Sonstige
Filtern
Erscheinungsjahr
Dokumenttyp
- Konferenzveröffentlichung (49)
- Buch (Monographie) (29)
- Wissenschaftlicher Artikel (4)
- Teil eines Buches (Kapitel) (2)
- Bericht (2)
Schlagworte
- Simulation (86) (entfernen)
Institut
- Sonstige (86) (entfernen)
Im Projekt ESIMAS - Echtzeit-Sicherheits-Management-System für Straßentunnel - wurde der Prototyp für ein Expertensystem zur Überwachung von Straßentunneln unter Einbezug innovativer Detektionssysteme entwickelt. Das Ziel von ESIMAS ist die Bereitstellung eines ganzheitlichen modularen Ansatzes zur Überwachung von Straßentunneln, welcher sowohl die präventive Ereignisvermeidung, die schnelle Ereigniserkennung als auch die Ereignisbewältigung verbessern soll. Dieser Ansatz geht deutlich über die aktuellen Möglichkeiten der Tunnelsteuerung und übergeordneten Leitsysteme hinaus. Die zukünftige Unterstützung der Überwachung von Tunnelanlagen mit ESIMAS führt zu einem maßgeblichen Sicherheitsgewinn für den Verkehrsteilnehmer, da durch die umfangreichere und genauere Erfassung und Auswertung von Informationen die Verantwortlichen in den Tunnelleitzentralen besser und schneller reagieren können.
APT with the mobile load simulator MLS10 towards non-destructive pavement structural analysis
(2019)
In 2014 a research program has been started about non-destructive test methods to evaluate the structure of pavements. This task has been given to two research groups - first research group is led by RWTH Aachen University (Rheinisch-Westfälische Technische Hochschule) and the second by University of Siegen. This paper focuses on the initial findings of the running research program. The assessment of the existing infrastructure and its condition will be one of the main tasks during the next years in order to use the available budget for maintenance accurately and efficiently. Therefore, it is necessary to identify possible damages and examine their effects on the road construction. BASt (Federal Highway Research Institute) is using the Mobile Load Simulator MLS10 for accelerated pavement testing (APT) on different types of pavements. In addition to non-destructive test methods, sensors are applied to measure structural impacts. The overall objective of this research program is to develop a non-destructive test method that allows the calculation of the remaining life time and load cycles of pavements. To simulate realistic wheel loads in a short period of time the MLS10 on German full scale standard pavement constructions has been used. The first pavement test section was loaded with 3 x 10 high 6 50 kN wheel loads while the second, thinner pavement test section was loaded with 3 x 10 high 5 50 kN wheel loads. Both loads are equivalent to the pavement design load. Three different strategies have been used to analyze and monitor structural changes. The innovative measurements have been realized by the two research groups to collect data for their models. The RWTH Aachen collected data with twelve geophones aligned in a row parallel to the wheel path. The geophones measure the entire vertical deflection basin of the pavement surface that exists due to the passing real truck wheels. These measurements were done for different truck speeds and at different transverse distances to the wheel path. The University of Siegen collected data by using acceleration sensors on the surface of the road construction. After recording the data they were integrated into displacement signals and evaluated. Additionally to those measurements BASt used conventional equipment to monitor the pavement structure and surface characteristics. The measurements and evaluation tools used for the innovation program have a high potential to validate APT programs in the future. Based on this research it is possible to start further research activities to push the non-destructive evaluation of pavements structures - not only in APT - into an improved direction.
Fire incidents are among the most relevant for people in a tunnel. Therefore, it is important to be sufficiently prepared for such events. A large scale fire test is to be used to help evaluate the initial burning duration and the time it takes for the fire to spread to other vehicles in the tunnel, and in particular how long it takes for a truck carrying wooden pallets to catch fire, taking into consideration the extremely high temperatures. The goal, therefore, is to determine the time it takes for a fire to spread to other vehicles in the tunnel. In the large scale fire test, an accident in a tunnel with one-way traffic is simulated between a truck loaded with approximately 3.7 t of wooden Europol pallets and a passenger car. Directly behind each of the vehicles involved in the accident there is another car which stops at a distance of 1.0 m. Approximately 300 litres of burning diesel are discharged from the truck's fuel tank, which is simulated by using approximately 400 litres of isopropanol. A 10 m-² burning pool forms underneath the truck. Other objectives of the large scale fire test are the validation of the CFD models and the evaluation of the progression of the thermal release ratios estimated for the simulation. The thermal release ratios generated in the test are determined and evaluated using various models.
Autobahnfahrbahnen aus unbewehrtem Beton sind durch Quer- und Längsfugen in Plattenelemente mit Standardmaßen unterteilt, wobei die Abmessungen auf Erfahrungswerten beruhen. Im Zuge des Forschungsprojektes wurde das Schwingungs- und Verformungsverhalten einer Betonfahrbahnplatte untersucht, um so Erkenntnisse über das dynamische Verhalten einer Betonfahrbahnplatte unter Verkehr zu erlangen. Zu diesem Zweck wurde eine neuartige Messstelle mit Beschleunigungssensoren zur Erfassung der Plattenbewegung errichtet. Einsenkungsdaten der Platte wurden durch Integration der Beschleunigungswerte bestimmt. Zunächst konnten bei der Auswertung der gemessenen Daten wertvolle Empfehlungen für Verbesserungsmöglichkeiten der Messeinrichtung bezüglich Auswahl, Anzahl, Platzierung der Sensoren, Ausführungsdetails und zweckmäßigerweise zusätzlich zu installierender Messsysteme gewonnen werden. Nach Analyse der Messdaten hinsichtlich Einsenkung und spektraler Leistungsdichte konnte festgestellt werden, dass ein harmonisches Schwingungsverhalten oder ein Nachschwingen der Platte durch die starke Dämpfung des Systems ausgeschlossen werden kann. Des Weiteren wurde ein FE-Modell der Betonplatte mit den realen Abmessungen und Stoffkennwerten erstellt und nach dem Verfahren von Westergaard sowie anhand der Messwerte kalibriert. An diesem können Variationen von Länge, Breite und Höhe der Platte berechnet und das Verhalten bei Überfahrt eines Lkw untersucht werden. Hierbei zeigte sich ein dominanter Einfluss des Untergrundes auf das Schwingungs- und Verformungsverhalten der Betonfahrbahnplatte. Bei Variationen der Plattenlänge konnte ein Einfluss der Länge auf die Relativbewegung in der Fuge ermittelt werden. Hier ist besonders bei Längen von mehr als 5 m eine starke Zunahme zu bemerken. Durch Betrachten des Plattenverhaltens beim Lastübergang zwischen den Platten konnte die Theorie des Pumpens und der dadurch verursachten Stoffumlagerung bestätigt werden.
Research to inform policy is often challenged with how to genuinely use and implement research findings in decision-making and policy-planning. To begin with, the dialogue between researchers and decision-makers is essential to ensure profound understanding and legitimate interpretations of the results. Furthermore, the step to drawing practical conclusions and processing them into actions can only succeed if research findings are diffused to decision-making levels with influence on the matter, and mechanisms to knowledge transfer in the presence of a stable, favourable policy environment exist. Research investments into the topic of electromobility in Europe are substantial, and subtopics aiming to inform national policy-makers address a complex set of aspects from environmental and societal to technological and economic. This paper has a two-fold objective, the first of which is to present the results of scenarios to explore electromobility deployment in Finland, Germany and the European Union. The second is to discuss the challenges and solutions to bridge the gap from research findings towards decision-making and policy-planning, using the authors' electromobility scenario work as an example. The electromobility scenarios were built using the VECTOR21 model (Mock, 2010), and the rationale was to simulate vehicle sales and markets under different policy settings and calculate the most economical solution to fulfill regulation on COâ‚‚ emissions as set by the European Commission (2009). The model allows calculating the market diffusion of alternative powertrain technologies to the European market until 2030, taking into account different taxation schemes, incentives and other country-specific characteristics. The authors also present the cost-benefit-analysis of the modelling results to assess the different scenarios and to show variation between regions regarding profitability of alternative technological or political support and interventions. To proceed from research findings towards decision-making and policy-planning, the authors made observations relating to transfer of research knowledge and interpretation of their electromobility scenario results in national policy contexts. An evaluation of how the function of research to inform policy in this case succeeded is provided. In addition, the influence of expert opinions on the political decision-making process will be discussed through experiences from an expert questionnaire conducted to survey the importance of costs, time requirement, acceptance and other criteria of promotion measures of electromobility.
One main objective of the EU-Project SENIORS is to provide improved methods to assess thoracic injury risk to elderly occupants. In contribution to this task paired simulations with a THOR dummy model and human body model will be used to develop improved thoracic injury risk functions. The simulation results can provide data for injury criteria development in chest loading conditions that are underrepresented in PMHS test data sets that currently proposed risk functions are based on. To support this approach a new simplified generic but representative sled test fixture and CAE model for testing and simulation were developed. The parameter definition and evaluation of this sled test fixture and model is presented in this paper. The justification and definition of requirements for this test set-up was based on experience from earlier studies. Simple test fixtures like the gold standard sled fixture are easy to build and also to model in CAE, but provide too severe belt-only loading. On the other hand a vehicle buck including production components like airbag and seat is more representative, but difficult to model and to be replicated at a different laboratory. Furthermore some components might not be available for physical tests at later stage. The basis of the SENIORS generic sled test set-up is the gold standard fixture with a cable seat back and foot rest. No knee restraint was used. The seat pan design was modified including a seat ramp. The three-point belt system had a generic adjustable load limiter. A pre-inflated driver airbag assembly was developed for the test fixture. Results of THOR test and simulations in different configurations will be presented. The configurations include different deceleration pulses. Further parameter variations are related to the restraint system including belt geometry and load limiter levels. Additionally different settings of the generic airbag were evaluated. The test set-up was evaluated and optimized in tests with the THOR-M dummy in different test configurations. Belt restraint parameters like D-ring position and load limiter setting were modified to provide moderate chest loading to the occupant. This resulted in dummy readings more representative of the loading in a contemporary vehicle than most available PMHS sled tests reported in the literature. However, to achieve a loading configuration that exposes the occupant to even less severe loading comparable to modern vehicle restraints it might be necessary to further modify the test set-up. The new generic sled test set-up and a corresponding CAE model were developed and applied in tests and simulations with THOR. Within the SENIORS project with this test set-up also volunteer and PMHS as well as HBM simulations are performed, which will be reported in other publications. The test environment can contribute in future studies to the assessment of existing and new frontal impact dummies as well as dummy improvements and related instrumentation. The test set-up and model could also serve as a new standard test environment for PMHS and volunteer tests as well as HBM simulations.
Test and assessment procedures for passive pedestrian protection based on developments by the European Enhanced Vehicle-safety Committee (EEVC) have been introduced in world-wide regulations and consumer test programmes, with considerable harmonization between these programmes. Nevertheless, latest accident investigations reveal a stagnation of pedestrian fatality numbers on European roads running the risk of not meeting the European Union- goal of halving the number of road fatalities by the year 2020. The branch of external road user safety within the EC-funded research project SENIORS under the HORIZON 2020 framework programme focuses on investigating the benefit of modifications to pedestrian test and assessment procedures and their impactors for vulnerable road users with focus on the elderly. Injury patterns of pedestrians and cyclists derived from the German In-Depth Accident Study (GIDAS) show a trend of AIS 2+ and AIS 3+ injuries getting more relevant for the thorax region in crashes with newer cars (Wisch et al., 2017), while maintaining the relevance for head and lower extremities. Several crash databases from Europe such as GIDAS and the Swedish Traffic Accident Data Acquisition (STRADA) also show that head, thorax and lower extremities are the key affected body regions not only for the average population but in particular for the elderly. Therefore, the SENIORS project is focusing on an improvement of currently available impactors and procedures in terms of biofidelity and injury assessment ability towards a better protection of the affected body regions, incorporating previous results from FP 6 project APROSYS and subsequent studies carried out by BASt. The paper describes the overall methodology to develop revised FE impactor models. Matched human body model and impactor simulations against generic test rigs provide transfer functions that will be used for the derivation of impactor criteria from human injury risk functions for the affected body regions. In a later step, the refined impactors will be validated by simulations against actual vehicle front-ends. Prototyping and adaptation of test and assessment procedures as well as an impact assessment will conclude the work of the project at the final stage. The work will contribute to an improved protection of vulnerable road users focusing on the elderly. The use of advanced human body models to develop applicable assessment criteria for the revised impactors is intended to cope with the paucity of actual biomechanical data focusing on elderly pedestrians. In order to achieve optimized results in the future, the improved test methods need to be implemented within an integrated approach, combining active with passive safety measures. In order to address the developments in road accidents and injury patterns of vulnerable road users, established test and assessment procedures need to be continuously verified and, where needed, to be revised. The demographic change as well as changes in the vehicle fleet, leading to a variation of accident scenarios, injury frequencies and injury patterns of vulnerable road users are addressed by the work provided by the SENIORS project, introducing updated impactors for pedestrian test and assessment procedures.
International und europäisch besteht zunehmend die Tendenz, bei besonderen Anforderungen sowohl bei neuen als auch bei bestehenden Tunneln stationäre Brandbekämpfungsanlagen (BBA) als Ausstattungsmerkmal mit zu berücksichtigen. Das vorrangige Schutzziel, auf das der Einbau einer BBA hierbei abzielt, ist die Unterstützung der Fremdrettung oder der Bauwerksschutz. Untersuchungen zu BBA fokussierten daher bislang mehr auf die Wirksamkeit dieser Anlagen, ihre Einbindung in die Tunnelsicherheitssysteme und ihre Wechselwirkung mit anderen technischen Systemen im Tunnel. Der Einfluss einer aktivierten Anlage auf das menschliche Verhalten, speziell im Zuge der Selbstrettungsphase, ist demgegenüber in den Untersuchungen weitgehend unberücksichtigt geblieben. Im Rahmen mehrerer Forschungsvorhaben sind nunmehr speziell diese Fragestellungen untersucht worden. Im Vorhaben FE 15.0563/2012/ERB "Wirksamkeit automatischer Brandbekämpfungsanlagen in Straßentunneln" beantworten die durchgeführten psychologischen Untersuchungen des menschlichen Verhaltens und Probandenversuche in virtueller Realitaet zuvor offene Fragen über das Verhalten des Nutzers bei einer aktivierten Anlage. Zur Einbeziehung auch haptischer Effekte wurden Realversuche in verschiedenen Tunnelumgebungen durchgeführt. Probandenversuche mit real aktivierten BBA sind Gegenstand zweier weiterer Forschungsvorhaben: FE 89.0299/2014 "Einfluss einer aktivierten Brandbekämpfungsanlage (DLS) auf das Reaktions- und Fluchtverhalten der Verkehrsteilnehmer" und FE 15.0607/2014/ERB "Analyse des Reaktions- und Fluchtverhaltens von Tunnelnutzern bei einer aktivierten Brandbekämpfungsanlage anhand von Realversuchen". Gegenstand der Vorhaben ist die Untersuchung des Verhaltens der Tunnelnutzer bei einer aktivierten Brandbekämpfungsanlage vom Typ Druckluftschaum (DLS) und Wassernebel (WN). Im vorliegenden Bericht sind die Ergebnisse aus den drei Forschungsvorhaben bezogen auf das menschliche Verhalten zusammengefasst und vergleichend gegenübergestellt. Hiermit stehen nunmehr abgesicherte Aussagen über den Einfluss einer aktivierten Anlage auf das menschliche Verhalten bei Aktivierung von BBA in einem Straßentunnel speziell im Hinblick auf die Selbstrettungsphase zur Verfügung. Sowohl die Analyse des Verhaltens als auch die Befragungen liefern erste Anhaltspunkte dafür, dass die Aktivierung einer BBA in einem Straßentunnel das Verhalten der Tunnelnutzer eher nicht negativ beeinflusst, solange Teile der Infrastruktur des Tunnels auf die Aktivierung einer BBA abgestimmt werden. Dabei ist vor allem eine gut verständliche Durchsage wichtig, damit auch Personen im direkten Einflussbereich der BBA ihr Fahrzeug verlassen. Der Bericht soll eine Hilfestellung bei der Einschätzung des Einflusses dieser Anlagen auf das menschliche Verhalten in Tunneln unter besonderer Berücksichtigung des Schutzziels Selbstrettung bieten.
Im Rahmen dieses Forschungsvorhabens wurde ein Verfahren entwickelt und validiert, mit dem sich reale Emissionsfaktoren für motorisierte Zweiräder in der Systematik des HBEFA generieren lassen. Das Verfahren basiert auf Fahrzeug-Emissionsmessungen in realen Testzyklen, vermessen am Rollenprüfstand oder auf der Straße, als Eingabe für ein Simulationsmodell. Das Modell erzeugt aus den Messungen Motorkennfelder, in denen die Abgasemissionen und der Kraftstoffverbrauch über normierter Motordrehzahl und normierter Motorleistung abgelegt werden. Für jedes gemessene Kfz ergibt sich ein normiertes Emissions-Motorkennfeld. Aus den einzelnen Kennfeldern können dann Durchschnittskennfelder je Fahrzeugkategorie (z.B. Motorrad über 500ccm, EURO 3) gebildet werden. Die Motordrehzahl muss in den Emissionstests entweder gemessen, oder aus Geschwindigkeit, Gang, Reifenumfang und Übersetzungen berechnet werden. Die Motorleistung kann mittels gemessenem CO2-Massenstrom und der Drehzahl aus "generischen CO2-Kennfeldern" ermittelt werden, da im Allgemeinen keine gemessene Leistung vorliegt. Um mit dem Modell dann Emissionsfaktoren für beliebige Fahrzyklen zu bestimmen, wird die Motorleistung aus der Fahrzeuglängsdynamik, den Verlusten im Antriebstrang und dem Leistungsbedarf von Nebenaggregaten aus dem jeweils vorgegebenen Geschwindigkeits- und Steigungsverlauf berechnet. Zur Bestimmung der Drehzahl wird zuerst ein passender Gang berechnet und dann aus den Übersetzungen die Motordrehzahl. Steht die geforderte Motorleistung in keinem Gang zur Verfügung, wird die Beschleunigung im betroffenen Zeitschritt so reduziert, dass sich ein Volllastbetrieb ergibt. Die Berechnungen erfolgen in 1Hz Auflösung. Für jede Sekunde werden dann aus dem zugehörigen Motorkennfeld die Emissionen entsprechend der Drehzahl und Leistung interpoliert. Die integrierten Emissionswerte über den Zyklus ergeben die Summenemissionen, die Division durch die zurückgelegte Strecke die Emissionsfaktoren in g/km. Die Methode wurde im Simulationsprogramm PHEM implementiert. Da PHEM bereits in einem ähnlichen Verfahren Emissionsfaktoren für PKW, LNF und SNF berechnet, war der Zusatzaufwand zum Einbau von Zweirädern nieder und alle Zusatzfunktionen von PHEM können auch für Zweiräder verwendet werden (z.B. Dynamikkorrekturen, automatisierte CO2-basierte Kennfelderzeugung, Batch-Modus, etc.). In dem Projekt wurde die Modellentwicklung und Validierung anhand von 4 gemessenen Zweirädern durchgeführt. Die Tests umfassten Abgasmessungen auf einem Rollenprüfstand sowie On-Road-Messungen mittels PEMS. Die Messkampagne wurde auch genutzt, um einen Vorschlag für ein einheitliches Minimalmessprogramm zur Bestimmung von Emissionsfaktoren von Zweirädern zu erarbeiten. Dazu wurden umfangreiche Fahrversuche im realen Betrieb durchgeführt, die gemessenen Zyklen in Teilstücke verschiedener Verkehrssituationen unterteilt und je Verkehrssituation ein repräsentatives Teilstück bestimmt. Diese wurden dann zu "Real World Rollenzyklen" zusammengefügt. Bei einem Motorradzyklus ist auch ein sportlicher Fahranteil mit Steigung enthalten. Damit ist sichergestellt, dass die Motorkennfelder mit diesen Rollentests gut abgedeckt sind und bei der Berechnung von Emissionsfaktoren keine Extrapolationen von Emissionswerten erforderlich sind. Die am Markt befindlichen PEMS Systeme sind für die Verwendung bei Zweirädern wegen deren Gewicht und Baugröße nicht für alle Fahrzeuge geeignet. PEMS Messungen sind vorerst nur bei größeren Motorrädern im realen Verkehr möglich. Die Emissionskennfelder enthalten jeweils CO, CO2, NOx, HC sowie optional auch die vom FTIR gemessenen Komponenten und Partikelanzahl. Die nicht limitierten Abgaskomponenten aus der FTIR Messung können, wegen der teilweise sehr niederen Emissionsniveaus, nur unsicher zeitaufgelöst gemessen und simuliert werden, so dass hier die Verwendung von Zyklusmittelwerten in [g/km] oder von mittleren Prozentwerten an den HC und NOx Emissionen empfohlen wird. Mit der entwickelten Methode und der Software PHEM bestehen nunmehr die Grundlagen, Emissionsfaktoren für Zweiräder in gleicher Qualität wie sie bei PKW und Nutzfahrzeugen bereits Standard ist, zu gerieren. Die Methoden und mögliche gemeinsame Messprogramme werden in der ERMES Gruppe bereits diskutiert und werden hoffentlich schon 2018 zu einer deutlichen Verbreiterung der Datengrundlage zum Emissionsverhalten von Zweirädern führen.
Das Fahrzeugsegment der leichten Nutzfahrzeuge (LNF) hat in den vergangenen Jahren in Deutschland stark an Bedeutung gewonnen. Der Bestand ist im Jahr 2014 auf rund 2,1 Mio. Fahrzeuge angewachsen " das entspricht einem Wachstum von +133 % gegenüber 1990. Die Fahrleistungen der LNF haben nach den Annahmen für TREMOD im gleichen Zeitraum sogar um +170 % zugenommen. Die zunehmende Bedeutung der LNF sowie die heutige Vielfalt der Einsatzzwecke spiegeln sich in der Modellierung der Emissionen von LNF in Deutschland zum Teil nicht wieder. Die Datengrundlagen für das Verkehrsemissionsmodell TREMOD (Transport Emission Model) sowie für das Handbuch für Emissionsfaktoren des Straßenverkehrs (HBEFA) sind teilweise mehr als 20 Jahre alt. Die Aufteilung der Fahrleistung nach Verkehrssituationen und Längsneigungsklassen geht beispielsweise auf eine Analyse von HEUSCH/BOESEFELDT aus dem Jahr 1996 zurück. Die Fahrzyklen, die den Verkehrssituationen und damit auch den Emissionsfaktoren zugrunde liegen, basieren gerade für leichte Nutzfahrzeuge auf wenigen Daten oder sind von Pkw abgeleitet. Zudem stehen nur eine beschränkte Anzahl von Emissionsmessungen für LNF zur Verfügung, auf deren Basis die Emissionsfaktoren für HBEFA abgeleitet werden. Die Gesamtfahrleistung (Inlandsfahrleistung) der LNF in TREMOD basiert im Wesentlichen noch auf der Fahrleistungserhebung (FLE) 2002. Die Inlandsfahrleistung der LNF war hierbei etwa gleich hoch wie die Inländerfahrleistung. Jedoch wurde nur ca. die Hälfte der Fahrleistungen auf den freien Strecken gemäß Straßenverkehrszählung der BASt erfasst und die Differenz den Innerorts- und Gemeindestraßen in TREMOD zugeordnet. Die Fortschreibung der Fahrleistungen von 2002 bis 2014 erfolgte u.a. über die Straßenverkehrszählungen und die Bestandsentwicklung. Auswertungen der (bei Berichtslegung noch nicht definitiv vorliegenden) Fahrleistungserhebung 2014 müssen zeigen, ob die angenommenen Entwicklungen der Gesamtfahrleistung der LNF sowie pro Straßenkategorie plausibel sind. Vorläufige Ergebnisse der FLE 2014 zeigen deutlich höhere LNF-Inlandsfahrleistungen als aktuell in TREMOD hinterlegt. Eine Detailanalyse und Interpretation der Ergebnisse konnte aber im Rahmen dieses Projektes noch nicht erfolgen. Neben den bisher in TREMOD verwendeten Quellen wurden weitere Fahrleistungsdaten untersucht. Für das Jahr 2013 veröffentlichte das Kraftfahrtbundesamt (KBA) erstmals Inländerfahrleistungen je Fahrzeugkategorie und Fahrzeugalter, basierend auf Tachostandinformationen von 26,5 Mio. deutschen Kraftfahrzeugen. Es wird empfohlen die Fahrleistungsstatistik vom KBA in zukünftige TREMOD-Aktualisierungen einzubeziehen. Für die Herleitung der in HBEFA den LNF zugrunde gelegten Fahrmustern wurde bislang nicht nach Pkw und LNF unterschieden. Vergleiche der verfügbaren LNF- und Pkw-Fahrmuster bezüglich der Geschwindigkeit und der Wegedauer zeigen leichte Abweichungen in der Form, dass LNF tendenziell öfter mit geringeren Geschwindigkeiten und kürzerer Wegedauer unterwegs sind als Pkw. Die Unterschiede sind jedoch durchwegs gering. Es können auf der Basis der verfügbaren Datengrundlagen keine eigenständigen LNF-Fahrzyklen abgeleitet werden. Die Emissionsfaktoren in HBEFA werden über das Simulationsmodell PHEM der FVT-TU Graz generiert. Aufgrund der unzureichenden Datenlage konnten bisher für PHEM keine LNF-spezifischen Emissionskennfelder verwendet werden, d.h. es wurden modifizierte Pkw-Kennfelder für die Modellierung der Emissionsfaktoren verwendet. Mittlerweile stehen weitere LNF-Messungen für die Herleitung von Emissionskennfeldern zur Verfügung. Für die hinsichtlich der heutigen Fahrleistungen relevanten LNF-Fahrzeugschicht (N1-III-Diesel-Euro-5) liegen beispielsweise aktuell 10 zeitlich hochaufgelöste Emissionsmessungen vor, welche bei der nächsten Aktualisierung von HBEFA genutzt werden können.
Bus or heavy vehicle passenger accidents are rare events, compared with car accidents, but sometimes leads to a large number of victims especially in rollover crash scenarios. Two accidents occurred in Portugal in 2007 and 2013 in which 28 people died and more than 50 are injured, shown the importance of the investigation of such accidents. For the investigation of these accidents multidisciplinary teams are constituted with engineers and police officers. All the factors involved are taken into consideration including road design, traffic signs, maintenance and hardware, human factors, and vehicle factors. In this work a methodology to an accurate collection of the data is proposed. From the information collected the accident is reconstructed using the PC-CrashTM software. From this all the contribution factors are determined and recommendations to mitigate these crashes are listed. These two accidents are rollover accidents and the analysis of the injuries and its correlation with the use of retention systems is very important. From the medical data and with the dynamics of the accident determined simulations of the occupants with biomechanical models are carried out in order to evaluate the effect of the retention systems in the injuries. This analysis is based on injury criteria (such as Abbreviated Injury Score (AIS) or Injury Severity Scale (ISS)). With this it is possible to determine if the seat belt was worn or not.
Since its creation in 2011 the Pre-Crash-Matrix (PCM) offers the possibility to observe the pre-crash phase until five seconds before crash for a wide range of accidents. Currently the PCM contains more than 8.000 reconstructed accidents out of the GIDAS (German In-Depth Accident Study) database and is enlarged continuously by more than 1.000 cases per year. Hence, a detailed investigation of active safety systems in real accident situations has been made feasible. The PCM contains all relevant data in database format to simulate the pre-crash phase until the first collision of the accident for a maximum of two participants. This includes the definition of the participants and their characteristics, the dynamic behavior of the participants as time-dependent course for five seconds before crash as well as the geometry of the traffic infrastructure. The digital sketch of the accident and information from GIDAS as well as from supplementary databases represent the main input for the simulation of the pre-crash phase of an accident with the VUFO simulation model VAST (Vufo Accident Simulation Tool). This simulation in turn embodies the foundation of the PCM. The PCM underlies continual improvements and enhancements in consultation with its users. In addition to collisions of cars with other cars, pedestrians, bicycles and motorcycles the PCM now also covers car to object and car to truck collisions. The paper illustrates car to truck collisions as a showcase and explains perspectives for further developments. In 2016 a more detailed definition of the contour of the vehicle was added. Furthermore, the geometrical surroundings of the accident site will be provided in a new structure with a higher level of detail. Thus, a precise classification of road marks and objects is possible to further improve the support of developing and evaluating ADAS. This paper gives an overview about the latest developments of the PCM with its innovations and provides an outlook to upcoming enhancements. Besides potential areas of application for the development of ADAS are shown.
This work describes the results of the experimental activity, illustrating the driving behavior observed in different conditions, relating them to the different methods of ADAS intervention and comparing the driver behavior without ADAS. In the present study, driver behavior was studied in road accidents involving elderly pedestrians, with different ADAS HMIs, as a base to develop a driver model in near missing pedestrian accidents. A literature research was conducted with the aim of finding out the main influencing factors, including environment, boundary conditions, configuration of impact, pedestrian and driver information, when pedestrian fatalities occur and an analysis of frequent road accidents was conducted to get more detailed information about the driver- behavior. In order to obtain more detailed information about pedestrian accidents, real road accidents were reconstructed with multibody simulations on PC-Crash and, by the comparison between literature findings and reconstructions, a generic accident scenario was defined. The generic accident scenario was implemented on the full scale dynamic driving simulator in use at the Laboratory for Safety and Traffic Accident Analysis (LaSIS, University of Florence, Italy) in order to analyse the driving behaviors of volunteers, also considering the influence of ADAS devices. Forty-five young volunteers were enrolled for this study, resulting in forty valid tests on different testing scenarios. Two different scenarios consisted in driving with or without ADAS in the vehicle. Different kinds of ADAS, acoustic and optical, with different time of intervention were tested in order to study the different reactions of the driver. The tests showed some interesting differences between driver's behavior when approaching the critical situation. Drivers with ADAS reacted earlier, but more slowly, depending also on the type of alarm, and often with double reaction when braking. In fact, the results of the activity showed that with ADAS intervention the time to collision (TTC) increases, but the reaction time and braking modality change: a) there is a sort of "latency" time between the accelerator pedal release and the brake pressure; b) the brake pressure is initially less intense. So the driver only partially takes advance from the TTC increase. These differences were valued not only qualitatively, but quantitatively as well. This work revealed to be useful to improve the knowledge of drivers" behavior, in order to realize a driver model that can be implemented to help attaining and assessing higher levels of automation through new technology.
The advent of active safety systems calls for the development of appropriate testing methods. These methods aim to assess the effectivity of active safety systems based on criteria such as their capability to avoid accidents or lower impact speeds and thus mitigate the injury severity. For prospective effectivity studies, simulation becomes an important tool that needs valid models not only to simulate driving dynamics and safety systems, but also to resolve the collision mechanics. This paper presents an impact model which is based on solving momentum conservation equations and uses it in an effectivity study of a generic collision mitigation system in reconstructed real accidents at junctions. The model assumes an infinitely short crash duration and computes output parameters such as post-crash velocities, delta-v, force directions, etc. and is applicable for all impact collision configurations such as oblique, excentric collisions. Requiring only very little computational effort, the model is especially useful for effectivity studies where large numbers of simulations are necessary. Validation of the model is done by comparison with results from the widely used reconstruction software PC-Crash. Vehicles involved in the accidents are virtually equipped with a collision mitigation system for junctions using the software X-RATE, and the simulations (referred to as system simulations) are started sufficiently early before the collision occurred. In order to assess the effectivity, the real accident (referred to as baseline) is compared with the system simulations by computing the reduction of the impact speeds and delta-v.
For more than a decade, ADAC accident researchers have analysed road accidents with severe injuries, recording some 20,000 accidents. An important task in accident research is to determine the causative factors of road accidents. Apart from vehicle engineering and human factors, accident research also focuses on infrastructural and environmental aspects. To find out what accident scenarios are the most common in ADAC accident research and what driver assistance systems can prevent them, our first task was to conduct a detailed accident analysis. Using CarMaker, we performed a realistic simulation of accident scenarios, including crashes, with varying parameters. To begin with, we made an initial selection of driver assistance systems in order to determine those with the greatest accident prevention potential. One important finding of this study is that the safety potential of the individual driver assistance systems can actually be examined. It also turned out that active safety offers even much more potential for development and innovation than passive safety. At the same time, testing becomes more demanding, too, as new systems keep entering the market, many of them differing in functional details. ADAC will continue to test all driver assistance systems as realistically as possible so as to be able to provide advice to car buyers. Therefore, it will be essential to develop and improve test conditions and criteria.
Whiplash injuries are characterized by the high variability of its symptoms and by the subjectivity of its diagnosis, which sometimes leads to frauds perpetrated by victims of rear-end impacts. It is estimated that whiplash injuries cost annually about 10.000 million Euros in Europe. Therefore, the aim of this study was to investigate the influence of the dynamics of the accident in which the victim was involved in the probability of development of whiplash associated injuries. In the presented methodology, first an accident reconstruction is performed where the dynamics of the accident is determined. This is carried out using the software PC-Crash, police and insurance companies' data. Then biomechanical injuries criteria related with whiplash injuries are evaluated. For the evaluation of the probability of having whiplash injuries, the Neck Injury Criterion (NIC) of the victim and the mean acceleration of the vehicle were evaluated. Then, with medical reports, the results of the accident reconstruction are correlated with the reported injuries. Some examples are presented. The results obtained indicate that the study of the dynamics of the road accidents in which the victims were involved could be used as an auxiliary of the prognosis of whiplash injuries and is important for a precise diagnosis of this type of injuries.
This study investigates the protection offered by passive head-restraints with different stiffness and energy dissipation properties. For this purpose, computational multi-body models of a generic car seat and a biofidelic 50thpercentile male human for rear impact are used to study different seat designs and passive head-restraints. The validated seat-occupant model is also used in the design of two different car-seat models which are shown to effectively mitigate whiplash by utilising a crash-energy distribution technique. Five different passive head-restraints with varying stiffness (low-medium-high) and energy dissipation percentages (low-high) are successively attached to four different car-seat models. The simulation results indicate that the protection offered by head restraints is strongly dependent on the seat design. It has also been shown that the stiffness of the passive head-restraint has much more influence on whiplash-risk in comparison to its energy dissipation capacity.
Ziel der Untersuchung war es, eine Methodik für die HBS-konforme Durchführung und Auswertung von Simulationsstudien zu erarbeiten. Dazu wurden HBS-konforme Standardelemente in den Simulationsprogrammen BABSIM, VISSIM, Aimsun, Paramics und SUMO modelliert und an den Bemessungswerten des HBS kalibriert. Die Ermittlung der Kapazität erfolgte anhand der Identifikation von Zusammenbrüchen des Verkehrsflusses, die durch Steigerung der Verkehrsstärke auf bis zu 120 % der Kapazität nach HBS in der Simulation erzeugt wurden. An Teilknotenpunkten wurden sechs Verhältnisse der Verkehrsstärke auf der Hauptfahrbahn zur Verkehrsstärke des ein- bzw. ausfahrenden Stroms untersucht. Als Kriterium für die Übereinstimmung der in der Simulation ermittelten Kapazität und q-v-Beziehung mit dem HBS wurde eine maximale Abweichung von 5 % festgelegt. Die Fehlergrenze konnte mit den Simulationsprogrammen BABSIM, VISSIM, Aimsun und Paramics in der Regel eingehalten werden, während sich in SUMO größere Abweichungen ergaben. Die Übertragbarkeit der Parametersätze auf nicht HBS-konforme Bemessungssituationen wurde anhand der Daten realer Untersuchungsobjekte überprüft. Im Ergebnis werden Empfehlungen und Standardparameterkombinationen für die HBS-konforme Simulation des Verkehrsablaufs auf Autobahnen bereitgestellt, die als Ausgangsparameter für die Simulation nicht HBS-konformer Untersuchungsobjekte herangezogen werden können.
In der Untersuchung wurde der Einfluss des Schwerverkehrs auf den Verkehrsablauf an planfreien Knotenpunkten analysiert. Als Grundlage dienten Daten von Dauerzählstellen für die Analyse auf makroskopischer Ebene, ergänzt durch Messungen an hochbelasteten Knotenpunkten für eine mikroskopische Analyse des Schwerverkehrs. Für die Untersuchung hoher Schwerverkehrsanteile wurden außerdem Verkehrsflusssimulationen an ausgewählten Knotenpunkten mit dem Programm BABSIM durchgeführt. Makroskopisch wurden die Daten von Dauerzählstellen und aus der Simulation mit den Verfahren des HBS (2015) verglichen und vor allem bezüglich der Umrechnung in Pkw-Einheiten ausgewertet. Dabei zeigte sich, dass die bestehenden Verfahren auch für hohe Schwerverkehrsanteile anwendbar sind, der Einfluss des Schwerverkehrs auf die Kapazität mit dem bislang angesetzten Pkw-Gleichwert von 2,0 aber bei Schwerverkehrsanteilen größer oder gleich 20 % eher überschätzt wird. Weiterhin wurden Regressionsanalysen durchgeführt, die dazu dienten, eine Funktion der für die Einfahrt maßgebenden Belastung des rechten Fahrstreifens zu identifizieren. Diese Funktion diente als Eingangsgröße für die Kalibrierung und Erweiterung eines analytischen Modells, mit dem die Veränderung der Fahrstreifenaufteilung im Bereich von Ein- und Ausfahrten nachgebildet werden kann. Als weiterer Ansatz wurden die Verfahren der stochastischen Kapazitätsanalyse für die Untersuchung von planfreien Knotenpunkten erweitert. Für die Anwendung des Verfahrens ist eine sehr umfangreiche Datengrundlage erforderlich, die nicht immer verfügbar ist. Im Rahmen der mikroskopische Analyse des Schwerverkehrs an planfreien Knotenpunkten wurden empirisch erhobene Einzelfahrzeugdaten hinsichtlich des Fahrstreifenwechselverhaltens der Schwerverkehrsfahrzeuge im Bereich der Knotenpunkte und der Zeitlückenverteilungen in verschiedenen Abständen von der Trenninselspitze analysiert. Mithilfe dieser Auswertungen wurden die um den Aspekt des Schwerverkehrs erweiterten analytischen Modelle kalibriert.
Im Rahmen des Forschungsprojektes wurden für verschiedene Tunnel mit Rechteck- und Gewölbequerschnitt mit dem Regelquerschnitt RG 31t (bzw. RQ 10,5), die orts- und zeitabhängigen Verteilungen der Gastemperatur, der Gasgeschwindigkeit und Gaszusammensetzung, der adiabaten Decken- und Wandtemperaturen sowie der zeitliche Verlauf der Wärmefreisetzungsrate und des Durchwärmungsverhaltens bestimmt werden. Betrachtet wurden Tunnel mit konstanter Längsneigung von 3 % sowie ein Tunnel mit muldenfoermigem Längsprofil (Richtungs- und Gegenverkehr). Bezüglich der Austrittgeschwindigkeit wurden die Szenarien 20,6 kg/s und 300 kg/s unterschieden. Zusätzlich im Fall A ein mit Holzpaletten beladenen LKW und im Fall B zusätzlich noch weitere PKW und LKW berücksichtigt. In einem originalmaßstäblichen Großbrandversuch wurde zur Klärung offener, aus der Modellierung resultierender Fragen ein Unfall in einem Richtungsverkehrstunnel zwischen einem LKW, der mit ca. 3,7 t Europoolpaletten beladen war, und einem PKW nachgebildet. Insgesamt wurden 3 Mittelklasse-PKW im Versuchstunnel positioniert. Die Brandlast betrug ca. 123 GJ. Anhand durchgeführter Plattenbrandversuche wurde festgestellt, dass die Schichten aus spritzbarem Faserbeton des Systems RUB sowie die Fertigteilschutzschichten des Systems HOCHTIEF ein relativ geringes bzw. kein Abplatzverhalten aufweisen und bei Brandbeanspruchung jeweils einen signifikanten thermischen Schutz der Stahlbetonkonstruktion gewährleisten können. Es konnte gezeigt werden, dass Auswirkungen auf die Tragstruktur nicht größer sind als infolge eines Brands, dessen Temperatur-Zeit-Verlauf dem ZTV-ING-Verlauf entspricht. Es sei aber angemerkt, dass aus den Szenarien unter noch ungünstigeren Bedingungen (z.B. im Falle eingeschränkt funktionsfähiger Schlitzrinnen) Auswirkungen entstehen könnten, die nur durch den verlängerten ZTV-ING-Temperatur-Zeit-Verlauf abgedeckt wären.