Filtern
Dokumenttyp
- Wissenschaftlicher Artikel (10) (entfernen)
Schlagworte
- Mathematical model (10) (entfernen)
Autonomous Emergency Braking (AEB) systems for pedestrians have been predicted to offer substantial benefit. On this basis, consumer rating programmes, e.g. Euro NCAP, are developing rating schemes to encourage fitment of these systems. One of the questions that needs to be answered to do this fully, is to determine how the assessment of the speed reduction offered by the AEB is integrated with the current assessment of the passive safety for mitigation of pedestrian injury. Ideally, this should be done on a benefit related basis. The objective of this research was to develop a benefit based methodology for assessment of integrated pedestrian protection systems with pre-crash braking and passive safety components. A methodology has been developed which calculates the cost of pedestrian injury expected, assuming all pedestrians in the target population (i.e. pedestrians impacted by the front of a passenger car) are impacted by the car being assessed, taking into account the impact speed reduction offered by the car’s AEB (if fitted) and the passive safety protection offered by the car’s frontal structure. For rating purposes, this cost can be normalised by comparing it to the cost calculated for selected cars. The methodology uses the speed reductions measured in AEB tests to determine the speed at which each casualty in the target population will be impacted. The injury to each casualty is then calculated using the results from standard Euro NCAP pedestrian impactor tests and injury risk curves. This injury is converted into cost using ‘Harm’ type costs for the body regions tested. These costs are weighted and summed. Weighting factors were determined using accident data from Germany and GB and the results of a benefit analysis performed by the EU FP7 AsPeCSS project. This resulted in German and GB versions of the methodology. The methodology was used to assess cars with good, average and poor Euro NCAP pedestrian ratings, with and without a current AEB system fitted. It was found that the decrease in casualty injury cost achieved by fitting an AEB system was approximately equivalent to that achieved by increasing the passive safety rating from poor to average. Also, it was found that the assessment was influenced strongly by the level of head protection offered in the scuttle and windscreen area because this is where head impact occurs for a large proportion of casualties. The major limitation within the methodology is the assumption used implicitly during weighting. This is that the cost of casualty injuries to body areas, such as the thorax, not assessed by the headform and legform impactors, and other casualty injuries such as those caused by ground impact, are related linearly to the cost of casualty injuries assessed by the impactors. A methodology for assessment of integrated pedestrian protection systems was developed. This methodology is of interest to consumer rating programmes which wish to include assessment of these systems. It also raises the interesting issue if the head impact test area should be weighted to reflect better real-world benefit.
Die Bundesanstalt für Straßenwesen ermittelt jährlich auf der Grundlage eines Berechnungsmodells die Kosten, die durch Straßenverkehrsunfälle entstehen. Um den Veränderungen der wirtschaftlichen Eingangsparameter und der Entwicklung des Wissensstands zur Bewertung von Unfallschäden gerecht zu werden, wurde dieses Modell im Rahmen eines Forschungsprojektes in Bezug auf das Jahr 2005 überarbeitet und fortgeschrieben (siehe auch ITRD D365799). Demnach ergeben sich für das Jahr 2008 volkswirtschaftliche Kosten in Höhe von 31 Milliarden Euro durch Personen- und Sachschäden infolge von Straßenverkehrsunfällen in Deutschland. Gegenüber dem Vorjahr sind die Unfallkosten damit um circa 3 Prozent (= 970 Millionen Euro) gesunken.
In most of the existing highway capacity manuals, level of service (LOS) of freeway weaving segments and ramp junctions is traditionally defined by the speed, volume or density in critical areas of merge, diverge and weaving manoeuvres. In that traditional concept several capacity values of different critical areas (merge, diverge, weaving) as well as upstream and downstream basic freeway segments within the influence areas are evaluated separately. In this paper, a new model which considers the total segment of freeway merge, diverge, and weaving as an entire object is introduced. A combined volume-to-capacity ratio is used for defining the LOS of the total segment. According to the probability and queuing theory, the volume-to-capacity ratio of the whole segment can be considered as a combination of volume-to-capacity ratios in the different critical areas under consideration. The parameters of the new model can be calibrated with field data. Those parameters are functions of the number of lanes on the freeways, the number of lanes in the on-ramps or off-ramps, the length of the acceleration, deceleration, or weaving sections. Varying the model parameters the function can be fitted to the existing capacity models for different types of weaving segments or ramp junctions. With this model, the traffic quality (LOS) can be obtained directly as a function of the volumes on the freeway and on the on-ramp or off-ramp respectively. The new model has the following advantages: a) a uniform function for all types of freeway weaving segments and ramp junctions, b) traffic quality assessment for all critical areas under investigation in one step, and c) easy calibration. The new model will be incorporated into the new edition of the German Highway Capacity Manual (HBS 201X).
Unfälle zerstören Sachkapital und mindern die der Volkswirtschaft zur Verfügung stehende Arbeitskraft. Zur Entscheidungsunterstützung nutzt die Verkehrssicherheitspolitik in ökonomischen Analysen monetäre Wertansätze, welche sich auf die Folgen der Straßenverkehrsunfälle beziehen und deren Ausmaß quantifizieren. Durch die Bundesanstalt für Straßenwesen (BASt) werden jährlich auf der Grundlage eines Berechnungsmodells die Kosten ermittelt, die durch Straßenverkehrsunfälle entstehen. Um den Veränderungen der wirtschaftlichen Eingangsparameter und der Entwicklung des Wissensstands zur Bewertung von Unfallschäden gerecht zu werden, wurde dieses Modell im Rahmen eines Forschungsprojektes mit Bezug auf das Jahr 2005 überarbeitet und fortgeschrieben. Danach ergeben sich für das Jahr 2009 volkswirtschaftliche Kosten in Höhe von 30,5 Milliarden Euro durch Personen- und Sachschäden infolge von Straßenverkehrsunfällen in Deutschland. Gegenüber dem Basisjahr 2005 sind die Unfallkosten damit um circa 3 Prozent (= 960 Millionen Euro) gesunken.
Estimation of the effects of new emission standards on motorcycle emissions by means of modeling
(2016)
Road traffic is, in addition to the energy sector and the industry, one main source of air pollution and carbon dioxide emissions. Although most countries and manufacturers agreed to environmental regulations to reduce the pollutant emissions, particularly in urban areas with high traffic density, the impact of road traffic emissions on the environment and human health has been growing in importance steadily. Due to stricter emission standards and the binding use of emission-reducing systems (e.g. three-way catalyst) hydrocarbon emissions from passenger cars have been reduced significantly since the last two decades. Unlike to passenger cars the emissions standards of powered two-wheelers have not been adjusted since 2006 although their share of hydrocarbon emissions to the total amount of hydrocarbon emissions of road traffic is estimated to be disproportionately high. Due to the new regulation (EU) No. 168/2013 powered two-wheelers have to fulfill new emission standards from 2016 (Euro 4) and 2020 (Euro 5) onwards. Besides new limits for the tailpipe emissions the evaporative emissions are regulated separately for the first time, as they make up a high proportion to the total hydrocarbon emissions in this vehicle class. In this context, the calculation and forecast of road traffic emissions is an important tool to verify compliance of climate targets and to assess the reduction potential of emission-reducing systems. For that purpose the Federal Highway Research Institute (BASt) uses the emission- and calculation tool TREMOD (Transport Emission Model) which provides baseline data and calculated results for pollutants in almost every differentiation e.g. vehicle category, traffic situation and road type. Moreover, estimations of future emission trends, stock information and mileage distribution can be made. The main objective is to illustrate the impact of the upcoming emission standards Euro 4 and Euro 5 on the operational hydrocarbon emissions of powered two-wheelers based on statistical estimations. The significant aspect is to generate scenarios to show the reduction potential of hydrocarbon emissions of powered two-wheelers, differentiated into motorcycles and small motorcycles, in relation to the total share of hydrocarbon emissions in this vehicle class and to the total hydrocarbon emissions from road traffic. As a part of their research, the authors can make initial statements about the possible effect of the new emission standards of regulation (EU) No. 168/2013 by means of modeling with TREMOD.
Die Polierresistenz der Gesteine beeinflusst nach dem Stand der Forschung maßgeblich die Griffigkeit einer Fahrbahnoberfläche. Diese Gesteinseigenschaft wird in Europa seit langem und im weit überwiegenden Teil der Fälle mit dem so genannten Polished Stone Value (PSV) beschrieben und in Deutschland nach den DIN EN 1097-8 ermittelt. Als Prüfmittel sind für das Verfahren ein Kontrollgestein und Poliermittel aus Naturkorund vorgeschrieben, die genau spezifiziert und aus England zu beziehen sind. Nachteilig ist bei dem Prüfverfahren die unregelmäßige Verfügbarkeit und die Inhomogenität der Prüfmittel, die im Wesentlichen aus der europaweiten Anwendung des Verfahrens resultieren. Als Alternative zu dem englischen Kontrollgestein wurde bereits 2007 ein nationales Kontrollgestein ergänzend in die Technischen Prüfvorschriften für Gesteinskörnungen (TP Gestein-StB) Teil 5.4.1 aufgenommen. Die Frage nach der Möglichkeit des Ersatzes des Poliermittels und auch der Auswirkung seines Einsatzes auf die Präzision bei der Ermittlung des PSV wurde im Rahmen eines Forschungsprojekts untersucht. Zusammengefasstes Ergebnis ist, dass das alternativ eingesetzte Poliermittel aus Quarz für das Prüfverfahren geeignet ist und eine mindestens vergleichbare Präzision der Prüfergebnisse erwartet werden kann. Aufgrund der abweichenden Polierwirkung des Poliermittels und der abweichenden Polierresistenz des nationalen Kontrollgesteins ist jedoch die Berechnungsformel anzupassen, um den langjährigen Bewertungshintergrund und die daraus resultierenden Anforderungen in den Regelwerken beibehalten zu können. Die Vorgehensweise, die Überlegungen und das Ergebnis des Forschungsprojekts sind in dem Artikel dargestellt.
Mit einem Simulationsmodell wurden die Auswirkungen des Lkw-Überholverbots auf zweistreifigen Richtungsfahrbahnen in der Ebene und an Steigungsstrecken untersucht. Dabei wurde ein Einfluss von Anschlussstellen und von vorausliegenden Abschnitten (zum Beispiel Baustellen, Rückstau) ausgeschlossen. In Abhängigkeit vom Lkw-Anteil und von der Verkehrsstärke wurden Bereiche aufgezeigt, in denen sich die Geschwindigkeit des Verkehrsflusses steigert und in denen sich die Anzahl der Konfliktsituationen beim Fahrstreifenwechsel reduziert. Eine Umsetzung der Ergebnisse in ein Steuerungverfahren von Wechselverkehrszeichenanlagen ist damit möglich. Vor einer Anordnung des Lkw-Überholverbots mit statischer Beschilderung kann mit dem entwickelten Modell berechnet werden, zu welchen Tageszeiten und ab wieviel Tonnen (zum Beispiel größer 4 t) eine solche Anordnung sinnvoll ist.
Im Rahmen des Verkehrsforschungsprogramms "Mobilität und Verkehr" wurde von 2001 bis 2003 das Verbundprojekt "Leiser Straßenverkehr - Reduzierte Reifen-Fahrbahn-Geräusche" bearbeitet. Das Augenmerk der Bearbeitung lag auf der Optimierung der Komponenten des geräuscherzeugenden Gesamtsystems Fahrzeug-Reifen-Fahrbahn-Fahrbahnübergang, insbesondere für Pkw-Reifen. Die Ergebnisse dieses Projekts, wie auch weitere europäische Erkenntnisse, waren eine Basis für die Konzeption des Nachfolgeprojekts "Leiser Straßenverkehr 2". Die im Jahr 2005 mit 10 Partnern begonnenen Arbeiten lassen sich den Teilverbünden Leise Reifen, Leise Straßen und Erfolgskontrolle zuordnen. Die Schwerpunkte der Arbeiten liegen auf der Entwicklung leiser Lkw-Reifen und der integralen Verbesserung offenporiger Deckschichten. Die Entwicklung eines numerischen Reifenmodells mit Fahrbahnkontakt, mit dem Ziel der rechnergestützten Entwicklung auch akustisch optimierter Reifen, wird fortgesetzt. Hinzu kommt die akustische Optimierung der Fahrbahnübergänge. Die Umsetzung der Ergebnisse in die Praxis in Form von Erprobungsstrecken und der Herstellung akustisch optimierter Reifen stellt einen wichtigen Teil des Konzepts dar. Hier sind insbesondere drei Bundesländer und Industrieunternehmen eingebunden. Die Gesamtarbeiten sollen 2008 abgeschlossen sein. In diesem Beitrag werden Zwischenergebnisse aus den einzelnen Teilverbünden vorgestellt.
In diesem Beitrag werden die Emissionsmodelle der RLS-90 und der RVS (rein A-bewertete Verfahren), von NMPB 2008, SonRoad (mit Normspektrum) und CNOSSOS (differenzierte spektrale Angaben der Schallemission) beschrieben und verglichen. Die Ansätze für Roll- und Motorgeräusch sind zum Teil sehr ähnlich, weisen aber auch signifikante Unterschiede auf, die sich auch im Gesamtgeräuschpegel bemerkbar machen. Eine Abschätzung der Unsicherheiten ergibt insgesamt circa 3 dB(A). Für den Einfluss der Gradiente (Steigung/Gefälle) kann (noch) keine abschließende Beurteilung der Unsicherheit gemacht werden, da sie in den einzelnen Emissionsmodellen höchst unterschiedlich behandelt wird. Für unterschiedliche Straßenbeläge kann die Unsicherheit mit 1 bis 2 dB(A) abgeschätzt werden. Die Unsicherheit aufgrund unsicherer Angaben bei Verkehrsmengen und Geschwindigkeiten liegen in einem ähnlichen Bereich.
Although many German monitoring sites report declines of NOx concentrations, NO2-concentrations actually stagnate or even increase quite often. Various analyses have identified the altered compositions of nitrogen oxides (NO2/NOx-ratio) emitted by motor vehicles (resulting in an increase of primary NO2-emissions) as well as the chemical environmental conditions (mainly ground level ozone) as the main causes. The chemical conversion of NO to NO2 is often parameterized in dispersion calculations of exhaust emissions. A widely applied conversion model is the so-called Romberg approach from 1996. However, the Romberg approach has to be re-evaluated to accommodate the above-mentioned conditions. This article presents an adjustment to the Romberg approach in accordance with the measured data from 2000 to 2006, taking into consideration substantially higher NO2/NOx-ratios especially for higher NOx-concentrations. Model calculations with OSPM (Operational Street Pollution Model) including its internal chemistry module are able to reproduce very well the trends in the measured annual NO2-concentrations over a 10 year period. The relevant parameters for variations between the years are the NOx-emissions, primary NO2-emissions, ozone concentrations, wind conditions, and background concentrations. A simplified chemistry model based on annual mean NOx- and NO2-concentrations, and background ozone concentrations, as well as primary NO2-emissions is presented as a better method than the updated Romberg approach. This model simulates the annual mean NO2-concentrations much more accurately than the conventional and the updated Romberg approaches.