Sonstige
Filtern
Dokumenttyp
Sprache
- Englisch (6) (entfernen)
Volltext vorhanden
- nein (6) (entfernen)
Schlagworte
- Messung (6) (entfernen)
Institut
This study aimed to better understand nitrate transport in the soil system in a part of the state of North Rhine-Westphalia, in Germany, and to aid in the development of groundwater protection plans. An advection-diffusion (AD) cell was used in a miscible displacement experiment setup to characterize nitrate transport in 12 different soil samples from the study area. The three nitrate sorption isotherms were tested to define the exact nitrate interaction with the soil matrix. Soils varied in their properties which in its turn explain the variations in nitrate transport rates. Soil texture and organic matter content showed to have the most important effect on nitrate recovery and retardation. The miscible displacement experiment indicated a decrease in retardation by increasing sand fraction, and an increase in retardation by increasing soil organic matter content. Soil samples with high sand fractions (up to 94 %) exhibited low nitrate sorption capacity of less than 10 %, while soils with high organic matter content showed higher sorption of about 30 %. Based on parameterization for nitrate transport equation, the pore water velocity for both sandy and loamy soils were significantly different (P < 0.001). Pore water velocity in sandy soil (about 4 x 10 high 3 m/s) was about 100 to 1000 larger than in loamy soils (8.7 x 10 high 5 m/s). On the other hand, the reduction in nitrate transport in soils associated with high organic matter was due to fine pore pathways clogged by fine organic colloids. It is expected that the existing micro-phobicity increased the nitrate recovery from 9 to 32 % resulting in maximum diffusion rates of about 3.5 x 10 high 5 m/s2 in sandy soils (sample number CS-04) and about 1.4 x 10 high 7 m/s2 in silt loam soils (sample number FS-02).
The Netherlands is on the way to change its existing skid resistance measuring method for its highway network from the Dutch RAW 72, a longitudinal force method, to the Sideway Force method. This method is described in the Technical Specification 15901-8 (SKM device) as well as 15901-6 (SCRIM device) and is in use in 9 European countries. The CEN TC 227 WG5 on Surface Characteristics is currently working on combining of these two technical Specifications into a European standard for Sideway-Force (SWF) measurement devices. The idea of this change in the Netherlands was perceived in 2013 and since then a lot of meetings have been held with the different Dutch decision makers as well as with countries which currently operate SWF devices. There was an intensive exchange of knowledge about these devices and their corresponding quality assurance systems, because the Netherlands wanted to incorporate and rely on an existing system of a neighbor country without losing their present level of quality. The Netherlands has therefore decided to incorporate the German SKM approach. The network monitoring with the new system will start in 2017. To ensure the quality of skid resistance measurements and further cooperation in this field, it has been decided to initiate an alliance between BASt and the Dutch road owner Rijkswaterstaat (RWS). This alliance will facilitate an exchange of research activities, calibration of the Dutch systems according to the existing German Standard as well as control measurements with a BASt-device on the Dutch network during the network monitoring. During 2016 also comparative measurements will be performed on a network level with the current Dutch device and with an SKM device to determine a conversion between the two and to be able to define new threshold values.
APT with the mobile load simulator MLS10 towards non-destructive pavement structural analysis
(2019)
In 2014 a research program has been started about non-destructive test methods to evaluate the structure of pavements. This task has been given to two research groups - first research group is led by RWTH Aachen University (Rheinisch-Westfälische Technische Hochschule) and the second by University of Siegen. This paper focuses on the initial findings of the running research program. The assessment of the existing infrastructure and its condition will be one of the main tasks during the next years in order to use the available budget for maintenance accurately and efficiently. Therefore, it is necessary to identify possible damages and examine their effects on the road construction. BASt (Federal Highway Research Institute) is using the Mobile Load Simulator MLS10 for accelerated pavement testing (APT) on different types of pavements. In addition to non-destructive test methods, sensors are applied to measure structural impacts. The overall objective of this research program is to develop a non-destructive test method that allows the calculation of the remaining life time and load cycles of pavements. To simulate realistic wheel loads in a short period of time the MLS10 on German full scale standard pavement constructions has been used. The first pavement test section was loaded with 3 x 10 high 6 50 kN wheel loads while the second, thinner pavement test section was loaded with 3 x 10 high 5 50 kN wheel loads. Both loads are equivalent to the pavement design load. Three different strategies have been used to analyze and monitor structural changes. The innovative measurements have been realized by the two research groups to collect data for their models. The RWTH Aachen collected data with twelve geophones aligned in a row parallel to the wheel path. The geophones measure the entire vertical deflection basin of the pavement surface that exists due to the passing real truck wheels. These measurements were done for different truck speeds and at different transverse distances to the wheel path. The University of Siegen collected data by using acceleration sensors on the surface of the road construction. After recording the data they were integrated into displacement signals and evaluated. Additionally to those measurements BASt used conventional equipment to monitor the pavement structure and surface characteristics. The measurements and evaluation tools used for the innovation program have a high potential to validate APT programs in the future. Based on this research it is possible to start further research activities to push the non-destructive evaluation of pavements structures - not only in APT - into an improved direction.
Federal highway A 26 in Germany : reinforced dams in soft soils - control method according DIN 1054
(2004)
In 2001 the construction of the Federal Highway A 26 in Lower Saxony (north of Germany) was started. In this area the underground is without any substantial bearing capacity as it consists of soft layers ( clay, peat) with a thickness of up to 12 m. Because it was not possible to exchange the soil neither completely nor partially pre-loading procedure (consolidation method) was chosen for this construction. Short- and long-term stability are ensured by the use of high-tensile fabrics for reinforcement at the dam basis. The vertical and horizontal deformations and the stress changes in the soil, caused by the pre-load procedure, has to be controlled by special geotechnical measurements. Additionally, in the higher parts of the dam the strain behaviour of the high-tensile fabrics is measured. These measurements form the basis for the application of the control method according DIN 1054. In this article, the special circumstances of this project are described. Further on the geotechnical measurements, the winning and evaluation of the necessary parameters of the subsoil, and the consequences of these data for the ongoing of the project are laid down. Intermediate results of the geotechnical measurements are described.
Measuring and characterizing airborne particulate matter (PM) is an important research area because PM can lead to impacts on health and to visibility reduction, material damage and groundwater pollution. In regard to road dust, suspension and re-suspension and the contribution of non-exhaust PM to total traffic emissions are expected to increase as a result of predicted climate scenarios. European environmental regulations have been enforced to reduce exhaust particle emissions from road traffic, but little attention has been paid to reducing non-exhaust coarse particle emissions due to traffic. Therefore, a monitoring program for coarse PM has been initiated in early 2013 to assess the predicted increase in the abundance of non-exhaust particles. Particle sampling was performed with the passive-sampler technique Sigma-2. The subsequent single-particle analysis allows for characterization of individual particles, determination of PM size distribution, and calculation of PM mass concentrations. Two motorways n ear Cologne (Koeln), Germany were selected as sampling sites, and the experimental setup in the field was realized with a so-called twin-site method. The present study reports single-particle analysis data for samples collected between May 31, 2013 and May 30, 2014. Coarse PM, generated through multi-source mechanisms, consists of, e.g., tire-wear, soot aggregates, and mineral dust. The highest mass concentration occurs at both motorways in spring, and the observed PM mainly contains traffic-abrasion particles. The field measurements show that the minimum PM concentration was found in the 5 to 12-°C temperature range, whereas the maximum concentration was observed in both the "5 to 5-°C and the 12 to 24-°C ranges, in agreement with previous laboratory measurements. Correlation between super-coarse (d p 10"80 μm, geometric equivalent diameter) PM concentration and precipitation displays a significant increase in concentration with decreasing number of precipitation events (dry weather periods).
New vehicle types are extensively tested to check almost all factors that influence ride and handling. With reference to the Association of German Car Tuners" (VDAT e.V.) valuations, approximately 10% of all cars in Germany are being modified by their owners. 28 % of those modifications" sales are divergent wheel-tire combinations, 13 % are tuning measures on the chassis suspension or wheel spacers. In almost all cases the singular modifications present a general permission for specific vehicles they have been tested in. Combined tuning measures, however, are often checked by just one inspector, following a procedure of mostly subjective assessment criteria. Today, critical attributes are only being observed, in case a vehicle is involved in an accident and the modifications are identified as crash causal factors or as a cofactor on the development of a crash. For the first time, a field study allows a survey of safety affecting chassis modifications. The test layout has to comply with some basic conditions. Different vehicle concepts with a wide margin of modifications are required to get a high transferability of the results. A total amount of more than 150 tested vehicles serves the same purpose. The tests are limited concerning the installation time of measurement techniques and the requirement that no damage, defilement or immoderate wear of the vehicles are accepted by their owners. Due to such factors as well as the driver Ìs acceptance, the vehicles are controlled by its owners instead of robots or test drivers. For keeping down the driver- influence, the lane has narrow boundaries and the driver has to drive in strictly adherence to the given instructions. After gathering all modifications, as well as static and kinematic parameters like the toe and camber angle, dynamic testing of predominantly lateral dynamics is conducted. Besides standardized tests like the ISO 3888-2 (Obstacle Avoidance) or the ISO 14512 (Braking on Surfaces with Split Coefficient of Friction), to test the influence of modified kingpin offsets caused by wheel spacers, some deviant tests are conducted. Those are required due to the demand of objective test results for road tests with vertical induced stimulation of the chassis suspension. Hence, new tests on corner braking with and without vertical stimulation have been developed. The interpretation of data includes thresholds, e.g. the maximum entrance velocity without hitting cones, on the one hand, and the analysis of characteristics of data concerning time and frequency range, "1-second values" and peak response times on the other hand. Besides the thresholds as indicators for the achievable velocities, which are mainly affected by friction coefficients, the vehicle reaction in the course of time characterizes the vehicle reaction in the threshold range and consequently the operational demands on the driver. The field study has started and promises the first long-range analysis of chassis modifications. The results offer a basis for hypothesis and resultant further test layouts for oncoming studies of the identified critical tuning measures.