Abteilung Fahrzeugtechnik
Refine
Year of publication
Document Type
- Conference Proceeding (28)
- Working Paper (7)
- Article (6)
- Book (4)
Keywords
- Anfahrversuch (45) (remove)
Institute
- Abteilung Fahrzeugtechnik (45)
- Sonstige (21)
- Präsident (1)
Streuung von Schutzkriterien in kontrollierten Aufprallversuchen gegen die starre 30 Grad-Barriere
(1983)
Gegenstand der Arbeit ist die Ermittlung von Streubreiten von Fahrzeug- und Dummy-Messwerten in Aufprallversuchen bei Geschwindigkeiten von 50 km/h gegen eine starre 30-°-Barriere. Zu den fahrzeugseitigen Messwerten gehörten die Deformation der Frontstruktur, die maximale Fahrzeugverzögerung, die mittlere Fahrzeugverzögerung und Anforderungen der ECE-Regelung 33. Die gemessenen Standardabweichungen der Einzelwerte lagen mit zwei bis sieben Prozent deutlich unter zehn Prozent. Höhere Standardabweichungen der Messwerte wurden dann beobachtet, wenn Aufpralle nach den Mustern Kopf-Lenkrad (Fahrer), Brust-Lenkrad (Fahrer) und Knie-Armaturentafel (Fahrer und Beifahrer) nicht in allen Versuchen zu beobachten sind. Hohe Streubreiten für die Kopfbeschleunigung bzw. die Beschleunigung der Brust des Dummy auf dem Fahrersitz wurden dadurch verursacht, dass in einem Versuch eine unübliche Vorverlagerung des Dummys infolge mangelhafter Gurtwirkung mit nachfolgendem Brust-Lenkrad-Kontakt zu beobachten war.
Von der Bundesanstalt für Straßenwesen (BASt) und dem Rheinisch-Westfälischen TÜV wurde 1988/89 eine Pilotstudie zum Einfluss der Korrosion auf die passive Sicherheit von Pkw bei drei unterschiedlichen Fahrzeugtypen durchgeführt. Es wurde je ein dem Alter entsprechend durchschnittlich durch Korrosion geschädigtes älteres und ein möglichst gering geschädigtes jüngeres Fahrzeug bezüglich des Korrosionszustandes vermessen und im Aufprallversuch getestet. Bei den von der BASt durchgeführten Wandaufpralltests versagten insbesondere bei den älteren Fahrzeugen sicherheitsrelevante Fahrzeugteile. Es wurde daraufhin beschlossen, die Pilotstudie mit der vorliegenden zweiten Untersuchung unter den folgenden zwei Vorgaben fortzuführen: - Verbreiterung der Datenbasis von Tests mit weiteren Fahrzeugtypen mit starker Korrosion. - Prüfung von Fahrzeugen des gleichen Typs wie in der Pilotstudie, jedoch sollten an ihnen Korrosionsschutzmaßnahmen verwirklicht sein, welche die Automobilindustrie mit Beginn der 80er Jahre in die Fertigung eingeführt hatte. Die stark korrodierten Fahrzeuge der jetzt vorliegenden Untersuchung zeigten ein ähnliches Versagensspektrum wie die stark korrodierten Fahrzeuge der Pilotstudie. An den korrosionsgeschützten und auch jüngeren Nachfolgemodellen der Fahrzeuge der Pilotstudie konnte kein korrosionsbedingter Einfluss auf die passive Fahzeugsicherheit mehr gefunden werden.
Wegen der wachsenden Verbreitung von Fahrradanhängern zum Kindertransport und der möglichen Unfallgefährdung ist im vorliegenden Forschungsprojekt deren passive Sicherheit untersucht worden. Zudem wurde der Frage nachgegangen, ob der Transport von Kindern im Fahrradanhänger sicherer ist als mit dem Fahrrad mit Kindersitzen. In Absprache mit Herstellern und Vertreibern wurden verschiedene Untersuchungen durchgeführt. Es handelte sich um Anprallversuche (Anfahrversuche), Rollwagenversuche (Schlittenversuche) sowie Kopffreiheitsprüfungen und Fallversuche. Bei den Versuchen waren die Prüfobjekte mit einem oder zwei Dummies besetzt, die mit Messdatenaufnehmern ausgestattet waren. Verschiedene Messdaten, zum Beispiel Kopf- und Brustbeschleunigung, wurden erfasst und ausgewertet. Zusätzlich wurde das Kopfschutzkriterium (HPC) berechnet und bewertet. Entstandene Schäden an den Prüfobjekten wurden aufgenommen und durch Fotos dokumentiert. Die Versuchsabläufe selbst wurden mit Hochgeschwindigkeitskameras aus verschiedenen Positionen aufgezeichnet. Beim Anfahrversuch mit einem Pkw gegen ein Gespann aus Fahrrad und Anhänger waren direkte Anstöße der Anhängerinsassen an die Pkw-Front zu erkennen. Die Beschleunigungswerte waren dabei relativ hoch. Anstöße gegen Anhängerinnenteile waren bei fast allen Versuchen zu beobachten. Teilweise wurden Radaufhängungen und Radnaben beschädigt. Durch die Rollwagenversuche wurden konstruktive Schwächen bei den Sitzen und Rückhaltesystemen festgestellt. Nähte, Befestigungen und Verstellösen wurden zerstört. Es stellte sich heraus, dass die Qualität des Gurtsystems, die Steifigkeit des Anhängeraufbaus, die Sitzposition der Kinder und die vorhandene Kopffreiheit ausschlaggebend für das Verletzungsrisiko der Insassen sind. Bei den Versuchen mit Fahrradsitzen ergaben sich hohe Beschleunigungswerte durch den direkten Kontakt des Radfahrers mit der Fahrzeugfront und/oder der Fahrbahn. Das Gewicht des Radfahrers, des Fahrrades und auch Fahrradteile bergen ein erhöhtes Verletzungsrisiko für das Kind. Zusätzlich besteht die Gefahr überfahren zu werden, wenn das Kind nach dem Sturz des Fahrrades ungeschützt auf der Fahrbahn liegt. Ein direkter Vergleich der beiden Transportmöglichkeiten war aufgrund der geringen Daten der Versuche mit Fahrradkindersitzen nur bedingt möglich. Tendenziell ist der Transport der Kinder im Fahrradanhänger als weniger gefährlich zu bewerten. Es werden die Vor- und Nachteile dargestellt. Zur Bewertung der Sicherheit von Fahrradanhängern wurden die folgenden Prüfmethoden erarbeitet: - Pendelschlagprüfung für die gesamte Chassisstruktur; - Kopffreiheitsprüfung; - Belastungsprüfung der Aufbaustruktur; - Festigkeitsprüfung der Gurtsysteme. Die Prüfungen sind so aufgebaut, dass sie mit einfachen Mitteln durchzuführen sind. Es sollte somit jedem Anhängerhersteller möglich sein, die passive Sicherheit seiner Produkte umfassend zu untersuchen. Die Prüfverfahren für die Sicherheitsbewertung sollen in eine DIN-Norm und in das Merkblatt für Fahrradanhänger einfließen. Der Original-Forschungsbericht enthält einen umfangreichen Fotoband zu den Einzelheiten der Versuche und Versuchsaufbauten sowie zu den Beschädigungen der Prüfobjekte und kann bei der BASt eingesehen werden.
Many big cities in Europe and elsewhere in the world have problems managing the traffic especially during rush hours. The improvement of the parking problematic and environmental protection as well are important aspects for the future traffic design of urban areas. To improve the traffic situation the development of new traffic concepts and alternative vehicles are required. The BMW company has developed a new type of two-wheel vehicle. This two-wheeler constitutes a totally new concept. BMW implemented a lot of safety features, such as a structure made up of rollover bars and a crush element instead of a front protecting plate. Furthermore the driver can secure himself with two safety belts. The paper contains a description of the novel two-wheel vehicle concept designed so far. BMW's concept and the safety features are also explained. The Federal Highway Research Institute (BASt) was given the task of assessing the concept as a whole with regard to the active and passive safety and the exemption of the obligation to wear a helmet. The expertise concluded that the BMW two-wheeler concept has a very high safety standard. Some extracts of the expertise, in particular the investigations concerning the exemption of the obligation to wear a helmet are presented. Common legal requirements for the vehicle registration of vehicle concepts similar to the BMW two-wheeler in Germany have been formulated.
Side-impact safety of passenger cars is assessed in Europe in a full-scale test using a moving barrier. The front of this barrier is deformable and represents the stiffness of an 'average' car. The EU Directive 96/27/EC on side impact protection has adopted the EEVC Side Impact Test Procedure, including the original performance specification for the barrier face when impacting a flat dynamometric rigid wall. The requirements of the deformable barrier face, as laid down in the Directive, are related to geometrical characteristics, deformation characteristics and energy dissipation figures. Due to these limited requirements, many variations are possible in designing a deformable barrier face. As a result, several barrier face designs are in the market. However, research institutes and car manufacturers report significant difference in test results when using these different devices. It appears that the present approval test is not able to distinguish between the different designs that may perform differently when they impact real vehicles. Therefore, EEVC Working Group 13 has developed a number of tests to evaluate the different designs. In these tests the barrier faces are loaded and deformed in a specific and/or more representative way. Barrier faces of different design have been evaluated. In the paper the set-up and the reasoning behind the tests is presented. Results showing specific differences in performance are demonstrated.
This paper provides an overview of the research work of the European Enhanced Vehicle-safety Committee (EEVC) in the field of crash compatibility between passenger cars. Since July 1997 the EC Commission is partly funding the research work of EEVC. The running period of this project will be two years. The progress of five working packages of this research project is presented: Literature review, Accident analysis, Structural survey of cars, Crash testing, and Mathematical modelling. According to the planned time schedule the progress of research work is different for the five working packages.
EEVC Working Group 15 (Compatibility Between Passenger Cars) has carried out research for several years thanks to collaborative project funded by the E.C. and also by exchanging results of projects funded by national programmes. The main collaborative activity of the EEVC WG15 for the last four years was a research project partly funded by the European Commission, where the group made the first attempt to investigate compatibility between passenger cars in a comprehensive research program. Accident, crash test, and mathematical modelling data were analysed. The main result was that structural incompatibilities were frequently found and identified as the main source of incompatibility problems but were not easy to quantify. Unfortunately as little vehicle information other than mass is recorded in most accident databases, most analyses have only been able to show the effect of mass or mass ratio. Common ideas to improve compatibility have been reached by this group and from discussion with other research groups. They will be investigated in the next phase, where research work will concentrate on the development of methods to assess compatibility of passenger cars. The main idea is that the prerequisite to improve crash compatibility between cars is to improve structural interaction. The most important issue is that improved compatibility must not compromise a vehicle- self protection. Test methods should lead to vehicles which show good structural interaction in car to car accidents. Test methods to prove good compatibility may be an adaptation of existing regulatory test procedures (offset deformable barrier test or full width test like in the USA) for frontal impact or may be new compatibility tests. Additional criteria, e.g. impact force distribution, and maximum vehicle deceleration or maximum vehicle impact force should result in compatible cars. Attempts will be made to estimate the benefit of a more compatible car fleet for the European Community.
The purpose of this paper is to review injuries found in real world lateral collisions and determine the mechanisms responsible for certain kinds of biomechanical failure. During the last years the distribution of deaths among the different types of accidents has changed. Lateral collisions now are the most frequent cause of fatal and other serious injuries. Every third accident is an impact from the side, while every second fatality is the result of a lateral accident. Just a few years ago this value was no higher than 30%. This is probably the result of increasing safety standards for frontal collisions (airbags, seatbelt usage, structural improvements of cars, etc.). Although the number of registered vehicles increased, the total amount of fatalities decreased during the same period. Thus it is now necessary to pay greater attention to the lateral accident situation in order to improve road safety and decrease the number of traffic injuries. Several European organisations had decided to launch the project SID2000, which was funded by the European Commission, with the intention of gathering more knowledge on injuries occurring in lateral accidents and the mechanisms that lead to such injuries. This should enable the group to define the requirements for a new side impact dummy (SID) to be designed. Within the same project the existing TNO-EUROSID 1 was enhanced by another group and the experience gained has now enabled allowed to design a better measuring device for side impacts. The data used for this contribution came from sources from all over Europe and had to be gathered in such a manner that as many accident parameters as possible were taken into account.
EEVC Status report
(2001)
The frontal crash is still an important contributor to deaths and serious injured resulting from road accidents in Europe. As the Hybrid-III dummy used in crash tests is over two decades old, the European Enhanced Vehicle-safety Committee is studying the potential for a new test device. Key is the availability of a well-defined set of requirements that identifies the minimum level of biofidelity required for an advanced frontal dummy. In this paper, a complete set of frontal impact biofidelity requirements, consisting of references , description of test conditions and corridors, is presented.
At the 2001 ESV-Conference the EEVC working group on compatibility (WG 15) reported the first phase of the research work to investigate the major factors influencing compatibility between passenger cars. Following this, WG15 performed an interim study, which was partly subventioned by the European Commission, the results of which are reported in this paper. In the next phase of work, it is intended to complete the development of a suite of test procedures and associated performance criteria to assess the compatibility of passenger cars in frontal impacts The main areas of work for the interim study were: - in depth accident data analysis - the development of methods to assess the potential benefit of improved compatibility - crash testing. The accident analysis identified the major compatibility problems to be poor structural interaction, stiffness mismatching and compartment strength. Different methods to assess the potential benefit of improved compatibility were applied to in depth accident data. Full scale crash testing including a car to car test was performed to help develop the following candidate compatibility test procedures: - a full width wall test with a deformable aluminium honeycomb face and a high resolution load cell wall - an offset barrier test with the EEVC barrier face and a high resolution load cell wall - an offset barrier test with the progressively deformable barrier (PDB) face. The results of the interim study will be presented in detail and the proposed methodology of the next phase to complete the development of a suite of test procedures for the assessment of car to car compatibility in frontal impacts will be outlined
When the EEVC proposed the full-scale side impact test procedure, it recommended that consideration should be given to an interior headform test in addition. This was to evaluate areas of contact not assessed by the dummy. EEVC Working Group 13 has been researching the parameters of a possible European headform test procedure in four phases. Earlier stages of the research have been presented at previous ESV conferences. The conclusions from these have suggested that the US free motion headform should be used in any European test procedure and that it should be a free flight test, not guided. This research has now culminated in proposals for a European test procedure. This paper presents the proposed EEVC side impact interior headform test procedure, giving the rationale for the test and the first results from the validation phase of the test protocol.
Sowohl mit dem 3. Road Safety Action Programme der Europäischen Kommission als auch mit dem deutschen Verkehrssicherheitsprogramm werden die verkehrspolitischen Zielsetzungen zur Erhöhung der Verkehrssicherheit in Europa und Deutschland festgelegt. Hierbei muss die passive Fahrzeugsicherheit auch weiterhin eine bedeutende Rolle übernehmen. Es ist jedoch auch festzustellen, dass durch den zunehmenden Einsatz von Elektronik im Fahrzeug die klassischen Bereiche der aktiven und passiven Fahrzeugsicherheit mehr und mehr ineinander greifen. Der Fortschritt in der Elektronik ermöglicht eine Integration der Systeme der aktiven und passiven Sicherheit. Dadurch lässt sich die Fahrzeugsicherheit weiter steigern. Durch die Vernetzung der Systeme lassen sich sogar Kosten einsparen. Der europäische Regierungsausschuss EEVC (European Enhanced Vehicle-safety Committee), die Verbraucherschutzorganisation Euro NCAP (European New Car Assessment Programme) und die Europäische Kommission mit der eSafety Initiative haben diesen Trend erkannt und entsprechende Aktivitäten eingeleitet.
The objective of European Enhanced Vehicle-safety Committee (EEVC) Working Group (WG) 15 Car Crash Compatibility and Frontal Impact is to develop a test procedure(s) with associated performance criteria and limits for car frontal impact compatibility. This work should lead to improved car to car frontal compatibility and self protection without decreasing the safety in other impact configurations such as impacts with car sides, trucks, and pedestrians. The WG consists of national government representatives who are supported by industrial advisers. The WG serves as a focal point for European research conducted by national and industry sponsored projects. The WG is responsible for collating the results from this research to achieve its objectives. EEVC WG 15 serves as a steering group for the car-to-car activities in the "Improvement of Vehicle Crash Compatibility through the Development of Crash Test Procedures"(VC-COMPAT) project partly funded by the European Commission. This paper presents a review of the current European research status. It also identifies current issues with candidate test procedures and lists the parameters that should be considered in assessing compatibility. The current candidate test procedures are: an offset barrier test with the progressive deformable barrier (PDB) face; a full width wall test with or without a deformable aluminium honeycomb face and a high resolution load cell wall; an offset barrier test with the EEVC barrier and load cell wall. These candidate test procedures must allow assessment of structural interaction, frontal force levels and compartment strength. The WG will report its findings to the EEVC Steering Committee and propose a test procedure in November 2006.
The European Enhanced Vehicle-safety Committee wants to promote the use of more biofidelic child dummies and biomechanical based tolerance limits in regulatory and consumer testing. This study has investigated the feasibility and potential impact of Q-dummies and new injury criteria for child restraint system assessment in frontal impact. European accident statistics have been reviewed for all ECE-R44 CRS groups. For frontal impact, injury measures are recommended for the head, neck, chest and abdomen. Priority of body segment protection depends on the ECE-R44 group. The Q-dummy family is able to reflect these injuries, because of its biofidelity performance and measurement capabilities for these body segments. Currently, the Q0, Q1, Q1.5, Q3 and Q6 are available representing children of 0, 1, 1.5, 3 and 6 years old. These Q-dummies cover almost all dummy weight groups as defined in ECE-R44. Q10, representing a 10 year-old child, is under development. New child dummy injury criteria are under discussion in EEVC WG12. Therefore, the ECE-R44 criteria are assessed by comparing the existing P-dummies and new Q-dummies in ECE-R44 frontal impact sled tests. In total 300 tests covering 30 CRSs of almost all existing child seat categories are performed by 11 European organizations. From this benchmark study, it is concluded that the performance of the Q-dummy family is good with respect to repeatability of the measurement signals and the durability of the dummies. Applying ECE-R44 criteria, the first impression is that results for P- and Q-dummy are similar. For child seat evaluation the potential merits of the Q-dummy family lie in the extra measurement possibilities of these dummies and in the more biofidelic response.
As set out in the Terms of Reference, the objective of European Enhanced Vehicle-safety Committee (EEVC) Working Group (WG) 15 Car Crash Compatibility and Frontal Impact is to develop a test procedure(s) with associated performance criteria for car frontal impact compatibility. This work should lead to improved car to car frontal compatibility and self protection without decreasing the safety in other impact configuration such as impacts with car sides, trucks, and pedestrians. Since 2003, EEVC WG 15 served as a steering group for the car-to-car activities in the "Improvement of Vehicle Crash Compatibility through the development of Crash Test Procedures" (VC-COMPAT) project that was finalised at the end of 2006 and partly funded by the European Commission. This paper presents the research work carried out in the VC-COMPAT project and the results of its assessment by EEVC WG 15. Other additional work presented by the UK and French governments and industry " in particular the European industry - was taken into consideration. It also identifies current issues with candidate testing approaches. The candidate test approaches are: - an offset barrier test with the progressive deformable barrier (PDB) face in combination with a full width rigid barrier test - a full width wall test with a deformable aluminium honeycomb face and a high resolution load cell wall supplemented by the forces measured in the offset deformable barrier (ODB) test with the current EEVC barrier. These candidate test approaches must assess the structural interaction and give information of frontal force levels and compartment strength for passenger vehicles. Further, this paper presents the planned route map of EEVC WG 15 for the evaluation of the proposed test procedures and assessment criteria.
At the 2005 ESV conference, the International Harmonisation of Research Activities (IHRA) side impact working group proposed a 4 part draft test procedure, to form the basis of harmonisation of regulation world-wide and to help advances in car occupant protection. This paper presents the work performed by a European Commission 6th framework project, called APROSYS, an further development and evaluation of the proposed procedure from a European perspective. The 4 parts of the proposed procedure are: - A Mobile Deformable Barrier test; - An oblique Pole side impact test; - Interior headform tests; - Side Out of Position (OOP) tests. Full scale test and modelling work to develop the Advanced European Mobile Deformable Barrier (AE-MDB) further is described, resulting in a recommendation to revise the barrier face to include a bumper beam element. An evaluation of oblique and perpendicular pole tests was made from tests and numerical simulations using ES-2 and WorldSID 50th percentile dummies. It was concluded that an oblique pole test is feasible but that a perpendicular test would be preferable for Europe. The interior headform test protocol was evaluated to assess its repeatability and reproducibility and to solve issues such as the head impact angle and limitation zones. Recommendations for updates to the test protocol are made. Out-of-position (OOP) tests applicable for the European situation were performed, which included additional tests with Child Restraint Systems (CRS) which use is mandatory in Europe. It was concluded that the proposed IHRA OOP tests do cover the worst case situations, but the current test protocol is not ready for regulatory use.
The use of proper child restraint systems (CRS) is mandatory for children travelling in cars in most countries of the world. The analysis of the quantity of restrained children shows that more than 90% of the children in Germany are restrained. Looking at the quality of the protection, a large discrepancy between restrained and well protected children can be seen. Two out of three children in Germany are not properly restrained. In addition, considerable difference exists with respect to the technical performance of CRS. For that reason investigations and optimisations on two different topics are necessary: The technical improvement of CRS and the ease of use of CRS. Consideration of the knowledge gained by the comparison of different CRS in crash tests would lead to some improvements of the CRS. But improvement of child safety is not only a technical issue. People should use CRS in the correct way. Misuse and incorrect handling could lead to less safety than correct usage of a poor CRS. For that reason new technical issues are necessary to improve the child safety AND the ease of use. Only the combination of both parts can significantly increase child safety. For the assessment of the safety level of common CRS, frontal and lateral sled tests simulating different severity levels were conducted comparing pairs of CRS which were felt to be good and CRS which were felt to be poor. The safety of some CRS is currently at a high level. All well known products were not damaged in the performed tests. The performance of non-branded CRS was mostly worse than that of the well known products. Although the branded child restraint systems already show a high safety level it is still possible to further improve their technical performance as demonstrated with a baby shell and a harness type CRS.
A legform impactor with biofidelic characteristics (FlexPLI) which is being developed by the Japanese Automobile Research Institute (JARI) is being considered as a test tool for legislation within a proposed Global Technical Regulation on pedestrian protection (UNECE, 2006) and therefore being evaluated by the Technical Evaluation Group (TEG) of GRSP. In previous built levels it already showed good test results on real cars as well as under idealised test conditions but also revealed further need for improvement. A research study at the Federal Highway Research Institute (BASt) deals with the question on how leg injury risks of modern car fronts can be revealed, reflected and assessed by the FlexPLI and how the impactor can be used and implemented as a legislative instrument for the type approval of cars according to current and future legislations on pedestrian protection. The latest impactor built level (GTα ) is being evaluated by a general review and assessment of the certification procedure, the knee joint biofidelity and the currently proposed injury criteria. Furthermore, the usability, robustness and durability as a test tool for legislation is examined and an assessment of leg injuries is made by a series of tests with the FlexPLI on real cars with modern car front shapes as well as under idealised test conditions. Finally, a comparison is made between the FlexPLI and the current european legislation tool, the legform impactor according to EEVC WG 17.