Filtern
Erscheinungsjahr
Dokumenttyp
Sprache
- Englisch (20) (entfernen)
Schlagworte
- Messung (20) (entfernen)
Institut
The Netherlands is on the way to change its existing skid resistance measuring method for its highway network from the Dutch RAW 72, a longitudinal force method, to the Sideway Force method. This method is described in the Technical Specification 15901-8 (SKM device) as well as 15901-6 (SCRIM device) and is in use in 9 European countries. The CEN TC 227 WG5 on Surface Characteristics is currently working on combining of these two technical Specifications into a European standard for Sideway-Force (SWF) measurement devices. The idea of this change in the Netherlands was perceived in 2013 and since then a lot of meetings have been held with the different Dutch decision makers as well as with countries which currently operate SWF devices. There was an intensive exchange of knowledge about these devices and their corresponding quality assurance systems, because the Netherlands wanted to incorporate and rely on an existing system of a neighbor country without losing their present level of quality. The Netherlands has therefore decided to incorporate the German SKM approach. The network monitoring with the new system will start in 2017. To ensure the quality of skid resistance measurements and further cooperation in this field, it has been decided to initiate an alliance between BASt and the Dutch road owner Rijkswaterstaat (RWS). This alliance will facilitate an exchange of research activities, calibration of the Dutch systems according to the existing German Standard as well as control measurements with a BASt-device on the Dutch network during the network monitoring. During 2016 also comparative measurements will be performed on a network level with the current Dutch device and with an SKM device to determine a conversion between the two and to be able to define new threshold values.
Knowledge of material properties is of great importance when developing new types of concrete and construction methods for road building, and for quality control and quality assurance. Physical material characteristics are likewise the basis for dimensioning and assessing the residual substance of concrete pavements. One relevant characteristic when examining thermally induced stress and deformation is the coefficient of thermal expansion (CTE) of concrete. This indicator, for example, significantly influences the longitudinal expansion of the pavement system as well as the degree of curling of slabs and joint movements. Extensive tests were conducted during the technical engineering assessment of the structural substance of concrete pavements in the German motorway network, including tests to determine the CTE of existing types of concrete. Because no standardised procedure currently exists in Germany for using tests to determine the CTE of concrete, the initial task was to develop a suitable test procedure from a road-building perspective, taking consideration of the national prevailing structural conditions. This article presents the results of selected status analyses, in which the CTE was determined for a total of 656 individual samples. The values calculated for the top and bottom drilled core layer are in the range 8.9 – 13.2 x 10-6/K, whereby the average CTE assumes a value of 10.7 x 10-6/K. The deviations of the CTEs from the bottom and top drilled core layer are in principle significantly below the limitation to a maximum of 2.50 x 10-6/K recommended in literature.
APT with the mobile load simulator MLS10 towards non-destructive pavement structural analysis
(2019)
In 2014 a research program has been started about non-destructive test methods to evaluate the structure of pavements. This task has been given to two research groups - first research group is led by RWTH Aachen University (Rheinisch-Westfälische Technische Hochschule) and the second by University of Siegen. This paper focuses on the initial findings of the running research program. The assessment of the existing infrastructure and its condition will be one of the main tasks during the next years in order to use the available budget for maintenance accurately and efficiently. Therefore, it is necessary to identify possible damages and examine their effects on the road construction. BASt (Federal Highway Research Institute) is using the Mobile Load Simulator MLS10 for accelerated pavement testing (APT) on different types of pavements. In addition to non-destructive test methods, sensors are applied to measure structural impacts. The overall objective of this research program is to develop a non-destructive test method that allows the calculation of the remaining life time and load cycles of pavements. To simulate realistic wheel loads in a short period of time the MLS10 on German full scale standard pavement constructions has been used. The first pavement test section was loaded with 3 x 10 high 6 50 kN wheel loads while the second, thinner pavement test section was loaded with 3 x 10 high 5 50 kN wheel loads. Both loads are equivalent to the pavement design load. Three different strategies have been used to analyze and monitor structural changes. The innovative measurements have been realized by the two research groups to collect data for their models. The RWTH Aachen collected data with twelve geophones aligned in a row parallel to the wheel path. The geophones measure the entire vertical deflection basin of the pavement surface that exists due to the passing real truck wheels. These measurements were done for different truck speeds and at different transverse distances to the wheel path. The University of Siegen collected data by using acceleration sensors on the surface of the road construction. After recording the data they were integrated into displacement signals and evaluated. Additionally to those measurements BASt used conventional equipment to monitor the pavement structure and surface characteristics. The measurements and evaluation tools used for the innovation program have a high potential to validate APT programs in the future. Based on this research it is possible to start further research activities to push the non-destructive evaluation of pavements structures - not only in APT - into an improved direction.
Measuring and characterizing airborne particulate matter (PM) is an important research area because PM can lead to impacts on health and to visibility reduction, material damage and groundwater pollution. In regard to road dust, suspension and re-suspension and the contribution of non-exhaust PM to total traffic emissions are expected to increase as a result of predicted climate scenarios. European environmental regulations have been enforced to reduce exhaust particle emissions from road traffic, but little attention has been paid to reducing non-exhaust coarse particle emissions due to traffic. Therefore, a monitoring program for coarse PM has been initiated in early 2013 to assess the predicted increase in the abundance of non-exhaust particles. Particle sampling was performed with the passive-sampler technique Sigma-2. The subsequent single-particle analysis allows for characterization of individual particles, determination of PM size distribution, and calculation of PM mass concentrations. Two motorways n ear Cologne (Koeln), Germany were selected as sampling sites, and the experimental setup in the field was realized with a so-called twin-site method. The present study reports single-particle analysis data for samples collected between May 31, 2013 and May 30, 2014. Coarse PM, generated through multi-source mechanisms, consists of, e.g., tire-wear, soot aggregates, and mineral dust. The highest mass concentration occurs at both motorways in spring, and the observed PM mainly contains traffic-abrasion particles. The field measurements show that the minimum PM concentration was found in the 5 to 12-°C temperature range, whereas the maximum concentration was observed in both the "5 to 5-°C and the 12 to 24-°C ranges, in agreement with previous laboratory measurements. Correlation between super-coarse (d p 10"80 μm, geometric equivalent diameter) PM concentration and precipitation displays a significant increase in concentration with decreasing number of precipitation events (dry weather periods).
For the determination of the road surface roughness common methods have been established, like Skid Resistance Tester (SRT) or the Sideway-force Coefficient Routine Investigation Machine (SCRIM). Both methods are used to measure a comparable and reliable maximum friction potential value and to assess the quality of the road surface. However, the comparison of the measurements under real conditions and the results of measurements with SRT and SCRIM showed only minor correlations. The paper shows the comparison between these standardised methods and real vehicle braking tests and discusses the results.
This study aimed to better understand nitrate transport in the soil system in a part of the state of North Rhine-Westphalia, in Germany, and to aid in the development of groundwater protection plans. An advection-diffusion (AD) cell was used in a miscible displacement experiment setup to characterize nitrate transport in 12 different soil samples from the study area. The three nitrate sorption isotherms were tested to define the exact nitrate interaction with the soil matrix. Soils varied in their properties which in its turn explain the variations in nitrate transport rates. Soil texture and organic matter content showed to have the most important effect on nitrate recovery and retardation. The miscible displacement experiment indicated a decrease in retardation by increasing sand fraction, and an increase in retardation by increasing soil organic matter content. Soil samples with high sand fractions (up to 94 %) exhibited low nitrate sorption capacity of less than 10 %, while soils with high organic matter content showed higher sorption of about 30 %. Based on parameterization for nitrate transport equation, the pore water velocity for both sandy and loamy soils were significantly different (P < 0.001). Pore water velocity in sandy soil (about 4 x 10 high 3 m/s) was about 100 to 1000 larger than in loamy soils (8.7 x 10 high 5 m/s). On the other hand, the reduction in nitrate transport in soils associated with high organic matter was due to fine pore pathways clogged by fine organic colloids. It is expected that the existing micro-phobicity increased the nitrate recovery from 9 to 32 % resulting in maximum diffusion rates of about 3.5 x 10 high 5 m/s2 in sandy soils (sample number CS-04) and about 1.4 x 10 high 7 m/s2 in silt loam soils (sample number FS-02).
Road markings are an essential component of a safe road. In particular, the optical guidance at night and under wet conditions rates high. Special surface textures of road markings can enhance the nighttime visibility during wetness, but they can lead on the other hand to noise emission during passages of vehicles and thus annoy residents. In the present study the tyre/road marking noise is analysed based on two different measurement methods for traffic noise: Several different road markings with increased nighttime visibility during wetness were overrun and the noise was determined by controlled coast-by measurements as well as close-proximity measurements. For both measuring methods the averaged A-weighted sound pressure levels were determined and an analysis of the third octave spectra was performed in order to identify annoying tonal components. The results of both measurement methods were compared with each other. Limitations of the individual measurement methods were overcome by combining the data. Properties of road marking noise depending on the texture of the marking are discussed in relation to those of road surface noise. The results will help specifying road marking texture types that ensure less annoyance and at the same time good visibility at wetness and night-time.
In Europe, in situ measurements of sound reflection and airborne sound insulation of noise barriers are usually done according to CEN/TS 1793-5. This method has been improved substantially during the EU funded QUIESST collaborative project. Within the same framework, an inter-laboratory test has been carried out to assess the repeatability and reproducibility of the newly developed method when applied to real-life samples, including the effect of outdoor weather variability and sample ageing. This article presents the statistical analysis of the inter-laboratory test results, and the values of the repeatability and the reproducibility, both in one-third octave bands and for the single-number ratings. The estimated reproducibility values can be used as the extended measure of uncertainty at the 95% credibility level in compliance with the ISO GUM. The repeatability and reproducibility values associated with airborne sound insulation are also compared with the corresponding values for laboratory measurements in building acoustics and an acceptable agreement is found.
Structured road markings are becoming popular as edge line on high speed roads, ensuring night time visibility (retroreflection) during rain. These markings are often also "audio-tactile": vehicles (un)intentionally driving over it may produce much more tyre/road sound, which may be observed in the vehicle but also in the vicinity. The sound increase inside the car can be considered as a positive side effect, as it alarms the driver and may be very helpful for the prevention of "doze off" traffic accidents. The sound increase perceived outside the car however, may have a positive aspect as it can warn people on the emergency lane about the approaching vehicle, but it may as well annoy people living around. A method for the assessment of the acoustic properties of audio-tactile markings has been developed. It is mainly based on the "Close Proximity" (CPX) method, an ISO method intended for the acoustic assessment of pavements. The results of measurement campaigns with CPX trailers in Belgium and Germany according to a specially designed procedure are presented. The feasibility of the method is discussed. The research has been carried out in the frame of the standardization activities of the CEN working group CEN/TC226/WG2 "Horizontal signalization".
The grip between the road surface and vehicle tires is the physical basis for the moving of all vehicles in road traffic. In case of an accident the available grip level is one of the most relevant influence factors, influencing the causation and the procedure of the accident. However, the estimation of the grip level is not easy and therefore, is commonly not done on the accident scene. This is especially true for the measurement of the water depth. Until now, real accident databases provide no measurement data about the grip level and the water film depth and thus, the estimation of its influence is not possible yet. From the tyre manufacturers point of view, it is important to know about the road conditions (namely grip level, macro-texture, water depth, temperature) at the accident scene, as well as the operating conditions of the vehicles (braking, loss of control, speed, etc). These data is necessary to define relevant tyre traction tests for the end-user and for regulations. For this reason VUFO and Michelin developed a consistent method for the measurements of grip level and water depth for the accidents of the GIDAS database. The accident research team of Dresden, which documents about 1000 accidents with at least one injured person every year, is measuring the micro-roughness and the macro-roughness directly on the spot. For the measurement of the micro-roughness a Skid Resistance Tester (British Pendulum) is used. The Mean Texture Depth (describing the macro-roughness) is measured by the Sand Depth Method. Since June 2009, measurements for more than 700 accidents including 1200 participants have been carried out. In case of wet or damp road conditions during the accident, the water depth is measured additionally. Therefore VUFO and Michelin developed a special measurement device, which allows measurements with an accuracy of 1/10 millimetre. The measurement point at the accident scene is clearly defined and thus, the results are comparable for all different accidents and participants. The use of the GIDAS database and the accident sampling plan allows representative statements for the German accident scenario. With this data it is possible for the first time to have an accurate view of the road conditions at the accident scene. One possibility is a more detailed estimation of hydroplaning accidents using the actually measured water depths. The development of new testing methods and new tires can be based on the real situation of the road infrastructure. Furthermore, the combination of the technical GIDAS data and the measured road surface properties can also be used for the estimation of effectiveness of several safety systems like the brake assist and/or emergency braking systems. The calculation of a reduced collision speed due to the use of a brake assist is only one example for the application of real measured grip level data.