeit von Kreisverkehren, Straßenkreuzungen und -einmündungen sowie Parkplätzen auf Rastanlagen werden sich infolge der größeren Fahrzeuglängen ergeben. Durch zusätzliche fahrzeugtechnische Einrichtungen - wie Lenkachse oder zusätzliche Gelenke - können diese gemindert werden. - Nach den vorliegenden Erfahrungen aus dem Ausland sind für ausreichend motorisierte und mit zuverlässigen Bremsanlagen ausgerüstete Transportfahrzeuge keine gravierenden Probleme hinsichtlich des Verkehrsablaufs und der Verkehrssicherheit auf Autobahnen zu erwarten. Im nachgeordneten Straßennetz (insbesondere Landes-, Kreis- und Gemeindestraßen) ist mit negativen Auswirkungen der Lastzugkombinationen sowohl auf die Verkehrssicherheit als auch auf die Leistungsfähigkeit der Straßen zu rechnen. So muss beispielsweise mit längeren Überholwegen und längeren Räumzeiten - etwa beim Abbiegen und an Bahnübergängen - gerechnet werden. - Die derzeitigen Schutz- und Rückhaltesysteme sind nicht für 60-Tonnen-Lastzugkombinationen ausgelegt. Derartige Rückhaltesysteme müssten erst entwickelt werden. Aufgrund der höheren Fahrzeuggewichte könnte die Unfallschwere bei Auffahrunfällen deutlich zunehmen. Moderne Fahrerassistenzsysteme (Spurhalteassistent sowie Bremsassistent mit Abstandsradar) könnten jedoch grundsätzlich dazu beitragen, sowohl Unfallrisiko als auch Unfallschwere zu verringern.
Der Autor berichtet über das neu eingerichtete Expertennetzwerk HUMANIST, das sich mit Fragen der nutzerorientierten und sicherheitsgerechten Gestaltung von Fahrerassistenz- und Informationssystemen befasst. Ziel sind die Zusammenführung und Integration entsprechender Forschungsaktivitäten auf europäischer Ebene.
Aufgrund des hohen Anteils von ca. 80 Prozent des Individualverkehrs am gesamten Personenverkehr, der abnehmenden Verkehrsräume und der zunehmenden Verkehrsdichte im innerstädtischen Bereich ist es erforderlich, geeignete Verkehrs- und Fahrzeugkonzepte zu entwickeln, um dieses Verkehrsaufkommen zu bewältigen. Die BMW AG hat vor diesem Hintergrund ein neuartiges Zweiradfahrzeug konzipiert. Auf diesem Fahrzeug sitzt der Fahrer aufrecht und angegurtet in einem speziellen Schutzraum, der aus Überrollbügeln gebildet wird. Zusätzlich verfügt das Zweirad im Frontbereich über eine Knautschzone. Da das Fahrzeug bezüglich der passiven Sicherheit über einen hohen Standard verfügt und die Akzeptanz am Markt davon abhängig ist, wird die Möglichkeit untersucht, den Fahrer dieses Fahrzeugs von der Helmtragepflicht zu befreien. Darüber hinaus werden allgemeine Aspekte der aktiven und passiven Sicherheit bewertet. Die Ergebnisse der Untersuchungen sollen es dem Bundesministerium für Verkehr ermöglichen, wissenschaftlich begründete Entscheidungen hinsichtlich der Befreiung von der Helmtragepflicht und den allgemeinen Zulassungsbedingungen zu treffen. Die Untersuchungen basieren auf Messergebnissen und Videoaufzeichnungen von Anprallversuchen, auf Ergebnissen von Computersimulationen, Daten aus Unfallerhebungen, Literaturstudien, Fachgesprächen und weiteren Analysen. Die Sicherheit des C1-Zweirades wurde jeweils für den Frontalanprall, den seitlichen Anprall und die Ausschleuderphase bewertet. Alle Versuchs- und Simulationsdaten ergaben Dummybelastungen, die zeigten, dass das C1-Fahrzeug im Frontalanprall erheblich sicherer ist als ein herkömmliches Zweirad. Auch beim seitlichen Anprall ergibt sich ein Sicherheitsvorteil gegenüber herkömmlichen Zweirädern. Die Ausschleuderphase bei einem Zweiradunfall ist sehr komplex. Soll der Fahrer des C1-Zweirades von der Helmtragepflicht befreit werden, ist sicherzustellen, dass sein Kopf zu keinem Zeitpunkt mit der Fahrbahn oder anderen Hindernissen in Kontakt kommt. Hierzu sind die Sicherheitsrahmenstruktur und das Gurtsystem entsprechend auszulegen. Um das Sicherheitspotential des Zweirades zu bewerten, wurden unter anderem Versuche nach ISO 13232 durchgeführt, in der Unfallkonstellationen zur Beurteilung des Schutzes von Zweiradaufsassen bei Unfällen empfohlen werden. Das Gutachten stellt fest, dass das C1-Zweirad die an die aktive und passive Sicherheit zu stellenden Anforderungen erfüllt. Darüber hinaus kann der Benutzer des Zweirades vorerst von der Helmtragepflicht befreit werden. Die Helmtragepflichtbefreiung ist an die Umsetzung von Sicherheitsanforderungen gekoppelt, die in einem Anforderungskatalog zusammengestellt wurden. In diesem Zusammenhang sind zwei neue Testverfahren entwickelt worden. Aus den Ergebnissen dieses Gutachtens wurden allgemeine Anforderungen für Zweiräder dieser Bauart definiert und eine Ausnahmeverordnung für die Straßenverkehrsordnung (Befreiung von der Helmtragepflicht) vorbereitet. Damit etwaige Probleme frühzeitig erkannt werden, sind nach Markteinführung Unfälle unter Beteiligung des C1-Zweirades sorgfältig zu beobachten und auszuwerten.
During the past five years, a Euro NCAP technical working group on pedestrian safety has been working on improving test and assessment procedures for enhanced passive pedestrian safety. After harmonizing the tools and procedures as much as possible with legislation, the work was mainly focused on the development of grid procedures for the pedestrian body regions head, upper leg with pelvis and lower leg with knee. Furthermore, the test parameters for the head and the upper leg were revised, a new lower legform impactor was introduced and the injury thresholds were adjusted or, where necessary, the injury criteria were changed. Finally, the assessment limits and colour scheme were refined, widening the range and adding two more colours in order to provide a more detailed description of the pedestrian safety performance. By abstaining from an assessment based on a worst point selection philosophy, the improved test point determination procedures that were introduced during the years 2013 and 2014 give a more homogeneous, high resolution picture of the pedestrian safety performance of the vehicle frontends. By using a uniform grid for each test zone approximately 200 test points, evenly distributed within each area, can now be assessed per vehicle. The introduction of the flexible pedestrian legform impactor in 2014 enables a more realistic injury prediction of the knee and the tibia using a biofidelic test tool. With the new upper legform test that has been launched in 2015 the assessment in that area is now focusing on the injured body region instead of the injury causing vehicle part and thus is aligned with the approach in the remaining body regions head and lower leg. At the same time, a monitoring test with the headform impactor against the bonnet leading edge is closing the possible gap between the test areas to identify injury causing vehicle parts that moved out of focus due to the introduction of the new upper legform test. The paper describes the new test and assessment procedures with their underlying philosophy and gives an outlook in terms of open issues, specifying the needs for further improvement in the future. In parallel to the work of the pedestrian subgroup, a Euro NCAP working group on heavy vehicles introduced a set of protocol changes in 2011 that were related to the assessment of M1 vehicles derived from commercial vehicles, with a gross vehicle weight between 2.5 and 3.5 tons and 8 or 9 seats. The paper also investigates the applicability of the new pedestrian test and assessment procedures to heavy vehicles.
The purpose of this paper is to review injuries found in real world lateral collisions and determine the mechanisms responsible for certain kinds of biomechanical failure. During the last years the distribution of deaths among the different types of accidents has changed. Lateral collisions now are the most frequent cause of fatal and other serious injuries. Every third accident is an impact from the side, while every second fatality is the result of a lateral accident. Just a few years ago this value was no higher than 30%. This is probably the result of increasing safety standards for frontal collisions (airbags, seatbelt usage, structural improvements of cars, etc.). Although the number of registered vehicles increased, the total amount of fatalities decreased during the same period. Thus it is now necessary to pay greater attention to the lateral accident situation in order to improve road safety and decrease the number of traffic injuries. Several European organisations had decided to launch the project SID2000, which was funded by the European Commission, with the intention of gathering more knowledge on injuries occurring in lateral accidents and the mechanisms that lead to such injuries. This should enable the group to define the requirements for a new side impact dummy (SID) to be designed. Within the same project the existing TNO-EUROSID 1 was enhanced by another group and the experience gained has now enabled allowed to design a better measuring device for side impacts. The data used for this contribution came from sources from all over Europe and had to be gathered in such a manner that as many accident parameters as possible were taken into account.
Camera-monitor systems (CMS) can be used in motor vehicles to display the driver's rear view on a monitor mounted inside the vehicle. This also offers the possibility of replacing conventional exterior mirrors with suitable CMS and thereby implementing new design concepts with aerodynamic advantages. However, as exterior mirrors are safety-relevant vehicle parts for securing the driver's indirect rear view (requirements specified in UN Regulation No. 46), the question arises whether CMS can provide an equivalent substitute for mirrors. In the scope of this study, CMS and conventional exterior mirrors were compared and assessed in test drives and static tests under different external conditions. On the one hand, the examination of technical aspects, and on the other hand, issues pertaining to the design of the human-machine interaction, were the objects of the study. Two vehicles were available for the trials with passenger vehicles: A vehicle, manufactured in small series, which is already equipped with CMS as sole replacement for the exterior mirrors, as well as a compact class vehicle which had a CMS retrofitted by the car manufacturer in addition to conventionally used exterior mirrors. The latter could be covered exclusively for trips with CMS. A tractor unit with semitrailer was available for the truck trials. The driver's cabin was equipped with a CMS system developed by the vehicle manufacturer. In general, it was shown that it is possible to display the indirect rear view sufficiently for the driver, both for cars and trucks, using CMS which meet specific quality criteria. Depending on the design, it is even possible to receive more information about the rear space from a CMS than is possible with mirror systems. It was also shown that the change from mirrors to CMS requires a certain period of familiarisation. However, this period is relatively short and does not necessarily result in safety-critical situations.
The levels of continuous vehicle automation have become common knowledge. They facilitate overall understanding of the issue. Yet, continuous vehicle automation described therein does not cover "automated driving" as a whole: Functions intervening temporarily in accident-prone situations can obviously not be classified by means of continuous levels. Continuous automation describes the shift in workload from purely human driven vehicles to full automation. Duties of the driver are assigned to the machine as automation levels rise. Emergency braking, e.g., is obviously discontinuous and intensive automation. It cannot be classified under this regime. The resulting absence of visibility of these important functions cannot satisfy " especially in the light of effect they take on traffic safety. Therefore, in order to reach a full picture of vehicle automation, a comprehensive approach is proposed that can map out different characteristics as "Principle of Operation" at top level. On this basis informing and warning functions as well as functions intervening only temporarily in near-accident situations can be described. To reach a complete picture, levels for the discontinuous, temporarily intervening functions are proposed " meant to be the counterpart of the continuous levels already in place. This results in a detailed and independent classification for accident-prone situations. This finally provides for the visibility these important functions deserve.
The 2BeSafe project (2-Wheeler Behaviour and Safety) is a collaborative project (co financed by the European Commission) that aims to study the naturalistic behaviour of Powered-Two-Wheeler (PTW) riders in normal and critical riding situations. That includes the interaction between PTW riders and other road users and possible conflicts between them. One of the predominant causes of accidents involving PTWs is that PTWs are often overlooked by other road users. One task of the project lead by BASt therefore deals with possible improvements in conspicuity and the development of recommendations. Particularly using the findings of the studies on conflict situations, promising lighting arrangements to enhance conspicuity of PTWs during the day and at night are selected. An abstract recognizing pattern for PTWs is defined, enabling other road users (e.g. car drivers) to clearly identify riders. Lamps and outfit like lighting configurations of different colours, different helmet lights, reflect / luminescent clothing parts and retro-reflective markings are designed and manufactured. Then, the different solutions are tested in a laboratory setting using experimental motorcycles together with riders to which the equipment is fitted. As result a proposal for a uniform signal pattern or lamp configuration in the front of all motorcycles and riders will be outlined. The contribution first gives a short overview of the topics of the research project that deal with conflicts and their connection with poor conspicuity and then presents in detail the methods used in the activities concerning solutions for the improvement of conspicuity together with first results.