Filtern
Erscheinungsjahr
Dokumenttyp
- Konferenzveröffentlichung (22)
- Buch (Monographie) (10)
Volltext vorhanden
- ja (32) (entfernen)
Schlagworte
- Anfahrversuch (32) (entfernen)
Institut
Rear-end collisions are the most frequent same and opposite-direction crashes. Common causes include momentary inattention, inadequate speed or inadequate distance. While most rear-end collisions in urban traffic only result in vehicle damage or slight injuries, rear-end collisions outside built-up areas or on motorways usually cause fatal or serious injuries. Driver assistance systems that detect dangerous situations in the longitudinal vehicle direction are therefore an essential safety plus. In view of this, for ADAC, systems that alert drivers to dangerous situations and initiate autonomous braking complement ESC as one of the most important active safety features in modern vehicles. The aim of ADAC is to provide consumers with technical advice and competent information about the systems available on the market. Reliable comparative tests that are based on standardised test criteria may provide motorists with important information and help them make a buying decision. In addition, they raise consumer awareness of the systems and speed up their market penetration. The assessment must focus on as many aspects of effectiveness as possible and include not only autonomous braking but also collision warning and autonomous brake assist. The work of the ADAC accident research is the development of the testing scenarios with direct link to accident situations and the identification of useful test criteria for testing.
Rollovers continue to be a major source of heavy truck fatalities when compared to other accident modes. Real world rollover accidents are analyzed and two distinct damage patterns are identified. Damage to heavy truck roofs can occur from lateral loading that transitions to vertical roof loading as the vehicle rolls onto its side and then over onto its roof. A second load path can occur when the vehicle has rolled onto its side and furrows into the ground generating large longitudinal friction forces between the roof and ground. A review of the previous literature and various test methodologies are presented. A sled impact test methodology is presented which allows for structural assessment of a heavy truck cab's crashworthiness in both of these loading environments. Two test series are presented using the sled impact test methodology in order to analyze real world truck rollovers using varying impact platen and contact angles. The structural deformation and failure patterns were found to be consistent with damage seen in real world accident vehicles. In each case, a second equivalent truck cab was then reinforced and tested under similar conditions to evaluate the energy management and crush resistance of a stronger cab structure. These structural reinforcements demonstrated a substantial reduction in roof crush and protected the survival space of the occupant compartment. The sled impact test procedure is an effective method for testing the structural performance of a heavy truck cab in a variety of loading scenarios comparable to real world accidents and ascertaining the load and energy load levels in these accident modes.
Automotive interiors have long been a potentially injurious impact area to occupants during accidents, especially in the absence of adequate padding. The U.S. Federal Motor Vehicle Safety Standard (FMVSS) 201, Occupant Protection in Interior Impact, outlines test procedures and performance criteria in order to mitigate potentially injurious head impacts to interior surfaces. FMVSS 201 specifies a finite set of impact locations and applies to passenger vehicles of a specified year range and with a gross vehicle weight rating less than 10,000 lb. In this paper, two head impact test methodologies are presented, a pendulum-test device and a Free Motion Headform (FMH) launching device, which allows for dynamic, repeatable impact evaluation of various vehicle interior surfaces and their impact attenuation abilities. The presented testing includes multiple series that evaluate the effect of differing vehicle upper interior padding on occupant head injury. One study in particular, analyzes a head impact to the side header of a heavy truck (not included in FMVSS 201) during a 90 degree rollover. Additionally, two other series of tests are presented which assess the injury reduction effect of side airbags to near side as well as far side occupants in a side impact scenario. Lastly, a forensic analysis is presented which evaluates two possible head impact locations experienced in a real world accident by analysis of the resulting interior compartment damage utilizing the FMH launching device test method. The data collected and presented includes accelerometer instrumentation and high speed video analysis. These studies demonstrate that adequate padding and airbags are very effective at mitigating head injury potential at impact speeds of 12-25 mph (19-40 kph).
A series of drop tests and vehicle tests with the adult head impactor according to Regulation (EC) 631/2009 and drop tests with the phantom head impactor according to UN Regulation No. 43 have been carried out by the German Federal Highway Research Institute (BASt) on behalf of the German Federal Ministry of Transport, Building and Urban Development (BMVBS). Aim of the test series was to study the injury risk for vulnerable road users, especially pedestrians, in case of being impacted by a motor vehicle in a way described within the European Regulations (EC) 78/2009 and (EC) 631/2009. Furthermore, the applicability of the phantom head drop test described in UN Regulation No. 43 for plastic glazing should be investigated. In total, 30 drop tests, thereof 18 with the adult head impactor and 12 with the phantom head impactor, and 49 vehicle tests with the adult head impactor were carried out on panes of laminated safety glass (VSG), polycarbonate (PC) and laminated polycarbonate (L-PC). The influence of parameters such as the particular material properties, test point locations, fixations, ambient conditions (temperature and impact angle) was investigated in detail. In general, higher values of the Head Injury Criterion (HIC) were observed in tests on polycarbonate glazing. As the HIC is the current criterion for the assessment of head injury risk, polycarbonate glazing has to be seen as more injurious in terms of vulnerable road user protection. In addition, the significantly higher rebound of the head observed in tests with polycarbonate glazing is suspected to lead to higher neck loads and may also cause higher injury risks in secondary impacts of vulnerable road users. However, as in all tests with PC glazing no damage of the panes was observed, the risk of skin cut injuries may be expected to be reduced significantly. The performed test series give no indication for the test procedure prescribed in UN Regulation No. 43 as a methodology to approve glass windscreen not being feasible for polycarbonate glazing, as all PC panes tested fulfilled the UN R 43 requirements. The performance of the windscreen area will not be relevant for vehicle type approval according to the upcoming UN Regulation for pedestrian protection. However, it is recommended that pedestrian protection being considered for plastic windscreens to ensure at least the same level of protection as glass windscreens.
Straßenseitige Fahrzeug-Rückhaltesysteme haben entsprechend der Richtlinie für passiven Schutz an Straßen durch Fahrzeug-Rückhaltesysteme (RPS) die Aufgabe, die Folgen von Verkehrsunfällen so gering wie möglich zu halten. Sie kommen dabei sowohl zum Schutz unbeteiligter Personen, des Gegenverkehrs bei zweibahnigen Straßen sowie schutzbedürftiger Bereiche neben der Straße als auch zum Schutz der Fahrzeuginsassen vor schweren Folgen infolge Abkommens von der Fahrbahn zum Einsatz. Vor dem Einsatz der unterschiedlichen Systeme muss die Wirksamkeit des jeweiligen Systems für den entsprechenden Anwendungsfall nachgewiesen werden. Dabei regeln die RPS, welche Anforderungen an welchen örtlichen Gegebenheiten erfüllt sein müssen. In DIN EN 1317 sind die zugehörigen Prüfverfahren beschrieben. Da ein normiertes Prüfverfahren nicht alle real auftretenden Unfallszenarien abdecken kann, stellte sich die Frage, wie sich Stahlschutzplanken und Betonschutzwände beim großwinkligen Anprall kleiner und leichter Fahrzeuge verhalten und wie es um die Insassensicherheit bestellt ist. Eine im Rahmen des resultierenden Forschungsprojektes durchgeführte Analyse des Unfallgeschehens ergab für das Jahr 2007 die Zahl von 25.038 polizeilich registrierten Unfällen mit Anprall gegen eine Schutzeinrichtung [Statistisches Bundesamt]. Angaben zu Anprallwinkel, Kollisionsgeschwindigkeit und Fahrzeugmasse können dieser Statistik nicht entnommen werden. Für die In-depth-Analyse wurden daher 69 Unfallgutachten zu Kollisionen mit großem Anprallwinkel (≥ 25-°) aus der DEKRA-Unfalldatenbank herangezogen. Der Schwerpunkt wurde dabei auf 39 Unfälle gelegt, die sich auf Bundesautobahnen ereignet hatten. Mit zunehmendem Anprallwinkel nahm die Unfallhäufigkeit ab. Der größte Winkel lag bei 60-°. Die Masse der anprallenden Fahrzeuge lag zwischen 750 kg und 1.935 kg. Auffällig war die Häufung von Schleuderunfällen. In 29 Fällen kam es zu einem prekollisionären Schleudervorgang. Die Analyse des Unfallgeschehens hat so gezeigt, dass Anpralle gegen passive Schutzeinrichtungen auf Bundesautobahnen mit zunehmendem Anprallwinkel seltener werden und dass der in der Norm für die Systemprüfung geforderte Maximalwinkel von 20-° das Gesamtunfallgeschehen sehr gut abdeckt. Auf Basis der gewonnenen Ergebnisse erfolgte die Festlegung einer Crash-Test-Konfiguration zur Erlangung von Erkenntnissen über die Insassensicherheit bei großwinkligen Anprallen. Dabei wurde als Grundlage der Anprallversuch TB 11 verwendet, wobei der Anprallwinkel von 20-° auf 45-° erhöht wurde. Die Kollisionsgeschwindigkeit von 100 km/h sowie die Fahrzeugmasse von 900 kg blieben unverändert. Die Anpralltests erfolgten gegen eine simulierte Ortbetonwand sowie gegen eine Stahlschutzplanke vom Typ Super-Rail-®. Die Versuchsfahrzeuge waren typgleich mit den Modellen, die für die ursprüngliche TB-11-Prüfung der Systeme verwendet wurden. Die Versuche haben gezeigt, dass beide Systeme die Rückhaltung der anprallenden Fahrzeuge sicher gewährleisteten. Für die Fahrer beider Fahrzeuge hätte aber keine Überlebenschance bestanden. Über das Schutzniveau der Fahrzeuginsassen entscheiden bei derartigen Anprallkonstellationen letztendlich das Niveau der passiven Sicherheit der anprallenden Fahrzeuge sowie das Energieabsorptionsvermögen der die Fahrgastzelle umschließenden Strukturen.
Over the past two decades the popularity of consumer crash test programs, commonly referred to as New Car Assessment Programs (NCAP), has grown across the world. They are popular among government regulators as they afford a means of promoting safety innovations and levels of vehicle performance beyond those dictated by national standards. They also fulfill the demand for information regarding the safety ranking of vehicles among consumers contemplating the purchase of a new vehicle. There is no question that consumer crash test programs greatly influence vehicle design changes as well as accelerate the fitment of new safety features. The extent to which these changes can be expected to reduce serious and potentially fatal injuries will be influenced by how well the testing protocols and associated rating schemes correctly reflect the nature of the residual safety problem they seek to address. Drawing on data contained primarily in the US National Automotive Sampling System (NASS), the field relevance of current and proposed testing and rating protocols addressing frontal crash test protection is examined. Emphasis is placed on examining how accurately injury rates computed from the dummy responses measured in consumer crash tests correspond to actual injury rates observed in the field. Additional data from Canadian field investigations and US databases such as the National Motor Vehicle Crash Causation Survey (NMVCCS) are examined to see how well frontal airbag firing times, crush pulse durations and other determinants of injury are replicated in consumer testing protocols. This portion of the analysis draws on data obtained from Event Data Recorders (EDR) in both field collisions and staged tests of the same vehicle model. Vehicle rankings and overall frontal crash test ratings were found to be particularly sensitive to the choice of injury risk functions employed in the test. This was particularly true in the case of injury risk functions used to assess neck injury potential. Neck injury risk derived from Nij was found to show the least agreement with the field. Agreement between field chest injury rates and those derived from crash tests was improved considerably when chest injury risk functions for "older" occupants were employed. The paper concludes with a discussion of how different current testing protocols could be improved to enhance their field relevance.
Females sustain Cervical Spine Distortion injury (CSD) more often than males. Most work dealing with the biomechanics background (e.g. injury mechanism/criteria) as well as the application in seat design/testing, focuses on the occupant model of an average male. Therefore the EU-Project ADSEAT (Adaptive Seat to Reduce Neck Injuries for Female and Male Occupants) is aimed at adding a female model for gender balanced research of CSD and improving seat design. An extensive literature review, searching for risk factors and injury criteria for males and females, was accompanied by the evaluation of different databases containing CSD cases. The database evaluations suggests that an anthropometry quite close to the 50%ile female anthropometry as known from crash test dummy design is appropriate. The results presented here form the basis for the future development of a computational female model and the improvement of seat design for better protection of both males and females in the frame of the ADSEAT-Project.
Werden die in Deutschland gebräuchlichen Stahlschutzplanken umgestaltet um das Verletzungsrisiko für Motorradfahrer zu verringern, zeigt sich ein Kompatibilitätsproblem: Die Erhöhung der Sicherheit für Motorradfahrer wird mit Einschränkungen der Sicherheit von Pkw-Insassen erkauft. Um dieses Kompatibilitätsproblem zu lösen wurden unter Federführung der Bundesanstalt für Straßenwesen (BASt) neue Nachrüstkomponenten für Stahlschutzplanken entwickelt. Dabei lag der Schwerpunkt auf der Senkung der Verletzungsschwere für Motorradfahrer. Im vorliegenden Projekt sollten die Nachrüstkomponenten des Systems "EuskirchenPlus" ihre Tauglichkeit auch für Pkw-Insassen in Anprallprüfungen (Crashtests) beweisen. Dies gelang zunächst nicht. Daher wurden die Nachrüstkomponenten zu neuen Konstruktionen ("ESP-Motorrad" und "EDSP-Motorrad") weiterentwickelt, und es gelang, die "ESP-Motorrad" erfolgreich zu prüfen. Die Eignung der "EDSP-Motorrad" wurde aus den vorliegenden Forschungsergebnissen und den Erfahrungen der BASt abgeleitet. Das Kompatibilitätsproblem konnte zwar nicht umfassend gelöst, jedoch soweit beseitigt werden, dass keine relevanten Einsatzbeschränkungen mehr aufrecht erhalten werden müssen. Die "ESP-Motorrad" und die "EDSP-Motorrad" sind auf nahezu allen für Motorradunfälle relevanten Strecken grundsätzlich geeignet, die klassischen Stahlschutzplanken ESP beziehungsweise EDSP zu ersetzen.
Accidents involving two wheels vehicles represent one of the more important types of accidents in Europe. These accidents are usually not easy to reconstruct specially for the analysis of the injuries and its correlation with accident dynamics and evidences. Different methodologies are applied in this work for the reconstruction of two wheeler accidents, especially accident involving motorcycles. From the typologies of road evidences like skid marks, to the use of Pc-Crash and the use of Madymo models, different reconstruction of real accidents are presented. One of the questions that sometimes arise for legal purposes when some type of head injuries arise is if the occupant was wearing or not a helmet. The correlation of head injuries with the use of the helmet is a very important issue, therefore an important legal aspect. One of the key questions for the reconstructions that is difficult to analyze, is if the vehicle occupant, was or not, wearing the helmet. Based on the previously collected information, a generic model of a helmet was developed on CAD 3D, followed by its conversion into finite elements, all in order to perform impact tests using the Madymo software that would help improve the helmet- safety, but that also can be used as a tool in accident reconstruction.
Event Data Recorder (EDR) is an additional function installed in airbag control module (ACM) to record vehicle and occupant information for a brief period of time before, during, and after a crash event. EDRs are now being installed in ACMs by several automakers in the USA and in Japan. The aim of this study is to understand the performance of EDRs for the improvement of accident reconstruction with more reliable information. In the first report of the study, data obtained from EDRs of seven vehicle types were evaluated using 2006-2007 J-NCAP (Japanese new car assessment program) full-lap frontal barrier crash tests and offset frontal deformable barrier crash tests data. For more practical standpoint, we conducted thirteen crash tests reconstructing typical real-world accidents such as single vehicle accidents with barriers or poles, car to car accidents and multi rear-end collisions focusing on Japanese typical accident types. Data obtained from EDRs are compared with data obtained from optical speed sensor, instrumented accelerometers and high speed video cameras. The velocities determined from pre-crash data of EDRs and the maximum change in velocity, delta-V, and delta-V time history data obtained from post-crash data of EDRs are analyzed. The results are as follows: - Pre-crash velocities of EDRs were very accurate and reliable. An average difference between the EDR recording values and reference speeds was 4.2% and a root mean square of the differences was 9.2%. Only two cases resulted large differences for the pre-crash velocity. Both of them were cases with braking prior to the collision. However, another test with braking resulted less difference. The braking condition may influence accuracy of pre-crash velocities. - Maximum delta-Vs obtained from the EDRs showed uncertainty of measurement in several cases in comparisons with the reliable delta-V data. The differences in maximum delta-V were more than 10% in five of twenty-five events data and more than 20% in two of twenty-five events data. An average of the all differences was about 4% and root mean square of the differences was about 11%. Especially large deformation at narrow area may influence accuracy of post-crash delta-V. - Multiple rear-end crash tests were reconstructed using EDRs data as case studies. Some EDRs recorded two events and a time gap between two events, so that these reconstruction case studies were very accurate and reliable. - If though only one of three vehicles in multiple rear end crash was equipped EDR, overview and velocities of all cars may be reconstructed using these limited EDR data. In this case study, leading car- EDR data and middle car- EDR data were valuable. However if only following car was equipped EDR, the reconstruction was not accurate