Sonstige
Filtern
Dokumenttyp
- Konferenzveröffentlichung (29) (entfernen)
Schlagworte
- Test (29) (entfernen)
Institut
- Sonstige (29)
- Abteilung Fahrzeugtechnik (1)
This work describes the results of the experimental activity, illustrating the driving behavior observed in different conditions, relating them to the different methods of ADAS intervention and comparing the driver behavior without ADAS. In the present study, driver behavior was studied in road accidents involving elderly pedestrians, with different ADAS HMIs, as a base to develop a driver model in near missing pedestrian accidents. A literature research was conducted with the aim of finding out the main influencing factors, including environment, boundary conditions, configuration of impact, pedestrian and driver information, when pedestrian fatalities occur and an analysis of frequent road accidents was conducted to get more detailed information about the driver- behavior. In order to obtain more detailed information about pedestrian accidents, real road accidents were reconstructed with multibody simulations on PC-Crash and, by the comparison between literature findings and reconstructions, a generic accident scenario was defined. The generic accident scenario was implemented on the full scale dynamic driving simulator in use at the Laboratory for Safety and Traffic Accident Analysis (LaSIS, University of Florence, Italy) in order to analyse the driving behaviors of volunteers, also considering the influence of ADAS devices. Forty-five young volunteers were enrolled for this study, resulting in forty valid tests on different testing scenarios. Two different scenarios consisted in driving with or without ADAS in the vehicle. Different kinds of ADAS, acoustic and optical, with different time of intervention were tested in order to study the different reactions of the driver. The tests showed some interesting differences between driver's behavior when approaching the critical situation. Drivers with ADAS reacted earlier, but more slowly, depending also on the type of alarm, and often with double reaction when braking. In fact, the results of the activity showed that with ADAS intervention the time to collision (TTC) increases, but the reaction time and braking modality change: a) there is a sort of "latency" time between the accelerator pedal release and the brake pressure; b) the brake pressure is initially less intense. So the driver only partially takes advance from the TTC increase. These differences were valued not only qualitatively, but quantitatively as well. This work revealed to be useful to improve the knowledge of drivers" behavior, in order to realize a driver model that can be implemented to help attaining and assessing higher levels of automation through new technology.
For more than a decade, ADAC accident researchers have analysed road accidents with severe injuries, recording some 20,000 accidents. An important task in accident research is to determine the causative factors of road accidents. Apart from vehicle engineering and human factors, accident research also focuses on infrastructural and environmental aspects. To find out what accident scenarios are the most common in ADAC accident research and what driver assistance systems can prevent them, our first task was to conduct a detailed accident analysis. Using CarMaker, we performed a realistic simulation of accident scenarios, including crashes, with varying parameters. To begin with, we made an initial selection of driver assistance systems in order to determine those with the greatest accident prevention potential. One important finding of this study is that the safety potential of the individual driver assistance systems can actually be examined. It also turned out that active safety offers even much more potential for development and innovation than passive safety. At the same time, testing becomes more demanding, too, as new systems keep entering the market, many of them differing in functional details. ADAC will continue to test all driver assistance systems as realistically as possible so as to be able to provide advice to car buyers. Therefore, it will be essential to develop and improve test conditions and criteria.
For the determination of the road surface roughness common methods have been established, like Skid Resistance Tester (SRT) or the Sideway-force Coefficient Routine Investigation Machine (SCRIM). Both methods are used to measure a comparable and reliable maximum friction potential value and to assess the quality of the road surface. However, the comparison of the measurements under real conditions and the results of measurements with SRT and SCRIM showed only minor correlations. The paper shows the comparison between these standardised methods and real vehicle braking tests and discusses the results.
The objectives of this paper are the analysis of the accident risk of drivers brain pathologies (Mild Cognitive Impairment, Alzheimer- disease, and Parkinson- disease), and the investigation of the impact of driver distraction on the accident risk of patients with brain pathologies, through a driving simulator experiment. The three groups of patients are compared to a healthy group of similar demographics, with no brain pathology. In particular, 125 drivers of more than 55 years old (34 "controls"" and 91 "patients") went through a large driving simulator experimental process, in which incidents were scheduled to occur. They drove in rural and urban areas, in low and high traffic volumes and in three distraction conditions (undistracted driving, conversation with a passenger and conversation through a mobile phone). The statistical analyses indicated several interesting findings; brain pathologies affect significantly accident risk and distraction affects more the groups of patients than the control one.
Es werden erste Ergebnisse des von der Bundesanstalt für Straßenwesen (BASt) geförderten Forschungsprojekts "Hauptstudie zur Wirksamkeit von Tunnelwänden als Träger photokatalytischer Oberflächen" (FE 9.0184/2011/ARB) vorgestellt. Ziel war die Erarbeitung von technischen Lösungen zur Stickoxidreduktion an einem Tunnelstandort durch die Konzeptionierung und den Bau abgeschlossener photokatalytischer Reaktoren (Tunnelkassetten) sowie deren Validierung im Tunnel "Rudower Höhe" an der Bundesautobahn A113 in Berlin. Dabei wird künstliches UV-Licht als Energiequelle für den Schadstoffabbau eingesetzt. Es wird speziell über die Modellierungen berichtet, mit Hilfe derer die Tunnelkassetten sowohl strömungstechnisch als auch in Hinblick auf den photokatalytischen Abbauwirkungsgrad optimiert wurden.
Verschiedene Maßnahmen zur Verbesserung der Luftqualität in Städten waren bisher bei der Verminderung von Stickoxiden nur bedingt erfolgreich. Interessant ist, ob der Einsatz der Photokatalyse hier weiterhelfen kann. Photokatalytische Anwendungen wurden schon in einigen Pilotstudien untersucht, zum Beispiel an Straßen beziehungsweise Modell-Canyons sowie in Tunneln. Teilweise wurden international sehr positive Ergebnisse erzielt, geichzeitig liegen aus anderen internationalen Projekten Ergebnisse unterhalb der Messgenauigkeit vor. Die vorgestellten Ergebnisse werden anhand verschiedener Variablen betrachtet und die erwartbare Atmosphärenrelevanz diskutiert. Zusammengefasst wird, dass basierend auf bekannten Feldmessungen für die Photokatalyse eine mittlere NOx-Reduktion von nur wenigen Prozent (in Hauptstraßenschluchten) zu erwarten ist. Dieses Potenzial muss mit anderen Maßnahmen verglichen werden (Kosten/Nutzenanalyse). Materialien müssen vor ihrem Einsatz in der Atmosphäre sorgfältig auf ihre Aktivität untersucht werden. Erfüllen die Oberflächen die Voraussetzungen, um als aktiv eingestuft zu werden, ist ihr Einsatz zur Luftreinhaltung klar zu empfehlen.
Zur Ergänzung der bestehenden Routineverfahren in der forensischen Blutalkoholanalytik wurde ein massenspektrometrisches Verfahren mit d6-Ethanol als internem Standard entwickelt. Ziel war die Anwendung eines beweissicheren Bestimmungsverfahrens, bei dem Ethanol über die Retentionszeit und Substanzeigenschaften identifiziert wird. Die Pilotstudie belegt, dass die forensische Blutalkoholbestimmung durch Anwendung eines gaschromatographischen und massenspektrometrischen Verfahrens mit Dampfraumanalyse routinemäßig möglich ist. Im Gegensatz zum GC- und ADH-Verfahren ist die massenspektrometrische Blutalkoholbestimmung beweissicher. Die Autoren empfehlen die Aufnahme in die Richtlinien zur Bestimmung der Blutalkoholkonzentration für forensische Zwecke. Die Arbeit wurde vom Bund gegen Alkohol und Drogen im Straßenverkehr e.V. (B.A.D.S.) unterstützt.
Es besteht Einigkeit darüber, dass Blutalkoholkonzentrationen (BAK) ab 0,30 Promille experimentell nachweisbare Beeinträchtigungen der Fahrtüchtigkeit hervorrufen. Die vorliegende Arbeit soll fundierte Aussagen über das Ausmaß und die Qualität kognitiver Veränderungen bei niedrigen BAK (um 0,30 Promille) ermöglichen. Es wurden in einer doppelblinden, placebokontrollierten Studie 16 gesunde männliche Probanden untersucht. Die BAK wurden während der Versuche auf etwa 0,30 Promille eingestellt. Es wurden mittels umfangreicher neuropsychologischer Tests untersucht: das allgemeine Intelligenzniveau, subjektive Beeinträchtigungen, mögliche depressive Symptome, die allgemeine Leistungsfähigkeit, die Vigilanz, die geteilte Aufmerksamkeit, die Reaktionszeit und die Gedächtnisleistungen. Die biostatistische Auswertung erfolgte im 2-Perioden-Crossover-Design. Zusammenfassend zeigen die vorliegenden Ergebnisse, dass bereits bei BAK von etwa 0,30 Promille vor allem kognitive Funktionen, die insbesondere auf die Wahrnehmung und die Verarbeitung visueller Informationen angewiesen sind, vor allem je komplexer und zeitkritischer eine Aufgabe wird, wie etwa die Beherrschung einer kritischen Situation im Straßenverkehr, relevant beeinträchtigt sind.
Seit einigen Jahren steht mit dem pupillographischen Schläfrigkeitstest (PST) ein objektives Messverfahren zur Ermittlung der Tagesschläfrigkeit zur Verfügung, wobei die Zunahme der spontanen Schwankungen des Pupillendurchmessers unter Müdigkeit registriert wird. Es wurde eingesetzt bei verschiedenen Probandengruppen, die einem potenziell erhöhten Risiko von Vigilanzminderungen ausgesetzt sind: chronische Schmerzpatienten (n = 20) beziehungsweise substituierte Heroinabhängige (n = 52) unter Opioiden, ambulante Patienten unter Psychopharmaka (n = 32), Allergiker unter Antihistaminika (n = 40) und medizinisches Nachtdienst-Pflegepersonal (n = 40). Verglichen wurde unter anderem mit zwei Kontrollgruppen (n = 21, n = 10). Bei den Untersuchungen ergaben sich relativ normale Schläfrigkeitswerte bei ambulanten Psychopharmaka-Patienten und Allergikern. Teils exzessiv erhöhte Werte wurden dagegen insbesondere bei substituierten Heroinabhängigen (81 Prozent), opiatversorgten Schmerzpatienten (59 Prozent) und dem Nachtdienstpersonal (70 Prozent) festgestellt.
Die Ergebnisse der vorliegenden Studie zeigen, dass Patienten mit einer unbehandelten Aufmerksamkeitsdefizit/Hyperaktivitätsstörung in verstärktem Maße verkehrsrechtlich auffällig werden und sowohl häufiger Unfälle verursachen als auch Ordnungswidrigkeiten begehen. Die Ergebnisse zeigen weiterhin, dass sich eine medikamentöse Behandlung günstig auf die verkehrsrelevanten Leistungsfunktionen auswirkt und dadurch auch die Grundvoraussetzungen für eine verbesserte Fahrtüchtigkeit und Fahreignung ermöglicht.
Die Begutachtung der Fahreignung beinhaltet in Deutschland neben einer medizinischen Untersuchung und einer psychologischen Exploration gegebenenfalls auch die Anwendung anlassbezogener verhaltenswissenschaftlicher/psychologischer Testverfahren. Diese stellen keine isolierte Maßnahme dar, sondern sind Bestandteil eines Begutachtungsprozesses. Dabei stellt der sachgerechte Gebrauch von so genannten Grenzwerten unter Berücksichtigung der Einzelfallgerechtigkeit und der Einhaltung des Grundsatzes der Verhältnismäßigkeit eine unabdingbare Voraussetzung dar. Testwerte sind nicht absolut, sondern relativ und üben von daher einen eher geringen Einfluss auf das Gutachtenergebnis in Bezug auf eine Prognose des Verkehrsverhaltens aus. Im Bereich des Verkehrsverhaltens kommt es nicht entscheidend darauf an, ob eine im Milli- oder Nanobereich exakte Messgenauigkeit erreicht wird, sondern wie die verkehrsmedizinischen, verkehrspsychologischen, technischen und anderen Sachverständigen mit dem Messwert fachlich umgehen. So müssen im Bereich der Begutachtung der Fahreignung tätige psychologische und medizinische Sachverständige in der Lage sein, Befunde im Einzelfall fehler-, mangel- sowie widerspruchsfrei zu interpretieren. Dies beinhaltet auch, sich mit den Ergebnissen eines psychologischen Testverfahrens fach- und sachgerecht auseinanderzusetzen, nach Kompensationsmöglichkeiten zu suchen und gegebenenfalls eine psychologische Fahrverhaltensbeobachtung durchzuführen. Bei grenzwertigen Vorgaben handelt es sich nicht um "Cut-Offs", sondern um "kritische Grenzwerte", die im Zusammenhang mit mehreren anderen Faktoren zu werten sind.
Die Ergebnisse der vorliegenden Studie zeigen, dass die Art, wie ein Fahrer mit Belastungen im Straßenverkehr umgeht, in Zusammenhang steht mit seinem Fahrstil und den Fahrfehlern, die er macht. Dabei zeigt sich, dass insbesondere ein konfrontativer Bewältigungsstil die Konfliktneigung im Straßenverkehr erhöht und dass diese Fahrer nicht nur andere belasten, sondern dass dieser Bewältigungsstil auch dazu führt, dass diese Fahrer selbst mehr Stress und Belastungen erleben.
The current paper reports on the results of a pilot study aiming to investigate the effect of mobile telephone use on the driving performance of 5 amateur and 5 professional drivers. Their driving acuity was tested through a driving simulator. Analysis and interpretation of the results occurred comparing the drivers' driving performance while talking, reading messages and writing a message on the mobile phone (intervention time) with the drivers' driving performance engaged in no activity (control time). The variables affected by the mobile phone were the "steering", the "lane offset" and the "duration of lane offset". Moreover, the drivers involved in a car crash in the last five years appeared to differ from those who were not involved in a crash in both "lane offset" and "following distance". The results of this pilot study will inform the design of a large experimental study on 50 professional and 50 amateur drivers.
SEEKING is looking for answers regarding electric powered bicycles and their relation to traffic safety issues. Does a cyclist need "E"? Is it as risky as riding a moped or are E-bikes creating conflicts with other cyclists? The project described herein, funded by the Austrian Ministry of Transport, has the aim of seeking answers to these hot topics. The SEEKING-team shows an in-depth investigation of vehicle dynamic sensing, together with subjective feedback of test riders to detect similarities and differences between conventional cycling and E-biking. Following an overview on the international status quo, measurement runs and their analyses are performed to find a set of preventative measures to make (E-)biking safer. A specific focus is the detection of curve handling, stopping and acceleration phases as well as conflict studies on course-based test rides and "real world" tests on cycling paths (naturalistic riding).
The current Brussels EU Regulation No. 1235/2011, valid from May 30, 2012, has introduced an European Tyre Label with wet grip index G classes from A to G for passenger car tyres C1, light commercial vehicles tyres C2 and heavy truck- and bus tyres C3. Every wet grip class for each vehicle category has a defined band of numerical values for the wet grip index G. The legislated wet grip values G in this EU- Regulation are very low. The measured braking distances and corresponding impact speeds of the test vehicles are showing very critical results. Regulation No. 1235/2011 of the European Parliament and the Council for Type Approval of Vehicles (EU) should be changed in such a way, that for C1-tyres (normal passenger cars tyres) the minimum wet grip index G is 1.25. All C2-tyres (light commercial vehicles tyres) should at least meet a minimum wet grip index of G = 1.1. All C3-tyres (heavy trucks and buses tyres) should at least meet a minimum wet grip index of G = 0.95. Due to the missing lower limits for G in the wet grip class F for C1, C2 and C3 tyres according to Commission Regulation (EU) No. 1235/2011, officially valid from 30 May 2012, a tyre-to-road coefficient of adhesion in the extreme of 0 (zero) is legally permitted. This is an apparent flaw in above cited EU Regulation, which causes a potential danger to the road traffic safety for all motor vehicles in Europe with such tyres. The wet grip class F has to be removed urgently from said EURegulation, since a direct liability of the responsible EU-Commission can not be excluded.
Today's volumes of traffic require more and more responsibility from each individual road user in their interactions. Those who drive motor vehicles have the singular obligation to minimise the risk of accidents and hence the severity of injuries, particularly with a view to the most vulnerable road users such as motor bikes, bikes and pedestrians. Since responsible and pro-active driving depends first and foremost on the visual information relayed by our eyes and the visual channel this requires good command of the traffic and all-round visibility from our driver's seat. Granted that human error can never be fully excluded, improving visibility around the car is nevertheless an urgent priority. To do so, we need to rate visibility in the most realistic driving situations. Since the existing visibility metrics and methodology are not applicable to real-life driving situations, this study aimed at developing a new visibility rating methodology based on real-life accident scenarios. On the basis of the cases documented by the accident research project, this study analysed criteria indicative of diminishing visibility on the one hand and revealing some peculiarities in connection with the visibility issue on the other. Based on the above, the project set out to develop a rating methodology allowing to assess all-round visibility in various road situations taking into account both driver and road geometries. In this context, the assessment of visibility while turning a corner, crossing an intersection and joining traffic on a major road (priority through route) is of major importance. The first tests have shown that critical situations can be avoided by adapting the relevant geometries and technical solutions and that significant improvements of road safety can be derived therefrom.
New vehicle types are extensively tested to check almost all factors that influence ride and handling. With reference to the Association of German Car Tuners" (VDAT e.V.) valuations, approximately 10% of all cars in Germany are being modified by their owners. 28 % of those modifications" sales are divergent wheel-tire combinations, 13 % are tuning measures on the chassis suspension or wheel spacers. In almost all cases the singular modifications present a general permission for specific vehicles they have been tested in. Combined tuning measures, however, are often checked by just one inspector, following a procedure of mostly subjective assessment criteria. Today, critical attributes are only being observed, in case a vehicle is involved in an accident and the modifications are identified as crash causal factors or as a cofactor on the development of a crash. For the first time, a field study allows a survey of safety affecting chassis modifications. The test layout has to comply with some basic conditions. Different vehicle concepts with a wide margin of modifications are required to get a high transferability of the results. A total amount of more than 150 tested vehicles serves the same purpose. The tests are limited concerning the installation time of measurement techniques and the requirement that no damage, defilement or immoderate wear of the vehicles are accepted by their owners. Due to such factors as well as the driver Ìs acceptance, the vehicles are controlled by its owners instead of robots or test drivers. For keeping down the driver- influence, the lane has narrow boundaries and the driver has to drive in strictly adherence to the given instructions. After gathering all modifications, as well as static and kinematic parameters like the toe and camber angle, dynamic testing of predominantly lateral dynamics is conducted. Besides standardized tests like the ISO 3888-2 (Obstacle Avoidance) or the ISO 14512 (Braking on Surfaces with Split Coefficient of Friction), to test the influence of modified kingpin offsets caused by wheel spacers, some deviant tests are conducted. Those are required due to the demand of objective test results for road tests with vertical induced stimulation of the chassis suspension. Hence, new tests on corner braking with and without vertical stimulation have been developed. The interpretation of data includes thresholds, e.g. the maximum entrance velocity without hitting cones, on the one hand, and the analysis of characteristics of data concerning time and frequency range, "1-second values" and peak response times on the other hand. Besides the thresholds as indicators for the achievable velocities, which are mainly affected by friction coefficients, the vehicle reaction in the course of time characterizes the vehicle reaction in the threshold range and consequently the operational demands on the driver. The field study has started and promises the first long-range analysis of chassis modifications. The results offer a basis for hypothesis and resultant further test layouts for oncoming studies of the identified critical tuning measures.
Do learner gain sufficient braking capabilities at the end of education for collision avoidance?
(2013)
The paper describes a test design to evaluate the braking behaviour in the course of the driver education. The results show that the braking capabilities increased during the driver education and the learning effects are the same for males and females. The evaluation limit is set to 6 m/s-². At the beginning of education, 50% of the drivers do not reach this limit, although the driver education car is equipped with an emergency brake assist, which is regularly installed in all vehicles since 2009. After the education, 100% of the drivers can reach the limit. The results are mapped to a collision avoidance scenario.
A concept for Safe-Driving-Trainings with a focus on risky behavior and safety related attitudes has been evaluated. 519 participants have been tested before and after the training by means of a questionnaire with the topics: technical driving competence, awareness of risks, and propensity for anticipation. A control group (131 subjects) was used to check for the possibility of response artifacts. Three months later, 92 members of the treatment group and 25 members of the control group have been tested again. The results show significant positive changes in driving competence, risk awareness, and safety related attitudes, especially anticipation, due to the training. Compared to the control group the participants have become more risk aware and they regard of risk avoiding behavior as more important. The results show that this concept for Safe-Driving-Trainings has not only short-term but, more importantly, long-term positive effects on the safety-relevant attitudes and cognitions of young drivers.
Brücken in ungünstiger geographischer/geomorphologischer Lage " z.B. über Gewässer, in Einschnitten, Schattenlagen und Niederungsbereichen " neigen konstruktionsbedingt gegenüber den angrenzenden bodengebundenen Fahrbahnen zur vorzeitigen Glättebildung, die eine besondere Gefährdung der Verkehrsteilnehmer - vor allem im Spätherbst und im zeitigen Frühjahr - darstellt. Die Erneuerung der Straßenbrücke B 208 / Elbe-Lübeck-Kanal in der Ortslage Berkenthin im Kreis Herzogtum Lauenburg bot auf Grund ihrer besonderen kleinklimatischen Situation die Möglichkeit, im Rahmen eines Pilotprojektes - aufbauend auf den Ergebnissen des Forschungsprojektes 15.401 "Vermeidung von Glatteisbildung auf Brücken" der BASt " die Fahrbahntafel mittels oberflächennaher geothermischer Energie zu temperieren. Die bei Planung, Bau sowie in der nunmehr anlaufenden Nutzungsphase gewonnenen Erkenntnisse sollen den Straßenbaulastträgern Hinweise und Entscheidungshilfen geben, die Verkehrssicherheit wie auch die Nachhaltigkeit bei glättegefährdeten Brücken und Straßenabschnitten durch den Einsatz alternativer Energien zu erhöhen und gleichzeitig den Aufwand für den präventiven Winterdienst zu reduzieren. Der hierfür erforderliche Kapitaleinsatz ist eher in volkswirtschaftlicher Hinsicht und erst in zweiter Linie betriebswirtschaftlich zu bewerten.