Der Anteil von Geländefahrzeugen an der Gesamtzahl von Personenkraftwagen betrug im Juli 1991 in den alten Bundesländern ca. 1,1 Prozent. Nach eigenen Erhebungen sind etwa 62 Prozent der Geländefahrzeuge mit einem Frontschutzbügel ausgestattet. Der Bundesminister für Verkehr hat die BASt beauftragt zu prüfen, ob solche Konstruktionen einen Einfluss auf die Verletzungen bei Kollisionen mit Fußgängern und Zweiradbenutzern haben. Dazu wurde das Datenmaterial der Unfallerhebung der Medizinischen Hochschule Hannover ausgewertet und die um fahrzeugtechnische Angaben ergänzten Unfalldaten aus Nordrhein-Westfalen betrachtet. Weiterhin wird von Komponententests berichtet, die den Anprall menschlicher Körperteile an das Fahrzeug simulieren. Mit den Ergebnissen dieser Untersuchung wurde ein Frontschutzbügel hergestellt, der weniger aggressiv gegenüber ungeschützten Verkehrsteilnehmern ist. Zur Quantifizierung der Gefährdung von Fußgängern wurden zwei gängige Geländefahrzeugtypen mit und ohne Frontschutzbügel gemäß dem Prüfvorschlag der EEVC-WG 10 zur Bestimmung der Fußgängerverträglichkeit von Pkw-Frontflächen getestet. Die Ergebnisse aus den Versuchsreihen wurden mit Ergebnissen aus Versuchen an normalen Pkw verglichen.Es kann festgestellt werden, dass bei einem Unfall mit Kopfanprall eines Kindes an ein mit Frontschutzbügel ausgestattetes Geländefahrzeug bei 20 km/h mit gleichen Kopfbelastungen zu rechnen ist, wie bei einem Unfall mit 30 km/h mit einem Geländefahrzeug ohne Frontschutzbügel, beziehungsweise mit 40 km/h mit einem normalen Pkw. Für den Hüftanprall eines Erwachsenen an die Haubenkante ist bei einer Fahrzeuggeschwindigkeit von 25 km/h bei einem Fahrzeug mit Frontschutzbügel mit gleichen Belastungen zu rechnen, wie bei einem Unfall mit einem Fahrzeug ohne Frontschutzbügel bei 40 km/h (Pkw oder Geländewagen). Für die Belastungen des Knies eines Erwachsenen lässt sich keine Verschlechterung durch montierte Frontschutzbügel ableiten.
Der Nutzen des Schutzhelmes für motorisierte Zweiradfahrer ist unumstritten. Die Grenzwerte für eine zulässige Kopfbeschleunigung bei der Prüfung des Dämpfungsverhaltens gemäß ECE-R 22 sind jedoch weiterhin in der Diskussion. In der vorliegenden Untersuchung wird deshalb die Kopfbelastung eines Dummys beim Pkw-Crash-Versuch mit den Belastungen des behelmten Prüfkopfes bei Fallversuchen gemäß ECE-R 22 verglichen. Bei den durchgeführten Fallversuchen besteht ein enger Zusammenhang zwischen HIC und maximaler Beschleunigung, der durch eine analytische Funktion beschrieben werden kann. Es kann gezeigt werden, dass die bei ECE-R 22 zulässige Kopfbeschleunigung von 300 g einem HIC von etwa 3400 entspricht. Zur Bewertung von Schutzhelmen mit verbesserten Stoßabsorptionseigenschaften erscheint es sinnvoll, wie anhand von Modellrechnungen gezeigt wird, den HIC als Schutzkriterium einzuführen. Bei einer Anprallgeschwindigkeit von 7 m/s kann ein HIC von 1500 als realistische Forderung angesehen werden, sofern bei der ECE-Regelung der sogenannte Zweitschlag entfällt. Bei den Pkw-Versuchen ist kein Zusammenhang zwischen HIC und maximaler Beschleunigung vorhanden. Hier ist der HIC als Verletzungskriterium etabliert, und das ist für den komplexen Verlauf des Signals der Kopfbeschleunigung sinnvoll. Eine Bewertung nach anderen Kopfschutzkriterien würde die Rangfolge der einzelnen Versuche ändern. Bei Helmversuchen auf den Stirnanprallpunkt B werden starke Rotationen des rückprallenden Systems Prüfkopf/Helm beobachtet. In Verbindung damit treten hohe Rotationsbeschleunigungen auf. Diese liegen, wie bei einem Teil der Helmversuche gemessen, zwischen 2,4 und 4,8 krad/s2.
A biofidelic flexible pedestrian legform impactor (FlexPLI) has been developed from the year 2000 onwards and evaluated by a technical evaluation group (Flex-TEG) of UN-ECE GRSP. A recently established UN-ECE GRSP Informal Group on GTR9 Phase 2 is aiming at introducing the FlexPLI within world-wide regulations on pedestrian safety (Phase 2 of GTR No. 9 as well as the new UN regulation 127 on pedestrian safety) as a test tool for the assessment of lower extremity injuries in lateral vehicle-to-pedestrian accidents. Besides, the FlexPLI has already been introduced within JNCAP and is on the Euro NCAP roadmap for 2014. Despite of the biofidelic properties in the knee and tibia sections, several open issues related to the FlexPLI, like the estimation of the cost benefit, the feasibility of vehicle compliance with the threshold values, the robustness of the impactor and of the test results, the comparability between prototype and production level and the finalization of certification corridors still needed to be solved. Furthermore, discussions with stakeholders about a harmonized lower legform to bumper test area are still going on. This paper describes several studies carried out by the Federal Highway Research Institute (BASt) regarding the benefit due to the introduction of the FlexPLI within legislation for type approval, the robustness of test results, the establishment of new assembly certification corridors and a proposal for a harmonized legform to bumper test area. Furthermore, a report on vehicle tests that previously had been carried out with three prototype legforms and were now being repeated using legforms with serial production status, is given. Finally, the paper gives a status report on the ongoing simulation and testing activities with respect to the development and evaluation of an improved test procedure with upper body mass for assessing pedestrian femur injuries.
A legform impactor with biofidelic characteristics (FlexPLI) which is being developed by the Japanese Automobile Research Institute (JARI) is being considered as a test tool for legislation within a proposed Global Technical Regulation on pedestrian protection (UNECE, 2006) and therefore being evaluated by the Technical Evaluation Group (TEG) of GRSP. In previous built levels it already showed good test results on real cars as well as under idealised test conditions but also revealed further need for improvement. A research study at the Federal Highway Research Institute (BASt) deals with the question on how leg injury risks of modern car fronts can be revealed, reflected and assessed by the FlexPLI and how the impactor can be used and implemented as a legislative instrument for the type approval of cars according to current and future legislations on pedestrian protection. The latest impactor built level (GTα ) is being evaluated by a general review and assessment of the certification procedure, the knee joint biofidelity and the currently proposed injury criteria. Furthermore, the usability, robustness and durability as a test tool for legislation is examined and an assessment of leg injuries is made by a series of tests with the FlexPLI on real cars with modern car front shapes as well as under idealised test conditions. Finally, a comparison is made between the FlexPLI and the current european legislation tool, the legform impactor according to EEVC WG 17.
A flexible pedestrian legform impactor (FlexPLI) with biofidelic characteristics is aimed to be implemented within global legislation on pedestrian protection. Therefore, it is being evaluated by a technical evaluation group (Flex-TEG) of GRSP with respect to its biofidelity, robustness, durability, usability and protection level (Zander, 2008). Previous studies at the Federal Highway Research Institute (BASt) and other laboratories already showed good progress concerning the general development, but also the need for further improvement and further research in various areas. An overview is provided of the different levels of development and all kinds of evaluation activities of the Flex-TEG, starting with the Polar II full scale pedestrian dummy as its origin and ending up with the latest legform impactor built level GTR that is expected to be finalized by the end of the year 2009. Using the latest built levels as a basis, gaps are revealed that should be closed by future developments, like the usage of an upper body mass (UBM), the validation of the femur loads, injury risk functions for the cruciate knee ligaments and an appropriate certification method. A recent study on an additional upper body mass being applied for the first time to the Flex-GT is used as means of validation of recently proposed modified impact conditions. Therefore, two test series on a modern vehicle front using an impactor with and without upper body mass are compared. A test series with the Flex-GTR will be used to study both the comparability of the impact behavior of the GT and GTR built level as well as the consistency of test results. Recommendations for implementation within legislation on pedestrian protection are made.
A flexible pedestrian legform impactor (FlexPLI) has been evaluated by a Technical Evaluation Group (Flex-TEG) of the Working Party on Passive Safety (GRSP) of the United Nations Economic Commission for Europe (UN-ECE). It will be implemented within phase 2 of the global technical regulation (GTR 9) as well as within a new ECE regulation on pedestrian safety as a test tool for the assessment of lower extremity injuries in lateral vehicle-to-pedestrian accidents (UN-ECE 2010-1, 2010-2 and 2010-3). Due to its biofidelic properties in the knee and tibia section, the FlexPLI is found to having an improved knee and tibia injury assessment ability when being compared to the current legislative test tool, the lower legform impactor developed by the Pedestrian Safety Working Group of the European Enhanced Vehicle-safety Committee (EEVC WG 17). However, due to a lack of biofidelity in terms of kinematics and loadings in the femur part of the FlexPLI, an appropriate assessment of femur injuries is still outstanding. The study described in this paper is aimed to close this gap. Impactor tests with the FlexPLI at different impact heights on three vehicle frontends with Sedan, SUV and FFV shape are performed and compared to tests with a modified FlexPLI with upper body mass. Full scale validation tests using a modified crash test dummy with attached FlexPLI that are carried out for the first time prove the more humanlike responses of the femur section with applied upper body mass. Apart from that they also show that the impact conditions described in the current technical provisions for tests with the FlexPLI don"t necessarily compensate the missing torso mass in terms of knee and tibia loadings either. Therefore it can be concluded that an applied upper body mass will contribute to a more biofidelic overall behavior of the legform and subsequently an improved injury assessment ability of all lower extremity injuries addressed by the FlexPLI. Nevertheless, the validity of the original as well as the modified legform for tests against vehicles with extraordinary high bumpers as well as flat front vehicles still needs to be evaluated in detail. A first clue is given by the application of an additional accelerometer to the legform.
Ziel dieser Arbeit war die Entwicklung eines numerischen Modells des menschlichen knöchernen Thorax, das insbesondere altersabhängige geometrische Faktoren berücksichtigt. Dieses Modell soll sowohl die männliche als auch die weibliche Population der über 64-Jährigen repräsentieren und eine an diese Altersgruppe angepasste Verletzungssimulation ermöglichen. Die vorliegende Studie identifiziert zunächst an Hand eines Kollektivs aus 126 postmortem und 40 klinischen computertomografischen Schnittbildaufnahmen eine ganze Reihe geometrischer Parameter, die sich mit dem Alter verändern. Zu den untersuchten Parametern gehören sowohl Winkel der Rippen im Raum und innerhalb des Rippenbogens, eine detaillierte Erfassung von Parametern der einzelnen Rippe (Querschnittsfläche, Krümmung, Longitudinale Verdrillung), Parameter der Wirbelsäule als Ganzes (Skoliose, Kyphose, Rotation) und einzelner Wirbel sowie des Brustbeins. Weiterhin wurden die Grundmasse des ganzen Thorax (Thoraxtiefe, Thoraxbreite) untersucht. Die hier gefundenen Altersabhängigkeiten dienten als Eingabeparameter zur Erstellung von insgesamt neun aus dem Menschmodell THUMS 3 gemorphter alter und junger Finite-Elemente Thoraxmodelle. Implementiert wurden hierbei sowohl Durchschnittsmaße als auch extreme Maße. Die Ergebnisse zeigen mehrere sich im Alter signifikant verändernde Parameter. Als wichtigste unter ihnen sind eine Zunahme der Thoraxtiefe und Thoraxbreite im Alter, die signifikante Veränderung einiger Rippenwinkel im Raum sowie der Krümmung der sechsten und siebten Rippe zu nennen. Zudem wird die Wirbelsäulenform kyphotischer und das Sternum am Übergang zwischen Manubrium und Corpus sternii gewinkelter. Die Menschmodelle THUMS 3, THUMS 4 und HUMOS 2 sind weder als typisch alt, noch typisch jung einzuordnen, dies unterscheidet sich teils von Parameter zu Parameter. Die auf Basis der Geometrie-Inputdaten durchgeführten Finite-Elemente Simulationen zeigen einen deutlichen Einfluss der zunehmenden Thoraxtiefe im Alter auf die posteriore Kraft an der Auflagefläche der Rippen sowie die Spannungsverteilung entlang der Rippen. Sie wirkt sich jedoch entgegen der Erwartungen protektiv aus und dominiert andere Faktoren wie die unterschiedlichen Rippenwinkel. Abschließend betrachtet wird ein Menschmodell, welches das 75. Perzentil der alten Bevölkerung repräsentiert, als ausreichend aussagekräftig hinsichtlich der im Alter veränderten Geometrie klassifiziert und gleichzeitig als mit angemessenem Aufwand realisierbar angesehen. Es wird daher für die Bewertung von Sicherheitssystemen empfohlen.
The PDB, BASt and Opel conducted two test series to evaluate possible effects on the results obtained using the EEVC WG17 Lower Legform Impactor as a test tool for the assessment of pedestrian safety. The reproducibility and repeatability of the test results were assessed using six legform impactors while keeping the test parameters constant. In the second series one impactor was used and the test parameters were varied to assess the effects on the readings of the legform. The test parameters were velocity, temperature, relative humidity, the point of first contact regarding the deviation in z-direction and the deviations of the pitch, roll and yaw angle. The tests were performed using an inverse setup, i.e. the legform was hit by a guided linear impactor equipped with a honeycomb deformation element. This setup was chosen to be able to vary each single parameter while avoiding variations of the other test parameters at the same time. The test parameters were varied stronger than allowed in regulatory use in order to determine possible dependencies between the parameters and the readings which were acceleration, bending angle and shear displacement.
Real world accident reconstruction with the Total Human Model for Safety (THUMS) in Pam-Crash
(2013)
Further improvement of vehicle safety needs detailed analysis of real world accidents. According to GIDAS (German In-Depth Accident Study) most car to car front accidents occur at mid-crash severity. In this range thoracic injuries already occur. In this study a real world frontal crash with mid-crash severity out of the AARU database was reconstructed. The selected car to car accident was reconstructed by AARU by means of pc-crash software in order to get the initial dynamic accident conditions. These initial conditions were used to reconstruct the complete accident in more detail using FE models for the car structure and the occupants. Occupant simulations were performed with FE HIII-dummy models and the THUMS using Pam-Crash code. An initial THUMS validation was performed in order to verify the model-´s biofidelity by means of table-top test simulations. THUMS bone stiffness values were modified to match the real word occupant age. A comparison between driver and passenger restraint system loading was done, as well as an injury prediction comparison between the HIII-dummy model and THUMS response for both cases. Detailed comparison between the HIII-dummy models and THUMS regarding thoracic loading are discussed.
Females sustain Cervical Spine Distortion injury (CSD) more often than males. Most work dealing with the biomechanics background (e.g. injury mechanism/criteria) as well as the application in seat design/testing, focuses on the occupant model of an average male. Therefore the EU-Project ADSEAT (Adaptive Seat to Reduce Neck Injuries for Female and Male Occupants) is aimed at adding a female model for gender balanced research of CSD and improving seat design. An extensive literature review, searching for risk factors and injury criteria for males and females, was accompanied by the evaluation of different databases containing CSD cases. The database evaluations suggests that an anthropometry quite close to the 50%ile female anthropometry as known from crash test dummy design is appropriate. The results presented here form the basis for the future development of a computational female model and the improvement of seat design for better protection of both males and females in the frame of the ADSEAT-Project.