Sonstige
Filtern
Dokumenttyp
- Konferenzveröffentlichung (14) (entfernen)
Schlagworte
- Measurement (14) (entfernen)
Institut
- Sonstige (14) (entfernen)
Um ein Bild von der aktuellen Messunsicherheit bei der Bestimmung von Tetrahydrocannabinol (THC) in Serum zu erhalten, wurden von sieben forensisch-toxikologischen Laboren rechtsmedizinischer Institute Daten der letzten Jahre erhoben. Zur Abschätzung der Messunsicherheit wurde eine Einteilung in zufällige Fehler (Präzision) und systematische Fehler (Richtigkeit) vorgenommen. Ergebnisse zur Richtigkeit wurden aus Daten von Ringversuchen ermittelt. Es ergab sich eine mittlere erweiterte Messunsicherheit für die THC-Bestimmung von ca. 33 %, das heisst, bei einem Messwert von 1 ng/ml liegt der "wahre Wert" mit circa 95 prozentiger Wahrscheinlichkeit im Intervall zwischen 0,67 und 1,33 ng/ml. Dieses Ergebnis bestätigt, dass die verwendete Analytik geeignet ist, bei Konzentrationen um 1 ng/ml einen sicheren Substanznachweis zu führen. Es ist erkennbar, dass bei der THC-Bestimmung im Serum in der Regel der Richtigkeitsanteil an der Messunsicherheit größer ist als der Präzionsanteil.
Federal highway A 26 in Germany : reinforced dams in soft soils - control method according DIN 1054
(2004)
In 2001 the construction of the Federal Highway A 26 in Lower Saxony (north of Germany) was started. In this area the underground is without any substantial bearing capacity as it consists of soft layers ( clay, peat) with a thickness of up to 12 m. Because it was not possible to exchange the soil neither completely nor partially pre-loading procedure (consolidation method) was chosen for this construction. Short- and long-term stability are ensured by the use of high-tensile fabrics for reinforcement at the dam basis. The vertical and horizontal deformations and the stress changes in the soil, caused by the pre-load procedure, has to be controlled by special geotechnical measurements. Additionally, in the higher parts of the dam the strain behaviour of the high-tensile fabrics is measured. These measurements form the basis for the application of the control method according DIN 1054. In this article, the special circumstances of this project are described. Further on the geotechnical measurements, the winning and evaluation of the necessary parameters of the subsoil, and the consequences of these data for the ongoing of the project are laid down. Intermediate results of the geotechnical measurements are described.
Zur Ergänzung der bestehenden Routineverfahren in der forensischen Blutalkoholanalytik wurde ein massenspektrometrisches Verfahren mit d6-Ethanol als internem Standard entwickelt. Ziel war die Anwendung eines beweissicheren Bestimmungsverfahrens, bei dem Ethanol über die Retentionszeit und Substanzeigenschaften identifiziert wird. Die Pilotstudie belegt, dass die forensische Blutalkoholbestimmung durch Anwendung eines gaschromatographischen und massenspektrometrischen Verfahrens mit Dampfraumanalyse routinemäßig möglich ist. Im Gegensatz zum GC- und ADH-Verfahren ist die massenspektrometrische Blutalkoholbestimmung beweissicher. Die Autoren empfehlen die Aufnahme in die Richtlinien zur Bestimmung der Blutalkoholkonzentration für forensische Zwecke. Die Arbeit wurde vom Bund gegen Alkohol und Drogen im Straßenverkehr e.V. (B.A.D.S.) unterstützt.
Diese Studie erfolgte als eine erste Prüfung der Frage, ob 0,1 Promille als Sicherheitszuschlag für eine Bestimmung eines Blutalkoholwertes von 0,1 Promille aus Gründen der Messunsicherheit angebracht und ausreichend ist. Beides trifft zu. Obwohl zur Zeit der Studie noch nicht bei oder unter 0,2 Promille kalibriert wurde, bestimmten alle Labors eine Blutalkoholkonzentration von 0,08 Promille mit einem Wert unter 0,18 g/L (Cmax ADH: 0,15 g/L = CmaxGC: 0,15 g/L = Blutalkoholkonzentration (BAK) von 0,12 Promille). Es bestand kein Bias zwischen beiden Verfahren. Festgestellte Standabweichungen: ADH: 0,021 g/L, GC: 0,025 g/L. Ein Sicherheitszuschlag von 0,1 Promille auf 0,1 Promille umfasst demnach vier Standardabweichungen und bietet für die neue Regelung im Paragrafen 24 Straßenverkehrsgesetz (StVG) bei der richtliniengemäß ausgeführten forensischen Blutalkoholbestimmung genügend Analysensicherheit.
Die aktuellen Richtlinien zur Bestimmung der Blutalkoholkonzentration (BAK) für forensische Zwecke (BAK-Richtlinie, 2007) lassen unter bestimmten Bedingungen auch zwei verschiedene gaschromatographische Analysen anstatt der häufig angewandten Kombination Gaschromatographie und enzymatische Methode ADH zur Bestimmung des Blutalkoholgehaltes zu. Untersucht wurde die Messpräzision zweier gaschromatographischer Verfahren bei der Alkoholanalytik im Vergleich zur häufiger angewandten Methodenkombination. In mehr als 50 Prozent der Fälle hat sich bei den verglichenen Methodenkombinationen ein identischer Mittelwert ergeben. Ansonsten waren die Abweichungen gering. Damit werden die hohen Anforderungen, die an die forensische Blutalkoholbestimmung gestellt werden, durch die modernen Laborautomaten erfüllt.
Der Beitrag berichtet in einem ersten Teil über die in den Niederlanden angewendeten Inspektionstechniken zur Feststellung von Schäden (Rissen) bei orthotropen Stahlfahrbahnplatten und in einem zweiten Teil über die Instandsetzung der Moerdijkbruecke mit einer zusätzlichen Deckschicht aus bewehrtem hochfesten Stahlfaserbeton. Die Ausführungen zu den Inspektionstechniken umfassen die visuelle Inspektion, magnetische Inspektion, Farbeindringprüfung, Ultraschallprüfung und Diffraktionseffekt bei Anstrahlen von Fehlern (Time of Flight Diffraction (TOFD)) sowie radiographische Untersuchungen und das Wirbelstromverfahren. Für jede dieser Methoden wird ihre Wirkungsweise, Handhabung und der Anwendungsbereich angegeben. Die Moerdijkbrücke ist eine der meistbefahrenen Brücken in den Niederlanden mit einem erheblichen Schwerverkehrsaufkommen und weist etliche Schäden am Deckblech auf. Die bisher durchgeführte Instandsetzung durch Ausbessern der Längsschweissnähte führte nicht zum erhofften Erfolg. Der Bauherr entschloss sich daher, die Gussasphaltschicht durch einen bewehrten hochfesten Stahlfaserbeton mit einer Dicke von 5 cm mit Verbund zum Stahldeckblech zu ersetzen. Die Spannungen im Deckblech konnten auf diese Weise um einen Faktor 4 bis 5 reduziert werden. Die Methode reagiert jedoch empfindlich auf Abweichungen der Mischungsverhältnisse des Betons und der Viskosität.
The grip between the road surface and vehicle tires is the physical basis for the moving of all vehicles in road traffic. In case of an accident the available grip level is one of the most relevant influence factors, influencing the causation and the procedure of the accident. However, the estimation of the grip level is not easy and therefore, is commonly not done on the accident scene. This is especially true for the measurement of the water depth. Until now, real accident databases provide no measurement data about the grip level and the water film depth and thus, the estimation of its influence is not possible yet. From the tyre manufacturers point of view, it is important to know about the road conditions (namely grip level, macro-texture, water depth, temperature) at the accident scene, as well as the operating conditions of the vehicles (braking, loss of control, speed, etc). These data is necessary to define relevant tyre traction tests for the end-user and for regulations. For this reason VUFO and Michelin developed a consistent method for the measurements of grip level and water depth for the accidents of the GIDAS database. The accident research team of Dresden, which documents about 1000 accidents with at least one injured person every year, is measuring the micro-roughness and the macro-roughness directly on the spot. For the measurement of the micro-roughness a Skid Resistance Tester (British Pendulum) is used. The Mean Texture Depth (describing the macro-roughness) is measured by the Sand Depth Method. Since June 2009, measurements for more than 700 accidents including 1200 participants have been carried out. In case of wet or damp road conditions during the accident, the water depth is measured additionally. Therefore VUFO and Michelin developed a special measurement device, which allows measurements with an accuracy of 1/10 millimetre. The measurement point at the accident scene is clearly defined and thus, the results are comparable for all different accidents and participants. The use of the GIDAS database and the accident sampling plan allows representative statements for the German accident scenario. With this data it is possible for the first time to have an accurate view of the road conditions at the accident scene. One possibility is a more detailed estimation of hydroplaning accidents using the actually measured water depths. The development of new testing methods and new tires can be based on the real situation of the road infrastructure. Furthermore, the combination of the technical GIDAS data and the measured road surface properties can also be used for the estimation of effectiveness of several safety systems like the brake assist and/or emergency braking systems. The calculation of a reduced collision speed due to the use of a brake assist is only one example for the application of real measured grip level data.
Having a look at safety to traffic and the prevention of accidents it can be observed that technical improvements in active safety of vehicles have let to various positive effects in this area. Among other components the tyre-road-contact takes a key role in the development of active safety technologies. All forces in accelerating, breaking and vehicle guidance have to be transmitted through the tyre-road contact area by friction forces. A common way to characterize a friction process is to identify the coefficient of friction μ between two touching materials. Even though there are several approaches to experimentially characterise road surfaces, no standard method exists. In this paper an overview of existing test methods is given. Furthermore the preliminary design of a newly developed portable test device with its possibility to investigate the tyre-road-friction of arbitrary roads or even places of accidents is shown.
For the determination of the road surface roughness common methods have been established, like Skid Resistance Tester (SRT) or the Sideway-force Coefficient Routine Investigation Machine (SCRIM). Both methods are used to measure a comparable and reliable maximum friction potential value and to assess the quality of the road surface. However, the comparison of the measurements under real conditions and the results of measurements with SRT and SCRIM showed only minor correlations. The paper shows the comparison between these standardised methods and real vehicle braking tests and discusses the results.
New vehicle types are extensively tested to check almost all factors that influence ride and handling. With reference to the Association of German Car Tuners" (VDAT e.V.) valuations, approximately 10% of all cars in Germany are being modified by their owners. 28 % of those modifications" sales are divergent wheel-tire combinations, 13 % are tuning measures on the chassis suspension or wheel spacers. In almost all cases the singular modifications present a general permission for specific vehicles they have been tested in. Combined tuning measures, however, are often checked by just one inspector, following a procedure of mostly subjective assessment criteria. Today, critical attributes are only being observed, in case a vehicle is involved in an accident and the modifications are identified as crash causal factors or as a cofactor on the development of a crash. For the first time, a field study allows a survey of safety affecting chassis modifications. The test layout has to comply with some basic conditions. Different vehicle concepts with a wide margin of modifications are required to get a high transferability of the results. A total amount of more than 150 tested vehicles serves the same purpose. The tests are limited concerning the installation time of measurement techniques and the requirement that no damage, defilement or immoderate wear of the vehicles are accepted by their owners. Due to such factors as well as the driver Ìs acceptance, the vehicles are controlled by its owners instead of robots or test drivers. For keeping down the driver- influence, the lane has narrow boundaries and the driver has to drive in strictly adherence to the given instructions. After gathering all modifications, as well as static and kinematic parameters like the toe and camber angle, dynamic testing of predominantly lateral dynamics is conducted. Besides standardized tests like the ISO 3888-2 (Obstacle Avoidance) or the ISO 14512 (Braking on Surfaces with Split Coefficient of Friction), to test the influence of modified kingpin offsets caused by wheel spacers, some deviant tests are conducted. Those are required due to the demand of objective test results for road tests with vertical induced stimulation of the chassis suspension. Hence, new tests on corner braking with and without vertical stimulation have been developed. The interpretation of data includes thresholds, e.g. the maximum entrance velocity without hitting cones, on the one hand, and the analysis of characteristics of data concerning time and frequency range, "1-second values" and peak response times on the other hand. Besides the thresholds as indicators for the achievable velocities, which are mainly affected by friction coefficients, the vehicle reaction in the course of time characterizes the vehicle reaction in the threshold range and consequently the operational demands on the driver. The field study has started and promises the first long-range analysis of chassis modifications. The results offer a basis for hypothesis and resultant further test layouts for oncoming studies of the identified critical tuning measures.