Filtern
Erscheinungsjahr
- 2014 (25) (entfernen)
Dokumenttyp
Sprache
- Englisch (25) (entfernen)
Schlagworte
- Safety (13)
- Sicherheit (13)
- Anfahrversuch (9)
- Deutschland (9)
- Germany (9)
- Bewertung (8)
- Evaluation (assessment) (8)
- Method (8)
- Compatibility (7)
- Fahrzeug (7)
Structured road markings are becoming popular as edge line on high speed roads, ensuring night time visibility (retroreflection) during rain. These markings are often also "audio-tactile": vehicles (un)intentionally driving over it may produce much more tyre/road sound, which may be observed in the vehicle but also in the vicinity. The sound increase inside the car can be considered as a positive side effect, as it alarms the driver and may be very helpful for the prevention of "doze off" traffic accidents. The sound increase perceived outside the car however, may have a positive aspect as it can warn people on the emergency lane about the approaching vehicle, but it may as well annoy people living around. A method for the assessment of the acoustic properties of audio-tactile markings has been developed. It is mainly based on the "Close Proximity" (CPX) method, an ISO method intended for the acoustic assessment of pavements. The results of measurement campaigns with CPX trailers in Belgium and Germany according to a specially designed procedure are presented. The feasibility of the method is discussed. The research has been carried out in the frame of the standardization activities of the CEN working group CEN/TC226/WG2 "Horizontal signalization".
In Europe, in situ measurements of sound reflection and airborne sound insulation of noise barriers are usually done according to CEN/TS 1793-5. This method has been improved substantially during the EU funded QUIESST collaborative project. Within the same framework, an inter-laboratory test has been carried out to assess the repeatability and reproducibility of the newly developed method when applied to real-life samples, including the effect of outdoor weather variability and sample ageing. This article presents the statistical analysis of the inter-laboratory test results, and the values of the repeatability and the reproducibility, both in one-third octave bands and for the single-number ratings. The estimated reproducibility values can be used as the extended measure of uncertainty at the 95% credibility level in compliance with the ISO GUM. The repeatability and reproducibility values associated with airborne sound insulation are also compared with the corresponding values for laboratory measurements in building acoustics and an acceptable agreement is found.
The goal of the project FIMCAR (Frontal Impact and Compatibility Assessment Research) was to define an integrated set of test procedures and associated metrics to assess a vehicle's frontal impact protection, which includes self- and partner-protection. For the development of the set, two different full-width tests (full-width deformable barrier [FWDB] test, full-width rigid barrier test) and three different offset tests (offset deformable barrier [ODB] test, progressive deformable barrier [PDB] test, moveable deformable barrier with the PDB barrier face [MPDB] test) have been investigated. Different compatibility assessment procedures were analysed and metrics for assessing structural interaction (structural alignment, vertical and horizontal load spreading) as well as several promising metrics for the PDB/MPDB barrier were developed. The final assessment approach consists of a combination of the most suitable full-width and offset tests. For the full-width test (FWDB), a metric was developed to address structural alignment based on load cell wall information in the first 40 ms of the test. For the offset test (ODB), the existing ECE R94 was chosen. Within the paper, an overview of the final assessment approach for the frontal impact test procedures and their development is given.
Road markings are an essential component of a safe road. In particular, the optical guidance at night and under wet conditions rates high. Special surface textures of road markings can enhance the nighttime visibility during wetness, but they can lead on the other hand to noise emission during passages of vehicles and thus annoy residents. In the present study the tyre/road marking noise is analysed based on two different measurement methods for traffic noise: Several different road markings with increased nighttime visibility during wetness were overrun and the noise was determined by controlled coast-by measurements as well as close-proximity measurements. For both measuring methods the averaged A-weighted sound pressure levels were determined and an analysis of the third octave spectra was performed in order to identify annoying tonal components. The results of both measurement methods were compared with each other. Limitations of the individual measurement methods were overcome by combining the data. Properties of road marking noise depending on the texture of the marking are discussed in relation to those of road surface noise. The results will help specifying road marking texture types that ensure less annoyance and at the same time good visibility at wetness and night-time.
The use of alcohol interlocks for DUI offenders is widespread around the world. in North America and Australia alcohol interlocks are core elements in the countermeasure system against DUI recidivism. Based on a European experience exchange hosted by the Federal Highway Research Institute (BASt) in October 2013, key features of European alcohol interlock programmes are illustrated. In addition, key findings from international alcohol interlock research are presented. They point towards a need for an accompanying rehabilitative measure in order to achieve long-lasting behavioural changes in the offender. Data from the interlock recorder can be used as predictor for recidivism risk, but also as objective data to aid counselling. Finally, an example of an accompanying rehabilitative measure, which was specifically developed for interlock programmes within a BASt project, is given.
In Germany road tunnels on major roads which are longer than 400 m have to be monitored permanently. For that purpose the tunnels are equipped with a multitude of monitoring and detection systems whose data and messages are transmitted to tunnel control centres. Due to the higher traffic density, the increasing number of tunnels to be monitored and road users" demand of higher safety and security levels, the strains on operating staff of tunnel control centres have continuously been growing. Therefore, innovative approaches have been developed in two recent German research projects: RETISS " Real Time Security Management System, and ESIMAS " Real-time Safety Management System for road Tunnels. Both systems are designed to allow faster and more efficient reaction of tunnel operators in order to maintain the capacity and availability of transport infrastructures but also to improve the safety and security of road users.
The market introduction and penetration of electric vehicles can be seen as a milestone in order to reduce the environmental burden imposed by the transport sector. The wide-spread use of electric vehicles powered by electricity from renewable sources promises a substantial reduction of local emissions in urban areas as well as greenhouse gas emissions. To be a successful mobility alternative several obstacles and challenges have to be overcome first. Especially the customers' purchase decision determines finally whether an innovation like electromobility will be successful. Therefore, this paper concentrates on demand-related obstacles and barriers for a broad market deployment of electric cars. Within the Electromobility+ project eMAP these issues are investigated via a consumer survey. It was designed to identify the awareness of potential consumers of electric cars as well as give an estimate of the attitude towards this new technology. In addition to the picture of potential demand-related obstacles the consumers were asked to evaluate the suitability of various promotion measures.
In 2011 399 cyclists died in road accidents in Germany and another 76.351 cyclists have been injured. Since 2000 the number of injured or fatally injured cyclists remained on the same high level. Cyclists form 19% of all casualties in German road traffic, although the modal split rate of this transport mode in 2008 was only 10% of trips and resp. 3% of kilometres per day. The high proportion of fatally and seriously injured shows the high vulnerability of cyclists. The demographic shift towards an older population in Germany and the governmental recommendation of increased bicycle use as an ecological, economical and healthy alternative to other modes of transport lead to the assumption that bicycle use especially of elderly people will increase. Based on these facts about the German cyclists' situation a representative survey of 2.000 cyclists was conducted. Results display use patterns and accident involvement on a descriptive level. Overall 7.7% of cyclists report to have been involved in at least one road traffic accident within the last three years. The performed path model analysis reveals an acceptable model fit. Though the explained variance of accident involvement of the applied psychological factors was low, significant relations between several of these factors and especially risky behaviour could be found.
In the European Project FIMCAR, a proposal for a frontal impact test configuration was developed which included an additional full width deformable barrier (FWDB) test. Motivation for the deformable element was partly to measure structural forces as well as to produce a severe crash pulse different from that in the offset test. The objective of this study was to analyze the safety performance of vehicles in the full width rigid barrier test (FWRB) and in the full width deformable barrier test (FWDB). In total, 12 vehicles were crashed in both configurations. Comparison of these tests to real world accident data was used to identify the crash barrier most representative of real world crashes. For all vehicles, the airbag visible times were later in the FWDB configuration. This was attributed to the attenuation of the initial acceleration peak, observed in FWRB tests, by the addition of the deformable element. These findings were in alignment with airbag triggering times seen in real world crash data. Also, the dummy loadings were slightly worse in FWDB compared to FWRB tests, which is possibly linked to the airbag firing and a more realistic loading of the vehicle crash structures in the FWDB configuration. Evaluations of the lower extremities have shown a general increasing of the tibia index with the crash pulse severity.
Rural roads (highways) in Germany have to provide both high road safety and an appropriate level of service in accordance with their function in the road network. Single carriageway rural roads often underperform these expectations. An analysis of severe accidents on rural roads found two main contributing factors. First, high or inappropriate speed leads to accidents caused by the loss of control of the vehicle. Second, unsafe passing manoeuvres related to a misjudgement of sight distance, speed of oncoming vehicles or a misjudgement of the driver vehicle's acceleration capability. On the five roads where unsafe passing manoeuvres were a main contributing factor to accident occurrence, single short passing lanes (600 m to 1.2 km) were built to provide safe passing. On the remaining two-lane sections passing was prohibited by road signs and road marking. This paper investigates the effect of this design change on the accident situation and on traffic flow. The research project is based on a before/after comparison of traffic and accident data. Traffic volume, vehicle types and their velocities as well as the time gaps between the vehicles were recorded at different cross-sections. The result shows a significant improvement in road safety. This improvement was especially noted for severe head-on crashes, which were reduced to almost zero. The analysis of traffic flow on these roads pointed out that the chosen lengths of passing lanes were sufficient for safe passing and thereby reduced the need for dangerous driving behaviour. The recommendations of this research were fundamental for the determination of the design parameters of the second highest design class (EKL 2) in the new German Rural Road Design Guideline (RAL) published in spring 2013.