Filtern
Erscheinungsjahr
Dokumenttyp
Schlagworte
- Kopf (28) (entfernen)
Institut
- Sonstige (19)
- Abteilung Fahrzeugtechnik (16)
When the EEVC proposed the full-scale side impact test procedure, it recommended that consideration should be given to an interior headform test in addition. This was to evaluate areas of contact not assessed by the dummy. EEVC Working Group 13 has been researching the parameters of a possible European headform test procedure in four phases. Earlier stages of the research have been presented at previous ESV conferences. The conclusions from these have suggested that the US free motion headform should be used in any European test procedure and that it should be a free flight test, not guided. This research has now culminated in proposals for a European test procedure. This paper presents the proposed EEVC side impact interior headform test procedure, giving the rationale for the test and the first results from the validation phase of the test protocol.
Cycle helmets have continued to increase in popularity since their introduction half a century ago. Many studies indicate that overall, head injury can be significantly reduced by wearing them. This study was conducted using two distinct sets of real-world cycling collision data from Ireland, namely cases involving police collision reports and cases involving admission to a hospital emergency department. The analyses sought to simulate and analyse the protective performance of cycle helmets in such collision scenarios, by comparing the Head Injury Criterion score and peak head accelerations, both linear and angular. Cycle collisions were simulated using the specialised commercial software MADYMO. From the simulation results, these key metrics were compared between the same-scenario helmeted and unhelmeted cyclist models. Results showed that the inclusion of bicycle helmets reduced linear accelerations very significantly, but also increased angular accelerations significantly compared to unhelmeted situations. Given the modest protective performance of cycle helmets against angular accelerations, it is recommended that cycle helmet manufacturers and international test standards need to pay more attention to head angular accelerations.
Aim of the study was to evaluate the protective effect of bicycle helmets particularly considering injuries to the head and to the face. Accidents with the participation of bicyclists which occurred from 2000 to 2007 were chosen from GIDAS. We observed that injuries to the head and face were more severe in the group of non-helmeted riders. There seems to be no significant difference in injuries with AIS 3-6. Altogether 26 cyclists were killed. 2 of them wore a helmet (1% of helmeted cyclists), 24 did not (1% of non-helmeted cyclists). Only one killed rider (without helmet) did not suffer from polytrauma (only head injuries recorded). The findings seem to support the thesis of a preventive effect of the bicycle helmet, however the two groups are different in their characteristics related to riding speed. Necessarily we need a multivariate model to evaluate the effect of helmets.
At the 2005 ESV conference, the International Harmonisation of Research Activities (IHRA) side impact working group proposed a 4 part draft test procedure, to form the basis of harmonisation of regulation world-wide and to help advances in car occupant protection. This paper presents the work performed by a European Commission 6th framework project, called APROSYS, an further development and evaluation of the proposed procedure from a European perspective. The 4 parts of the proposed procedure are: - A Mobile Deformable Barrier test; - An oblique Pole side impact test; - Interior headform tests; - Side Out of Position (OOP) tests. Full scale test and modelling work to develop the Advanced European Mobile Deformable Barrier (AE-MDB) further is described, resulting in a recommendation to revise the barrier face to include a bumper beam element. An evaluation of oblique and perpendicular pole tests was made from tests and numerical simulations using ES-2 and WorldSID 50th percentile dummies. It was concluded that an oblique pole test is feasible but that a perpendicular test would be preferable for Europe. The interior headform test protocol was evaluated to assess its repeatability and reproducibility and to solve issues such as the head impact angle and limitation zones. Recommendations for updates to the test protocol are made. Out-of-position (OOP) tests applicable for the European situation were performed, which included additional tests with Child Restraint Systems (CRS) which use is mandatory in Europe. It was concluded that the proposed IHRA OOP tests do cover the worst case situations, but the current test protocol is not ready for regulatory use.
Recent accident statistics from the German national database state bicyclists being the second endangered group of vulnerable road users besides pedestrians. With 399 fatalities, more than 14.000 seriously injured and more than 61.000 slightly injured persons on german roads in the year 2011, the group of bicyclists is ranked second of all road user groups (Statistisches Bundesamt, 2012). While the overall bicycle helmet usage frequency in Germany is very low, evidence is given that its usage leads to a significant reduction of severe head injuries. After an estimation of the benefit of bicycle helmet usage as well as an appropriate test procedure for bicyclists, this paper describes two different approaches for the improvement of bicyclist safety. While the first one is focusing on the assessment of the vehicle based protection potential for bicyclists, the second one is concentrating on the safety assessment of bicycle helmets. Within the first part of the study the possible revision of the existing pedestrian testing protocols is being examined, using in depth accident data, full scale simulation and hardware testing. Within the second part of the study, the results of tests according to supplemental test procedures for the safety assessment of bicycle helmets developed by the German Federal Highway Research Institute (BASt) are presented. An additional full scale test performed at reduced impact speed proves that measures of active vehicle safety as e.g. braking before the collision event do not necessarily always lead to a reduction of injury severity.
Die Untersuchung sollte erörtern, ob es empfehlenswert ist, das Testverfahren zum streifenden Anprall eines Motorradhelmes auf die Straßenoberfläche in die ECE-R 22 aufzunehmen. Dazu war zu klären, ob die Testmethode geeignet ist, rotatorische Kräfte auf den Prüfkopf zu erfassen und ob sich aufgrund der Unfallsituationen eine Notwendigkeit für ein solches Testverfahren ergibt. Die Messergebnisse zeigen, dass der Zusammenhang zwischen der verletzungswirksamen Rotationsbeschleunigung und der im Testverfahren gemessenen Tangentialkraft nicht ohne Zweifel belegbar ist. Somit wäre zu fordern, dass statt der Tangentialkraft die Rotationsbeschleunigung als Verletzungskriterium betrachtet wird. Dafür wird jedoch ein sehr hoher Anspruch an die Messtechnik im Labor gestellt. Aus der Sicht der Unfallforschung lässt sich sagen, dass bei derartigen Anprallsituationen, insbesondere bei Anprallgeschwindigkeiten von unter 40 km/h, die sich im Laborversuch realisieren lassen, nur mäßige Kopfverletzungen auftreten (AIS 2 oder geringer). Der hohe Aufwand des Testverfahrens scheint also nicht gerechtfertigt zu sein.
Der Nutzen des Schutzhelmes für motorisierte Zweiradfahrer ist unumstritten. Die Grenzwerte für eine zulässige Kopfbeschleunigung bei der Prüfung des Dämpfungsverhaltens gemäß ECE-R 22 sind jedoch weiterhin in der Diskussion. In der vorliegenden Untersuchung wird deshalb die Kopfbelastung eines Dummys beim Pkw-Crash-Versuch mit den Belastungen des behelmten Prüfkopfes bei Fallversuchen gemäß ECE-R 22 verglichen. Bei den durchgeführten Fallversuchen besteht ein enger Zusammenhang zwischen HIC und maximaler Beschleunigung, der durch eine analytische Funktion beschrieben werden kann. Es kann gezeigt werden, dass die bei ECE-R 22 zulässige Kopfbeschleunigung von 300 g einem HIC von etwa 3400 entspricht. Zur Bewertung von Schutzhelmen mit verbesserten Stoßabsorptionseigenschaften erscheint es sinnvoll, wie anhand von Modellrechnungen gezeigt wird, den HIC als Schutzkriterium einzuführen. Bei einer Anprallgeschwindigkeit von 7 m/s kann ein HIC von 1500 als realistische Forderung angesehen werden, sofern bei der ECE-Regelung der sogenannte Zweitschlag entfällt. Bei den Pkw-Versuchen ist kein Zusammenhang zwischen HIC und maximaler Beschleunigung vorhanden. Hier ist der HIC als Verletzungskriterium etabliert, und das ist für den komplexen Verlauf des Signals der Kopfbeschleunigung sinnvoll. Eine Bewertung nach anderen Kopfschutzkriterien würde die Rangfolge der einzelnen Versuche ändern. Bei Helmversuchen auf den Stirnanprallpunkt B werden starke Rotationen des rückprallenden Systems Prüfkopf/Helm beobachtet. In Verbindung damit treten hohe Rotationsbeschleunigungen auf. Diese liegen, wie bei einem Teil der Helmversuche gemessen, zwischen 2,4 und 4,8 krad/s2.
Beschrieben wird die Evaluierung eines Testverfahrens der Arbeitsgruppe 10 des European Experimental Vehicle Committee, mit dem die "Fußgängerverträglichkeit" von Frontflächen von Personenkraftwagen bestimmt werden kann. Dabei werden verschiedene Anprallarten von Fußgängern an Fahrzeugen simuliert: der Anprall eines Beines an den Stoßfänger, der Anprall des Oberschenkels an die Vorderkante der Fronthaube und der Anprall des Kopfes auf die Fronthaube. Im Beitrag wird auf die Durchführung von Tests zum Oberschenkelanprall und zum Beinanprall an drei verschiedenen Fahrzeugtypen eingegangen. Beschrieben werden Testverfahren, Versuchsaufbau und Versuchsdurchführung. Die Versuchsreihe zeigte, dass das entwickelte Testverfahren praktikabel ist.