Mobility is a central requirement for economic growth, employment and participation of each individual in social life. This basic principle of the BMVI (Federal Ministry of Transport and Digital Infrastructure) requires an intact and functional infrastructure. In a context of increasing investments over the next few years, it will be relevant to develop a network related systematic procedure to be part of the structural maintenance of the federal highway network. In the planning of maintenance measures, the knowledge about the state of structural performance and its long-term development is of central importance. In the following, a method is presented which allows the mechanically and statistically reliable assessment and prognosis of structural performance of concrete pavements. In addition, the application and procedure are applied to a case study.
In Germany, expenditure for the construction of new and maintenance of existing federal highways is currently at a record level of EUR 8 billion per year. In connection with the planned infrastructure policy reforms it is necessary to further develop the planning tools for dimensioning and substance assessment of road structures in order to increase the efficiency of construction measures. The stress caused by traffic is of central importance here. Since unevenness in the road surface has a significant influence on the dynamic part of the wheel load, dynamic effects must be explicitly taken into account. As a result, increasing unevenness can lead to higher dynamic loads and, in the context of a corresponding number of wheel rollovers, to disproportionate damage to the road structure. In general, a shock factor is taken into account during dimensioning, which is to be considered as a function of vehicle suspension, load, speed and evenness. This approach is not sufficient for concrete road structures executed as slabs. In the normal case, only the periodically occurring individual event of a transverse contraction joint, superimposed by irreversible and/or temporary slab deformations, can lead to a significant increase in the dynamic wheel load. In addition, the existing slab deformations are tied to many boundary conditions and can therefore vary greatly in their characteristics. For the further development of methods for dimensioning and residual substance assessment with regard to their accuracy, a three-dimensional slab-specific view of the road surface is therefore appropriate. In this paper, a suitable measuring method for three-dimensional surface laser scanning and an algorithm for the classification of slab deformations are presented.
The Netherlands is on the way to change its existing skid resistance measuring method for its highway network from the Dutch RAW 72, a longitudinal force method, to the Sideway Force method. This method is described in the Technical Specification 15901-8 (SKM device) as well as 15901-6 (SCRIM device) and is in use in 9 European countries. The CEN TC 227 WG5 on Surface Characteristics is currently working on combining of these two technical Specifications into a European standard for Sideway-Force (SWF) measurement devices. The idea of this change in the Netherlands was perceived in 2013 and since then a lot of meetings have been held with the different Dutch decision makers as well as with countries which currently operate SWF devices. There was an intensive exchange of knowledge about these devices and their corresponding quality assurance systems, because the Netherlands wanted to incorporate and rely on an existing system of a neighbor country without losing their present level of quality. The Netherlands has therefore decided to incorporate the German SKM approach. The network monitoring with the new system will start in 2017. To ensure the quality of skid resistance measurements and further cooperation in this field, it has been decided to initiate an alliance between BASt and the Dutch road owner Rijkswaterstaat (RWS). This alliance will facilitate an exchange of research activities, calibration of the Dutch systems according to the existing German Standard as well as control measurements with a BASt-device on the Dutch network during the network monitoring. During 2016 also comparative measurements will be performed on a network level with the current Dutch device and with an SKM device to determine a conversion between the two and to be able to define new threshold values.
Measuring and characterizing airborne particulate matter (PM) is an important research area because PM can lead to impacts on health and to visibility reduction, material damage and groundwater pollution. In regard to road dust, suspension and re-suspension and the contribution of non-exhaust PM to total traffic emissions are expected to increase as a result of predicted climate scenarios. European environmental regulations have been enforced to reduce exhaust particle emissions from road traffic, but little attention has been paid to reducing non-exhaust coarse particle emissions due to traffic. Therefore, a monitoring program for coarse PM has been initiated in early 2013 to assess the predicted increase in the abundance of non-exhaust particles. Particle sampling was performed with the passive-sampler technique Sigma-2. The subsequent single-particle analysis allows for characterization of individual particles, determination of PM size distribution, and calculation of PM mass concentrations. Two motorways n ear Cologne (Koeln), Germany were selected as sampling sites, and the experimental setup in the field was realized with a so-called twin-site method. The present study reports single-particle analysis data for samples collected between May 31, 2013 and May 30, 2014. Coarse PM, generated through multi-source mechanisms, consists of, e.g., tire-wear, soot aggregates, and mineral dust. The highest mass concentration occurs at both motorways in spring, and the observed PM mainly contains traffic-abrasion particles. The field measurements show that the minimum PM concentration was found in the 5 to 12-°C temperature range, whereas the maximum concentration was observed in both the "5 to 5-°C and the 12 to 24-°C ranges, in agreement with previous laboratory measurements. Correlation between super-coarse (d p 10"80 μm, geometric equivalent diameter) PM concentration and precipitation displays a significant increase in concentration with decreasing number of precipitation events (dry weather periods).
As the data for road weather stations is used for online traffic control within section control systems, it is very important for the efficiency of the traffic control systems to be based on reliable data of a high quality. Therefore, a Test Site for checking the quality of road weather stations was established near Munich in Germany in 2003 and has been operational since then. In close co-operation with all participants (sensor manufacturers, road authorities, German Federal Research Institute, research and consultancy bodies), the overall goal was to improve the sensors" quality as well as to establish methods to detect failures in measurements. Furthermore, several improvements were carried out within the scope of the Test Site using the expertise of all participants and the infrastructure of the Test Site. The developments, reports and results obtained are both significant and helpful for manufacturers, road authorities, practitioners, research and consultancy.
In the framework of the OECD study "Moving Freight with Better Trucks", several vehicle combinations which are worldwide in operation were examined regarding different performance criteria. One criterion was the road wear performance of these articulated vehicles. With given tyre and vehicle data (mainly weights and axle loads) the road wear performance was calculated for each vehicle combination. The method according to COST 334 is presented and the vehicle combinations are compared