Abteilung Fahrzeugtechnik
Filtern
Dokumenttyp
Schlagworte
- Braking (7) (entfernen)
Institut
- Abteilung Fahrzeugtechnik (7)
- Sonstige (3)
Motorcycling is a fascinating kind of transportation. While the riders' direct exposure to the environment and the unique driving dynamics are essential to this fascination, they both cause a risk potential which is several times higher than when driving a car. This chapter gives a detailed introduction to the fundamentals of motorcycle dynamics and shows how its peculiarities and limitations place high demands on the layout of dynamics control systems, especially when cornering. The basic principles of dynamic stabilization and directional control are addressed along with four characteristic modes of instability (capsize, wobble, weave, and kickback). Special attention is given to the challenges of braking (brake force distribution, dynamic over-braking, kinematic instability, and brake steer torque induced righting behavior). It is explained how these challenges are addressed by state-of-the-art brake, traction, and suspension control systems in terms of system layout and principles of function. It is illustrated how the integration of additional sensors " essentially roll angle assessment " enhances the cornering performance in all three categories, fostering a trend to higher system integration levels. An outlook on potential future control systems shows exemplarily how the undesired righting behavior when braking in curves can be controlled, e.g., by means of a so-called brake steer torque avoidance mechanism (BSTAM), forming the basis for predictive brake assist (PBA) or even autonomous emergency braking (AEB). Finally, the very limited potential of brake and chassis control to stabilize yaw and roll motion during unbraked cornering accidents is regarded, closing with a promising glance at roll stabilization through a pair of gimbaled gyroscopes.
It is commonly agreed that active safety will have a significant impact on reducing accident figures for pedestrians and probably also bicyclists. However, chances and limitations for active safety systems have only been derived based on accident data and the current state of the art, based on proprietary simulation models. The objective of this article is to investigate these chances and limitations by developing an open simulation model. This article introduces a simulation model, incorporating accident kinematics, driving dynamics, driver reaction times, pedestrian dynamics, performance parameters of different autonomous emergency braking (AEB) generations, as well as legal and logical limitations. The level of detail for available pedestrian accident data is limited. Relevant variables, especially timing of the pedestrian appearance and the pedestrian's moving speed, are estimated using assumptions. The model in this article uses the fact that a pedestrian and a vehicle in an accident must have been in the same spot at the same time and defines the impact position as a relevant accident parameter, which is usually available from accident data. The calculations done within the model identify the possible timing available for braking by an AEB system as well as the possible speed reduction for different accident scenarios as well as for different system configurations. The simulation model identifies the lateral impact position of the pedestrian as a significant parameter for system performance, and the system layout is designed to brake when the accident becomes unavoidable by the vehicle driver. Scenarios with a pedestrian running from behind an obstruction are the most demanding scenarios and will very likely never be avoidable for all vehicle speeds due to physical limits. Scenarios with an unobstructed person walking will very likely be treatable for a wide speed range for next generation AEB systems.
Optimierung des rückwärtigen Signalbildes zur Reduzierung von Auffahrunfällen bei Gefahrenbremsung
(2002)
Das derzeitige Bremssignalbild übermittelt dem nachfolgenden Verkehr nur dass gebremst wird, die Fahrer erhalten jedoch keine Information über die Stärke des Bremsmanövers. Im vorliegenden Bericht wird im Rahmen einer Literaturstudie untersucht, wie das rückwärtige Signalbild optimiert werden könnte, um vor allem Gefahrenbremsungen gesondert darzustellen. Einige praktikable Lösungsvorschläge, die bereits fertig entwickelt sind, werden vorgestellt und analysiert. Es hat sich gezeigt, dass prinzipiell zwei Maßnahmen geeignet sind, die Fahrerreaktionszeit zu verkürzen: - Eine Flächen- und Leuchtdichtevergrößerung der Bremsleuchten wird von den nachfolgenden Fahrern intuitiv als Annäherung an das vorausfahrende Fahrzeug erkannt. - Blinkende Leuchten sind besonders geeignet, die Aufmerksamkeit des nachfolgenden Fahrers auch bei Ablenkung auf das verzögernde Fahrzeug zu lenken. Als mögliche Weiterentwicklung für ein optimiertes rückwärtiges Signalbild wird vorgeschlagen: Bei Ansprechen eines Bremsassistenten oder Antiblockiersystems (ABS) beziehungsweise einer Fahrzeugverzögerung über 7 m/s2 ist die Gefahrenbremsung über ein Blinken der dritten hochgesetzten Bremsleuchte mit 3-5 Hz zu signalisieren. Optional sollten sich zusätzlich die Flächen beziehungsweise Leuchtdichten der beiden unteren Bremsleuchten vergrößern. Diese Maßnahmen erfordern Änderungen in den ECE-Regelungen Nummer 7 und Nummer 48 sowie im Wiener Weltabkommen. Ziel des vorgestellten Lösungsvorschlags ist die Reduzierung der Zahl beziehungsweise Schwere von Auffahrunfällen.
Der Kraftschluss zwischen Reifen und Fahrbahn bestimmt in entscheidender Weise die Fahrsicherheit, insbesondere bei Nässe. Wer sein Fahrzeug mit breiteren Reifen ausrüsten will, hat oftmals keine Möglichkeit, die Eigenschaften der jeweiligen Reifen bei nachlassender Profiltiefe einzuschätzen. Es sollte in dieser Untersuchung geklärt werden, ob die Verwendung von Breitreifen Nachteile für die Fahrsicherheit bei Nässe mit sich bringt, insbesondere unter Berücksichtigung der im Betrieb zwangsläufig nachlassenden Profiltiefe. Im Innentrommelprüfstand der Bundesanstalt für Straßenwesen wurden Kraftschlussuntersuchungen an Pkw-Reifen in drei verschiedenen Breiten durchgeführt. Die Untersuchung beschäftigt sich mit dem Einfluss der Reifenbreite, der Profilgestaltung und der Profilhöhe auf den Kraftschluss bei Nässe. Dabei werden auch die Parameter Fahrgeschwindigkeit, Wasserfilmhöhe, Radlast und Reifeninnendruck berücksichtigt, die den Kraftschluss bei Nässe maßgeblich mitbestimmen. Steigende Fahrgeschwindigkeit, geringere Profiltiefe und höherer Wasserfilm verringern die maximal übertragbaren Bremskräfte. Höhere Radlasten verringern die Tendenz des Reifens, unter dem Druck des sich ausbildenden Wasserkeils aufzuschwimmen und verbessern dadurch das Kraftschlussverhalten bei Nässe. Niedrige Profilhöhen führen wegen der schlechter werdenden Wasserverdrängung zu einem stärkeren Abfall der Kraftschlussmaximalwerte bei steigender Geschwindigkeit oder höherem Wasserfilm. Insgesamt birgt die Kombination von hoher Fahrgeschwindigkeit, niedriger Profiltiefe und hohem Wasserfilm eine extrem hohe Aquaplaninggefahr, die sich noch verstärkt, wenn der korrekte Reifeninnendruck unterschritten wird. Bei niedrigen Fahrgeschwindigkeiten zeigen schmalere Reifen Vorteile, während bei höheren Fahrgeschwindigkeiten und niedrigen Wasserfilmhöhen Breitreifen das Niveau schmaler Reifen sogar übertreffen können. Dieser Effekt ist auf die spezielle laufrichtungsgebundene Profilgestaltung der hier untersuchten Breitreifen zurückzuführen.
New vehicle types are extensively tested to check almost all factors that influence ride and handling. With reference to the Association of German Car Tuners" (VDAT e.V.) valuations, approximately 10% of all cars in Germany are being modified by their owners. 28 % of those modifications" sales are divergent wheel-tire combinations, 13 % are tuning measures on the chassis suspension or wheel spacers. In almost all cases the singular modifications present a general permission for specific vehicles they have been tested in. Combined tuning measures, however, are often checked by just one inspector, following a procedure of mostly subjective assessment criteria. Today, critical attributes are only being observed, in case a vehicle is involved in an accident and the modifications are identified as crash causal factors or as a cofactor on the development of a crash. For the first time, a field study allows a survey of safety affecting chassis modifications. The test layout has to comply with some basic conditions. Different vehicle concepts with a wide margin of modifications are required to get a high transferability of the results. A total amount of more than 150 tested vehicles serves the same purpose. The tests are limited concerning the installation time of measurement techniques and the requirement that no damage, defilement or immoderate wear of the vehicles are accepted by their owners. Due to such factors as well as the driver Ìs acceptance, the vehicles are controlled by its owners instead of robots or test drivers. For keeping down the driver- influence, the lane has narrow boundaries and the driver has to drive in strictly adherence to the given instructions. After gathering all modifications, as well as static and kinematic parameters like the toe and camber angle, dynamic testing of predominantly lateral dynamics is conducted. Besides standardized tests like the ISO 3888-2 (Obstacle Avoidance) or the ISO 14512 (Braking on Surfaces with Split Coefficient of Friction), to test the influence of modified kingpin offsets caused by wheel spacers, some deviant tests are conducted. Those are required due to the demand of objective test results for road tests with vertical induced stimulation of the chassis suspension. Hence, new tests on corner braking with and without vertical stimulation have been developed. The interpretation of data includes thresholds, e.g. the maximum entrance velocity without hitting cones, on the one hand, and the analysis of characteristics of data concerning time and frequency range, "1-second values" and peak response times on the other hand. Besides the thresholds as indicators for the achievable velocities, which are mainly affected by friction coefficients, the vehicle reaction in the course of time characterizes the vehicle reaction in the threshold range and consequently the operational demands on the driver. The field study has started and promises the first long-range analysis of chassis modifications. The results offer a basis for hypothesis and resultant further test layouts for oncoming studies of the identified critical tuning measures.
It is well known that most accidents with pedestrians are caused by the driver not being alert or misinterpreting the situation. For that reason advanced forward looking safety systems have a high potential to improve safety for this group of vulnerable road users. Active pedestrian protection systems combine reduction of impact speed by driver warning and/or autonomous braking with deployment of protective devices shortly before the imminent impact. According to the Euro NCAP roadmap the Autonomous Emergency Braking system tests for Pedestrians Protection will be set in force from 2016 onwards. Various projects and organisations in Europe are developing performance tests and assessment procedures as accompanying measures to the Euro NCAP initiative. To provide synthesised input to Euro NCAP so-called Harmonisation Platforms (HP-) have been established. Their main goal is to foster exchange of information on key subjects, thereby generating a clear overview of similarities and differences on the approaches chosen and, on that basis, recommend on future test procedures. In this paper activities of the Harmonisation Platform 2 on the development of Test Equipment are presented. For the testing targets that mimic humans different sensing technologies are required. A first set of specifications for pedestrian targets and the propulsion systems as collected by Harmonisation Platform 2 are presented together with a first evaluation for a number of available tools.
With the present brake signal pattern the traffic behind only receives the information that the brakes are applied, however, the drivers have no information about the intensity of the braking maneuver. In this report it is examined on the basis of a study of the literature, how the rear signal pattern could be optimized for a special representation of emergency braking maneuvers. In principle there are two suitable possibilities to reduce the driver reaction time: - An increase in the area and luminance of the brake lights intuitively provide the drivers following with an impression of approaching the vehicle in front , - Flashing lights are particularly suited to attract the attention of the driver following to the deceleration of the vehicle ahead , - The following advancement is recommended as an optimization of the rear signal pattern: When the brake assistant or ABS actuates or at a vehicle deceleration rate greater than 7 m/s-², the emergency braking maneuver is signaled by flashing of the third high-mounted brake light at a rate of 3-5 Hz. As an option, the area and luminance of the two lower brake lights could be increased in addition. These measures require changes to ECE Regulations No. 7 and No. 48 as well as to the Vienna Convention. The purpose of the described solution is to reduce the number or severity of rear-end accidents.