Filtern
Erscheinungsjahr
- 2014 (4) (entfernen)
Dokumenttyp
Schlagworte
- Norm (tech) (4) (entfernen)
Institut
Structured road markings are becoming popular as edge line on high speed roads, ensuring night time visibility (retroreflection) during rain. These markings are often also "audio-tactile": vehicles (un)intentionally driving over it may produce much more tyre/road sound, which may be observed in the vehicle but also in the vicinity. The sound increase inside the car can be considered as a positive side effect, as it alarms the driver and may be very helpful for the prevention of "doze off" traffic accidents. The sound increase perceived outside the car however, may have a positive aspect as it can warn people on the emergency lane about the approaching vehicle, but it may as well annoy people living around. A method for the assessment of the acoustic properties of audio-tactile markings has been developed. It is mainly based on the "Close Proximity" (CPX) method, an ISO method intended for the acoustic assessment of pavements. The results of measurement campaigns with CPX trailers in Belgium and Germany according to a specially designed procedure are presented. The feasibility of the method is discussed. The research has been carried out in the frame of the standardization activities of the CEN working group CEN/TC226/WG2 "Horizontal signalization".
In Europe, in situ measurements of sound reflection and airborne sound insulation of noise barriers are usually done according to CEN/TS 1793-5. This method has been improved substantially during the EU funded QUIESST collaborative project. Within the same framework, an inter-laboratory test has been carried out to assess the repeatability and reproducibility of the newly developed method when applied to real-life samples, including the effect of outdoor weather variability and sample ageing. This article presents the statistical analysis of the inter-laboratory test results, and the values of the repeatability and the reproducibility, both in one-third octave bands and for the single-number ratings. The estimated reproducibility values can be used as the extended measure of uncertainty at the 95% credibility level in compliance with the ISO GUM. The repeatability and reproducibility values associated with airborne sound insulation are also compared with the corresponding values for laboratory measurements in building acoustics and an acceptable agreement is found.
The paper describes the development of transitions between different safety barriers in Germany but also in the context of the European standardization. In the paper practical and impact test expriences with transitions are shown. In view of the sheer number of theoretically possible combinations of safety barriers, the demand for testing every transition, even if the connecting safety barriers differ only slightly, appears to be economically unacceptable. On the other hand the experience from accidents and also from failed impact tests shows that transitions can be a risk to traffic safety. Therefore criteria for the distinction between transitions (impact test required/impact test unnecessary) are explained. In order to distinguish transitions which do not have to be impact-tested from those that require impact tests, criteria were developed and formulated.
Fahrerassistenzsystemen mit Umfeldwahrnehmung wird ein hohes Potenzial zur Unfallvermeidung zugeschrieben, wenn diese umfassender und intensiver in die Fahrdynamik von Fahrzeugen eingreifen und weiter vernetzt werden. Diese erweiterten Eingriffsmöglichkeiten erzeugen auch neue Risiken, welche vor der Genehmigung und Zulassung für den öffentlichen Straßenverkehr abgesichert werden müssen. Neuartig ist bei diesen Systemen, dass sie nur über eine Situationsrepräsentation die unfallvermeidenden Handlungen ableiten können. Somit kommt zum Risiko des Versagens von Systemkomponenten, das bereits durch die ISO 26262-Norm zur funktionalen Sicherheit adressiert ist, das Risiko aufgrund einer falschen Interpretation auftretenden, nicht situationsgemaessen Auslösung, z. B. durch Situationskonstellationen, die bei der Entwicklung nicht berücksichtigt wurden und daher in den Funktionsspezifikationen nicht enthalten sind. Um die Anforderungen an Absicherungsmethoden für diese Assistenzsysteme zu identifizieren, werden diese zusammengestellt und der Absicherungsaufwand mit bestehenden Methoden, bspw. aufbauend auf den Anforderungen der ISO 26262, bestimmt. Die Analyse zeigt, dass bisherige Ansätze sowohl hinsichtlich der objektiven Nachweisbarkeit der Vollständigkeit der theoretisch möglichen Situationen Lücken aufweisen als auch hinsichtlich des Umfangs der notwendigen Spezifikationen und deren Prüfung in Versuchen. Aufgrund des daher zu erwartenden Aufwands für den Nachweis eines sicheren Verhaltens der Systeme sind eine Priorisierung von Fahrsituationen und die Gewährleistung einer hohen Übertragbarkeit von Bewertungsergebnissen notwendig. Um die Vollständigkeitsproblematik zu adressieren, wird ein Ansatz vorgestellt, der eine objektive Bewertung und den Vergleich von Fahrsituationen ermöglicht. Abschließend werden die Erkenntnisse zusammengefasst und notwendige weitere Schritte für die Schaffung einer einheitlichen Absicherungsstrategie für Fahrerassistenzsysteme abgeleitet.