Refine
Year of publication
Document Type
- Conference Proceeding (14) (remove)
Language
- English (14) (remove)
Keywords
- Measurement (14) (remove)
Institute
The German highway network hast o face new challenges in the near future, e.g. increasing traffic density and loads, climate change effects and new quality requirements regarding sustainability. It is necessary to come up with foresighted concepts in the present to be prepared for these challenges. Therefore it is important to adapt and enhance innovative attempts, which take changing impacts into account. One goal of these efforts is the development of adaptive systems for the provision of information and a holistic evaluation in real time. The paper describes the recent research and developments on a system for information and holistic evaluation in real time, taking into account sensor networks, evaluation procedures and their implementation in existing maintenance and inspection strategies.
Structured road markings are becoming popular as edge line on high speed roads, ensuring night time visibility (retroreflection) during rain. These markings are often also "audio-tactile": vehicles (un)intentionally driving over it may produce much more tyre/road sound, which may be observed in the vehicle but also in the vicinity. The sound increase inside the car can be considered as a positive side effect, as it alarms the driver and may be very helpful for the prevention of "doze off" traffic accidents. The sound increase perceived outside the car however, may have a positive aspect as it can warn people on the emergency lane about the approaching vehicle, but it may as well annoy people living around. A method for the assessment of the acoustic properties of audio-tactile markings has been developed. It is mainly based on the "Close Proximity" (CPX) method, an ISO method intended for the acoustic assessment of pavements. The results of measurement campaigns with CPX trailers in Belgium and Germany according to a specially designed procedure are presented. The feasibility of the method is discussed. The research has been carried out in the frame of the standardization activities of the CEN working group CEN/TC226/WG2 "Horizontal signalization".
During a lifecycle a tyre undergoes degradations due to mechanical wear and chemical ageing which affect not only durability and safety but also tyre/road noise emission and rolling resistance. This paper presents a study with the purpose to study how much tyre/road noise and rolling resistance change when car tyres are worn down from the original 8 mm tread depth to 2 mm, and when chemical ageing of the tyre rubber is simulated by exposure to heat. Six car tyres of different types were selected for the study which were worn on a wear machine in steps of 2 mm tread depth. Before, between and after these wear sessions tyre/road noise and rolling resistance were measured on two drum facilities with different surface textures, including replicas of ISO surfaces. Additionally, coast-by and CPX measurements were made on outdoor ISO test tracks. The results show that the wear and age effect was low on ISO surfaces but dramatic (noise increased with wear) on the rough-textured surface and high but opposite on an extremely smooth surface.
Knowledge of material properties is of great importance when developing new types of concrete and construction methods for road building, and for quality control and quality assurance. Physical material characteristics are likewise the basis for dimensioning and assessing the residual substance of concrete pavements. One relevant characteristic when examining thermally induced stress and deformation is the coefficient of thermal expansion (CTE) of concrete. This indicator, for example, significantly influences the longitudinal expansion of the pavement system as well as the degree of curling of slabs and joint movements. Extensive tests were conducted during the technical engineering assessment of the structural substance of concrete pavements in the German motorway network, including tests to determine the CTE of existing types of concrete. Because no standardised procedure currently exists in Germany for using tests to determine the CTE of concrete, the initial task was to develop a suitable test procedure from a road-building perspective, taking consideration of the national prevailing structural conditions. This article presents the results of selected status analyses, in which the CTE was determined for a total of 656 individual samples. The values calculated for the top and bottom drilled core layer are in the range 8.9 – 13.2 x 10-6/K, whereby the average CTE assumes a value of 10.7 x 10-6/K. The deviations of the CTEs from the bottom and top drilled core layer are in principle significantly below the limitation to a maximum of 2.50 x 10-6/K recommended in literature.
The Netherlands is on the way to change its existing skid resistance measuring method for its highway network from the Dutch RAW 72, a longitudinal force method, to the Sideway Force method. This method is described in the Technical Specification 15901-8 (SKM device) as well as 15901-6 (SCRIM device) and is in use in 9 European countries. The CEN TC 227 WG5 on Surface Characteristics is currently working on combining of these two technical Specifications into a European standard for Sideway-Force (SWF) measurement devices. The idea of this change in the Netherlands was perceived in 2013 and since then a lot of meetings have been held with the different Dutch decision makers as well as with countries which currently operate SWF devices. There was an intensive exchange of knowledge about these devices and their corresponding quality assurance systems, because the Netherlands wanted to incorporate and rely on an existing system of a neighbor country without losing their present level of quality. The Netherlands has therefore decided to incorporate the German SKM approach. The network monitoring with the new system will start in 2017. To ensure the quality of skid resistance measurements and further cooperation in this field, it has been decided to initiate an alliance between BASt and the Dutch road owner Rijkswaterstaat (RWS). This alliance will facilitate an exchange of research activities, calibration of the Dutch systems according to the existing German Standard as well as control measurements with a BASt-device on the Dutch network during the network monitoring. During 2016 also comparative measurements will be performed on a network level with the current Dutch device and with an SKM device to determine a conversion between the two and to be able to define new threshold values.
Federal highway A 26 in Germany : reinforced dams in soft soils - control method according DIN 1054
(2004)
In 2001 the construction of the Federal Highway A 26 in Lower Saxony (north of Germany) was started. In this area the underground is without any substantial bearing capacity as it consists of soft layers ( clay, peat) with a thickness of up to 12 m. Because it was not possible to exchange the soil neither completely nor partially pre-loading procedure (consolidation method) was chosen for this construction. Short- and long-term stability are ensured by the use of high-tensile fabrics for reinforcement at the dam basis. The vertical and horizontal deformations and the stress changes in the soil, caused by the pre-load procedure, has to be controlled by special geotechnical measurements. Additionally, in the higher parts of the dam the strain behaviour of the high-tensile fabrics is measured. These measurements form the basis for the application of the control method according DIN 1054. In this article, the special circumstances of this project are described. Further on the geotechnical measurements, the winning and evaluation of the necessary parameters of the subsoil, and the consequences of these data for the ongoing of the project are laid down. Intermediate results of the geotechnical measurements are described.
Road markings are an essential component of a safe road. In particular, the optical guidance at night and under wet conditions rates high. Special surface textures of road markings can enhance the nighttime visibility during wetness, but they can lead on the other hand to noise emission during passages of vehicles and thus annoy residents. In the present study the tyre/road marking noise is analysed based on two different measurement methods for traffic noise: Several different road markings with increased nighttime visibility during wetness were overrun and the noise was determined by controlled coast-by measurements as well as close-proximity measurements. For both measuring methods the averaged A-weighted sound pressure levels were determined and an analysis of the third octave spectra was performed in order to identify annoying tonal components. The results of both measurement methods were compared with each other. Limitations of the individual measurement methods were overcome by combining the data. Properties of road marking noise depending on the texture of the marking are discussed in relation to those of road surface noise. The results will help specifying road marking texture types that ensure less annoyance and at the same time good visibility at wetness and night-time.
For the determination of the road surface roughness common methods have been established, like Skid Resistance Tester (SRT) or the Sideway-force Coefficient Routine Investigation Machine (SCRIM). Both methods are used to measure a comparable and reliable maximum friction potential value and to assess the quality of the road surface. However, the comparison of the measurements under real conditions and the results of measurements with SRT and SCRIM showed only minor correlations. The paper shows the comparison between these standardised methods and real vehicle braking tests and discusses the results.
The purpose of this paper is to review injuries found in real world lateral collisions and determine the mechanisms responsible for certain kinds of biomechanical failure. During the last years the distribution of deaths among the different types of accidents has changed. Lateral collisions now are the most frequent cause of fatal and other serious injuries. Every third accident is an impact from the side, while every second fatality is the result of a lateral accident. Just a few years ago this value was no higher than 30%. This is probably the result of increasing safety standards for frontal collisions (airbags, seatbelt usage, structural improvements of cars, etc.). Although the number of registered vehicles increased, the total amount of fatalities decreased during the same period. Thus it is now necessary to pay greater attention to the lateral accident situation in order to improve road safety and decrease the number of traffic injuries. Several European organisations had decided to launch the project SID2000, which was funded by the European Commission, with the intention of gathering more knowledge on injuries occurring in lateral accidents and the mechanisms that lead to such injuries. This should enable the group to define the requirements for a new side impact dummy (SID) to be designed. Within the same project the existing TNO-EUROSID 1 was enhanced by another group and the experience gained has now enabled allowed to design a better measuring device for side impacts. The data used for this contribution came from sources from all over Europe and had to be gathered in such a manner that as many accident parameters as possible were taken into account.
New vehicle types are extensively tested to check almost all factors that influence ride and handling. With reference to the Association of German Car Tuners" (VDAT e.V.) valuations, approximately 10% of all cars in Germany are being modified by their owners. 28 % of those modifications" sales are divergent wheel-tire combinations, 13 % are tuning measures on the chassis suspension or wheel spacers. In almost all cases the singular modifications present a general permission for specific vehicles they have been tested in. Combined tuning measures, however, are often checked by just one inspector, following a procedure of mostly subjective assessment criteria. Today, critical attributes are only being observed, in case a vehicle is involved in an accident and the modifications are identified as crash causal factors or as a cofactor on the development of a crash. For the first time, a field study allows a survey of safety affecting chassis modifications. The test layout has to comply with some basic conditions. Different vehicle concepts with a wide margin of modifications are required to get a high transferability of the results. A total amount of more than 150 tested vehicles serves the same purpose. The tests are limited concerning the installation time of measurement techniques and the requirement that no damage, defilement or immoderate wear of the vehicles are accepted by their owners. Due to such factors as well as the driver Ìs acceptance, the vehicles are controlled by its owners instead of robots or test drivers. For keeping down the driver- influence, the lane has narrow boundaries and the driver has to drive in strictly adherence to the given instructions. After gathering all modifications, as well as static and kinematic parameters like the toe and camber angle, dynamic testing of predominantly lateral dynamics is conducted. Besides standardized tests like the ISO 3888-2 (Obstacle Avoidance) or the ISO 14512 (Braking on Surfaces with Split Coefficient of Friction), to test the influence of modified kingpin offsets caused by wheel spacers, some deviant tests are conducted. Those are required due to the demand of objective test results for road tests with vertical induced stimulation of the chassis suspension. Hence, new tests on corner braking with and without vertical stimulation have been developed. The interpretation of data includes thresholds, e.g. the maximum entrance velocity without hitting cones, on the one hand, and the analysis of characteristics of data concerning time and frequency range, "1-second values" and peak response times on the other hand. Besides the thresholds as indicators for the achievable velocities, which are mainly affected by friction coefficients, the vehicle reaction in the course of time characterizes the vehicle reaction in the threshold range and consequently the operational demands on the driver. The field study has started and promises the first long-range analysis of chassis modifications. The results offer a basis for hypothesis and resultant further test layouts for oncoming studies of the identified critical tuning measures.