Sonstige
Filtern
Dokumenttyp
Schlagworte
- Airbag (15) (entfernen)
Institut
- Sonstige (15)
- Abteilung Fahrzeugtechnik (2)
In the European Project FIMCAR, a proposal for a frontal impact test configuration was developed which included an additional full width deformable barrier (FWDB) test. Motivation for the deformable element was partly to measure structural forces as well as to produce a severe crash pulse different from that in the offset test. The objective of this study was to analyze the safety performance of vehicles in the full width rigid barrier test (FWRB) and in the full width deformable barrier test (FWDB). In total, 12 vehicles were crashed in both configurations. Comparison of these tests to real world accident data was used to identify the crash barrier most representative of real world crashes. For all vehicles, the airbag visible times were later in the FWDB configuration. This was attributed to the attenuation of the initial acceleration peak, observed in FWRB tests, by the addition of the deformable element. These findings were in alignment with airbag triggering times seen in real world crash data. Also, the dummy loadings were slightly worse in FWDB compared to FWRB tests, which is possibly linked to the airbag firing and a more realistic loading of the vehicle crash structures in the FWDB configuration. Evaluations of the lower extremities have shown a general increasing of the tibia index with the crash pulse severity.
The need of passive safety devices, able to reduce the accidents and the severity of injuries suffered by motorcyclist, distinctly arises from data on accident statistics. In this paper, the effectiveness of an airbag device fitted in the biker- garments has been verified through various numerical simulations. Two simple test conditions were defined, in order to investigate the performance of the device both for back and front impacts, and simulated at various impact speeds. With the aim of providing more information about the actual capability of the airbag to reduce the severity of the injuries, one of accident scenario described by ISO 13232:2005 has been also investigated, checking the real effectiveness of the airbag strap-based firing system too. Confrontation of injury indexes resulting from simulation with and without airbag made possible a realistic evaluation of the harm reduction induced by the airbag presence.
Mit der flächendeckenden Einführung des Beifahrerairbags ergab sich das Problem der nachträglich festgestellten Inkompatibilität mit rückwärts gerichten Kindersitzen. Zahlreiche tödliche Unfälle mit Babyschalen, insbesondere in den USA, führten unter anderem dazu, dass in den Mitgliedsstaaten der Europäischen Union die Beförderung von Kindern in einem rückwärtsgerichteten Kinderschutzsystem auf einem mit Frontairbag geschützten Autositz untersagt wurde, sofern der Airbag nicht deaktiviert wurde. Heute gibt es eine Vielzahl an Möglichkeiten, die dem Nutzer zur Abschaltung des Airbags zur Verfügung stehen. Mit der Notwendigkeit der Abschaltung ergibt sich die Gefahr zweier Arten der Fehlbenutzung: die Beförderung eines Kindes in einer Babyschale trotz aktivierten Airbags beziehungsweise die Mitfahrt eines erwachsenen Insassen trotz deaktivierten Airbags. Im Rahmen dieser Studie wurden zu den beiden Fehlbenutzungsarten Beobachtungs- und Befragungsstudien durchgeführt, Unfalldaten in Hinblick auf die Problematik der Fehlbenutzung der Airbagabschaltung analysiert und Versuche zur erneuten Bewertung des Risikos, das durch heutige und zukünftige Airbagsysteme ausgeht, durchgeführt. In den Umfragen ließen sich nur schwer Daten zum Missbrauch bei der Beförderung von Kindern mit Airbag auf dem Beifahrersitz erfassen. Es kommt insgesamt zu nur wenigen Fällen des Transports eines Kindes auf dem Beifahrersitz mit aktivem Airbag, was zum einen an der hohen Abschaltquote des Beifahrerairbags liegt, zum anderen an der Präferenz der Eltern, die Kinder auf dem Rücksitz zu transportieren. Der Großteil dieser Fehlbenutzungsfälle entsteht in älteren Pkw, die einen Werkstattaufenthalt für die Deaktivierung/Aktivierung erfordern. Keine Missbräuche beziehungsweise technische Fehler fanden sich bei den Systemen mit automatischer Sitzerkennung. Der überwiegende Anteil der Missbrauchsfälle bei den Modellen mit manueller Umschaltmöglichkeit geht offenbar auf Vergessen zurück. Der Missbrauch zweiter Art wird ebenfalls wirkungsvoll durch automatische Systeme verhindert. Bei dieser Beförderungskonstellation ergibt sich jedoch praktisch immer ein Problem, wenn der Beifahrerairbag in einer Werkstatt deaktiviert wurde. Die dadurch für einen erwachsenen Mitfahrer entstehende Gefährdung wird als weniger gravierend eingeschätzt. Bei der manuellen Umschaltung im Fahrzeug verbleibt ebenfalls ein Vergessensproblem wie beim Missbrauch erster Art. Auch die Unfallanalyse deutet auf eine geringe Fehlbenutzungsquote hin. Von den untersuchten GIDAS-Frontalaufprallunfällen mit über 300 betroffenen Kindern nutzten lediglich 24 Kinder den Beifahrerplatz in einem Auto, das mit einem Beifahrerairbag ausgestattet war. In den meisten Fällen war der Airbag vorschriftsmäßig deaktiviert. In den nachgewiesenen Fehlbenutzungsfällen waren die Unfallfolgen für die betroffenen Babys gering. Die untersuchten Einzelfälle zeigen jedoch die tödliche Gefahr, die vom Beifahrerairbag ausgehen kann. Auf der technischen Seite gab es im Lauf der letzten Jahre grundsätzliche Veränderungen im Bereich der Gestaltung des Beifahrerairbags. Während bei der früheren Einbauposition des Airbags die Schale direkt angeschossen wurde, entfaltet sich dieser heutzutage eher nach oben, stützt sich an der Windschutzscheibe ab und kommt danach erst mit der Schale in Kontakt. Da er in diesem Zustand aber schon weitestgehend voll entfaltet ist, besitzt er zu diesem Zeitpunkt kaum noch die Aggressivität, die bei den Beifahrerairbags der ersten Generation beobachtet werden konnte, und stellt somit wahrscheinlich eine geringere Gefahr für das Kleinkind in der Babyschale dar. Damit lässt sich ein deutlicher Trend in Richtung weniger gefährlicher Airbags erkennen. Der Originalbericht enthält als Anhänge den Abdruck des Expertenfragebogen, die Zusammenfassung der Expertenbefragung, den Umdruck der Online-Befragung sowie den Fragebogen der Feldbefragung "Kindersitze und Airbag auf dem Beifahrersitz". Auf die Widergabe dieser Anhänge wurde in der vorliegenden Veröffentlichung verzichtet. Sie liegen bei der Bundesanstalt für Straßenwesen vor und sind dort einsehbar. Verweise auf die Anhänge im Berichtstext wurden zur Information des Lesers beibehalten.
In North America, frontal crash tests in both the regulatory environment and consumer-based safety rating schemes have historically been based on full-width and moderate-overlap (40%) vehicle to barrier impacts. The combination of improved seat-belt technologies, notably belt tensioning and load limiting systems, together with advanced airbags, has proven very effective in providing occupant protection in these crash modes. Recently, however, concern has been raised over the contribution of narrower frontal impacts, involving primarily the vehicle corners, to the incidence of fatality and serious injury as a result of the potential for increased occupant compartment intrusion and performance limitations of current restraint systems. Drawing on data documented in the National Automotive Sampling System (NASS)/ Crashworthiness Data System (CDS) for calendar years 1999 to 2012, the present study examines the characteristics of existing and proposed corner crash test configurations, and the nature of real-world collisions that approximate the test environments. In this analysis, particular emphasis is placed on crash pulse information extracted from vehicle-based event data recorders (EDR's).
This paper gives an overview of the in-depth crash investigation activity conducted by the Centre for Automotive Safety Research (CASR) at the University of Adelaide, in South Australia. Recent changes in method include: an expansion in on-call hours for the crash investigation team, providing the option of a phone interview for crash participants to discuss the crash, and downloading objective crash data from vehicle airbag control modules. These changes have resulted in: increased representativeness of crashes by hour of day; a decrease in the over-representation of fatal crashes in our sample; an increase in the proportion of crashes that involved a pedestrian, bicycle or scooter (moped); an increase in the proportion of crash participants consenting to an interview; and an increase in the objective data available, through airbag control module downloads. Our in-depth crash investigations enabled research into road departures that found barriers were a more feasible solution than clear zones for eliminating serious and fatal injury resulting from run off road crashes.
Nowadays airbags are part of the standard equipment in almost all new cars. While airbags are saving an increasing number of people from severe injuries and death in moderate and high speed crashes, they do not completely prevent dashboard injuries. The most common mechanism in dashboard injuries is a posteriorly directed force to the proximal tibia with the knee flexed. This may occur during a motor vehicle frontal impact accident when a knee of the driver or the front-seat passenger strikes the dashboard. The posterior force can be combined with a abducting or rotational force leading to concomitant lateral or posterolateral injury. Car and airbag manufacturers therefore develop special inflatable systems to reduce the impact force in dashboard injuries. Every new inflatable system, however, has to be evaluated in out of position situations in which the system might cause injuries to certain body areas. Therefore, we investigated a new kneebag system in different critical seating positions of post mortem test subjects (PMTS). The tested knee airbag module is a folded airbag (18 litre volume) which is installed below the lower section of the instrument panel of a passenger car. Using four PMTS (2 male, 2 female, age 36"67) the following positions were tested: normal seating position, knee flexed >90 degrees and knee flexed <60 degrees in static deployment tests with direct contact. In addition a dynamic test (48.8kph, AAMA-pulse) was carried out with the PMTS belted in a normal seating position. The inflation phase and the impact of the system on the knee/lower leg were analysed by high speed videos. After the test the lower legs of the PMTS were examined by Xray and autopsy. All soft tissue injuries and bone fractures were recorded. All the tests could be evaluated. Except some superficial skin lesions in the impact area no fracture of the bones around the knee and no knee ligament and tendon injuries were observed. Neither video analysis nor autopsy of the PMTS showed any critical contact injuries caused by the inflation process of the bag. Therefore, it can be concluded that in the tested seating positions which are the most critical for the knee area the knee bag system is safe.
Within the process of integrating passenger airbags in the vehicle fleet a problem of compatibility between the passenger airbag and rear-facing child restraint systems was recognised. Especially in the US several accidents with children killed by the passenger airbag were recorded. Taking into account these accidents the deactivation of a present passenger airbag is mandatory if a child is carried in a rear-facing child restraint system at the front passenger seat in all member states of the European Union. This rule is in force since the deadline of 2003/20/EC at the latest. In the past a passenger airbag either could not be disabled or could only be disabled by a garage. Today there are a lot of different possibilities for the car driver himself to disable the airbag. Solutions like an on/off-switch or the automatic detection of a child restraint system are mentioned as an example. Taking into account the need for the deactivation of front passenger airbags two types of misuse can occur: transportation of an infant while the airbag is (still) enabled and transportation of an adult, while the airbag is disabled, respectively. Within a research project funded by BASt both options of misuse were analysed utilising two different types of surveys amongst users (field observations and interviews, Internet-questionnaires). In addition both analysis of accident data and crash tests for an updated assessment of the injury risk caused by the front passenger airbag were conducted. Both surveys indicate a low risk of misuse. Most of the misuse cases were observed in older cars, which offer no easy way to disable the airbag. For systems, which detect a child seat automatically, no misuse could be found. The majority of misuses in cars equipped with a manual switch were caused by reasons of oblivion. Also the accident analysis indicates a minor risk of misuse. From more than 300 cases of the GIDAS accident sample that were analysed, only 24 children were using the front passenger seat in cars equipped with a front passenger airbag. In most of these cases the airbag was deactivated. When misuse occurred the injury severity was low. However, when analysing German single accidents the fatality risk caused by the front passenger airbag became obvious. From the technical point of view, there were important changes in the design of passenger airbags in recent years. Not only volume and shape were modified, but also the mounting position of the entire airbag module was changed fundamentally. Even if these findings do not allow obtaining general conclusions, a clear tendency of less danger by airbags could be identified. For future vehicle development a safe combination of airbags and rear faced baby seats seems to be possible in the long term. This would mean that both types of misuse could be eliminated. For parents an easier use of child seat and car would be the result.
Motorcycle safety research
(2007)
Honda- global motorcycle sales exceeded the 10 million units mark since 2004, and further expansion is expected. As a responsibility for a company to provide mobility, Honda is focusing on motorcycle safety as top priority and has been working on various activities for both aspects of hardware and software. Here, we present Honda- activity for the safety technology of motorcycles. At present, Honda is promoting motorcycle safety in the four themes of prevention and collision safety such as safety education, recognition assistance, accident prevention and injury reduction. First, in the area of the safety education, the "Honda Safety Driving Promotion Center" was established in 1970, and motorcycle riders and vehicle driver trainings have been organized, and the traffic training centers are used as an actual practice field not only in Japan but also in many other regions in the world. Through our training activities, the new area of safety training with hardware assistance was developed and Honda- unique technology was accumulated such as the riding simulator which can provide experience of potentially dangerous situations without risk. Especially, the "riding trainer", the popular version of the riding simulator, was introduced at several motor shows in various countries and launched in September 2005. It was distributed first in Europe and is expected to expand globally aiming at 3000 units worldwide.. And in Europe, the newest version, which includes the suburban roads program, jointly developed with ADAC, will be released in near future. In the area of recognition assistance, "vehicle to vehicle communication technology" is under development using the advantage of being a manufacturer of both motorcycles and cars. This technology is under research as Honda "ASV-3" in Japan, and as part of C2C activity in Europe. As for the accident prevention, advanced brake systems for motorcycles to assist more effective brake operation have been expanded, Honda signed the European Road Safety Charter in April 2004 with the advanced brake systems commitment and furthermore, they are expanding according to vehicle characteristics and region. Then all models above 250 cc will have a version of the system by 2010. And as the last theme, "motorcycle airbag system" is introduced which is equipped on a mass production motorcycle for the first time in the world. It has been researched and developed for a long time as an injury reduction technology for collision accidents. Honda automobile technology was used for the research and development of the motorcycle airbag, and many specific issues such as the analysis of the collision conditions particular to motorcycles have been solved to realize today- success. It might be known that ADAC in-house crash test held in August this year confirmed the high effectiveness of the airbag system and showed a positive result. This motorcycle airbag system is equipped to the Honda Gold Wing and launched in North America in August, 2006. Also in Europe, it will be sold by the end of this year. Each theme of Honda motorcycle safety technology can be seen at the Honda booth.
Detailed anthropometric data of pregnant women have been collected and used in the development of a computational model of the pregnant occupant model "Expecting". The model is complete with a finite element uterus and multi-body fetus, which is a novel feature in the models of this kind. The computational pregnant occupant model has been validated and used to simulate a range of impacts. The strains developed in the utero-placental interface are used as the main criteria for fetus safety. Stress distributions due to inertial loading of the fetus on the utero-placental interface play a role on the strain levels. Inclusion of fetus model is shown to significantly affect the strain levels in the utero-placental interface. This series of studies has led to the design of seatbelt features specifically for the pregnant women to enable them use the seatbelt correctly and comfortably.
Neben der zunehmenden Bedeutung der aktiven Sicherheit bleiben Maßnahmen der passiven Sicherheit bei der Entwicklung moderner Kraftfahrzeuge unabdingbar. Die Weiterentwicklung von Maßnahmen zum passiven Fußgängerschutz war zunächst größtenteils durch Verbraucherschutztests wie zum Beispiel Euro NCAP oder JNCAP getrieben und ist nun auch durch gesetzliche Regelungen verpflichtend geworden. Im vorangegangenen Forschungsprojekt der BASt FE 82.229/2002 Schutz von Fußgängern beim Scheibenaufprall ist die Grundlage eines modularen Prüfverfahrens für den Kopfaufprall im Bereich der Windschutzscheibe, bestehend aus einem Versuchs- und einem Simulationsteil, erarbeitet worden. Im Rahmen dieses Projektes wurde ein hybrides Testverfahren bestehend aus Versuch und Simulation ausgearbeitet, das den Bereich der Windschutzscheibe und dabei auch crashaktive Systeme wie Airbags berücksichtigt. Das Testverfahren kombiniert Komponentenversuche mit einem Simulationsteil, in dem Fahrzeug-Fußgänger-Simulationen und lmpaktorsimulationen durchgeführt werden. Zusätzliche Dummyversuche dienten zur Bewertung des Testverfahrens. Alle erarbeiteten virtuellen und realen Testmethoden wurden an einem Referenzfahrzeug (Opel Signum), welches repräsentativ für eine durchschnittliche Mittelklasselimousine steht, durchgeführt. Das Fahrzeug wurde mit einem Airbagsystem ausgerüstet und der Testprozedur mit und ohne diesem System vergleichend unterzogen. Innerhalb dieser Untersuchungen konnte gezeigt werden, dass neue Testmethoden unter Ausnutzung von Simulationen und Komponententests es erlauben, realistischere Versuchsbedingungen unter Berücksichtigung von potenziellen Kopfaufprallpositionen und -zeiten zu definieren. Dabei können sehr gute Übereinstimmungen zwischen Fußgängersimulation und Dummyversuch erreicht werden. Die Randbedingungen für den Kopfaufprall und die Aufprallzeit wurden durch den Einsatz von Fußgängermodellen ermittelt. Weiterhin ermöglichen die Simulationen, zusätzliche Einflussdaten wie Vektoren mit den Kopfaufprallgeschwindigkeiten und -winkeln zu bestimmen.